A 36-lb triangular plate is supported by three wires as shown. Determine the tension in each wire, knowing that a= 6 in. ce Syststructure.comA 36-lb triangular plate is supported by three wires as shown. Determine the tension in eachwire, knowing that a = 6in.47D24 in.aA16 in.-8 in.

Consider the free body diagram of the triangular plate:

Answered: A 36-lb triangular plate is supported…

A 36-lb triangular plate is supported by three wires as shown. Determine the tension in each wire, knowing that a 6in. 19 D 24 in. C a B. 16 in.- 8 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. A 30 m steel tape weighs 1.5 kg and is supported at its end points and at the 5 and 15 m marks.…

Q: Determine the magnitude of the pin force a Assume W = 895 lb, a = 4.8 ft, b = 3.3 ft, r = r W C…

Q: Find the moment about the front wheels (point B) due to the cart's 320¹b weight, the 120 crate, and…

A: Given data Carts weight = 320 lb Weight of crate = 120 lb Tension in rop = 75 lb

Q: Three cables having an area of 0.05 in? each is carrying the load W as shown. With no stress, the…

A: Given, A = 0.05 in2 E = 29000 ksi

Q: Determine the time needed to pull the cord at B down 4 ft starting from rest when a force of O lb is…

Q: A 4.8-ft-long steel wire of 1/4 -in.-diameter is subjected to a 750-lb tensile load. Knowing that E…

A: This question is related to Strength of Material. In this question we calculate Elongated value of…

Q: The top of the folding workbench has a mass of 55 kg with mass center at G. Calculate the magnitude…

Q: 2.5 KN 7 ΚΝ 15 KN/m 30° A B 2m 4m Im Figure A1/ Rajah A1

Q: 2 k 2 k 2 k - 5 ft- 5 f 5 ft 5 ft H F 5 ft as D 03. FUND-PROS 037 Pearen Calculate forces in memhers…

A: To find the force in member GF ,DG and CD-

Q: If each cord can sustain a maximum tension of 50 N before it fails, determine the greatest weight of…

A: Draw the free body diagram. From the figure,

Q: 1) Define if the section is ductile or brittle, then calculate the nominal moment of the section…

A: Given Data:fc=280kg/cm2=27.5N/mm2Fy=4200kg/cm2=412N/mm2b=30cm=300mmd=50cm=500mm

Q: A 30 m steel tape was standardized at a temperature of 20°C and under a pull 5 kg. The tape was used…

Q: A 5 cmx12 cmx6 m wooden plank (S.G.wood = 0.70) is required to stand vertically in water. To reduce…

A: We have to determine the value of draft of the wooden plank and metacentric height of the whole…

Q: Situation 9. To support the tent, the tension in the rope AB must be 35 lb. What are the tensions in…

A: The given diagram is shown below,

Q: The device shown is used to straighten bowed decking boards just prior to final nailing to the…

A: Given, r=507 mm s=175 mm α=2.1°β=15° Force=P

Q: If coefficient of friction is 0.27, determine the maximum weight of the rectangular block before it…

Q: Examine the diagram to the right. Calculate the tension in the rope. a) 5N b) ON ) 49.05 N c) 9.81 N…

A: Given data : The value of mass of block m=5 kg The value of acceleration due to gravity g=9.81 m/s2…

Q: A steel post (E = 30x10° psi) having thickness h = in. and height l = 71 in. supports a stop sign…

A: Stress is defined as the force of resistance per unit area given by a body against deformation. The…

Q: M. A B E Hinge /C D L2 4 m 6 m

Q: The homogeneous bar AB weighing 1800 lb is supported at either end by a steel cable. Calculate the…

A: (d) is the right option

Q: The man attempts to support the load of boards having a weight W and a center of gravity at G. If he…

A: The free body diagram of figure is given below.

Q: Determine the maximum weight of the bucket that the wire can support so that no single wire develops…

A: Equating the forces in the horizontal direction. ∑Fx = 0…

Q: 2-9. If a horizontal load applied to the bar AC causes point A to be dis to the right by an amount…

Q: supporting each block. WA= 200 N, WB= 300 N. Coeff friction is 0.2. B 4 A 3.

Q: The magnitude of the resultant force acting on the bracket is to be 400 N. Determine the magnitude…

A: Resultant force = 400 N To find magnitude of F1 force

Q: * .Q1: determine the moment at point A 10 3 12 130 lb

Q: ad moments, and bend ad. K=K,= 1.0. Use LRF

A: (a) Calculate the factored axial compressive load. Here, is the dead load, is the live load.…

Q: Calculate the magnitude of the tension T and the angle O for which the eye bolt will * ?be under a…

A: Given data, Resultant downward forces = 15 kN To find out the magnitude of T and angle.

Q: Find the moment about the front wheels (point B) due to the cart's 320¹b weight, the 120 crate, and…

A: Given:- Three force are Cart's weight=320 lbWeight of crate=120 lbTension in rope=75 lb To find:-…

Q: e and what portion of the lighter sphere protrudes from the water? They are connected with a short…

Q: A rope ABCD is looped over two pipes as shown. Knowing that the coefficient of static friction is…

Q: Determine the distance y̅ to the center of gravity of the homogeneous rod.

A: Given: Height of the cable = 2 m Width = 1 m.

Q: 5. Find the maximum weight of the bucket that the wire system can support so that no single wire…

Q: alculate the force at each point of the structure due to the applied and rrounding forces, indicate…

Q: LA B- 50 40 0 350 N

Q: Note: 1 box is 1ft x 1 ft Given the system of forces shown below, Determine the following: (a)…

A: According to guidelines we are supposed to solve only first 3 sub-parts AMoment of 224 lb force…

Q: Two cables are tied together at C and are loaded as shown. Knowing that P = 385 N and R = 238 N,…

Q: If the bucket weighs 60 lb, determine the tension developed in each of the wires. B 135° A 5 35°

A: Finding out tension in wires.

Q: 13. A lintel in a brick wall spans 8 feet between supports. The load is considered to be triangular,…

A: Span of beam (l) = 8 ft. The load is triangular in shape increasing from zero at the left end to 600…

Q: 2. (a) Replace the force system acting on the post by a resultant force and (b) couple moment at…

A: Given P= 301 lb

Q: Date: water is contained behind a semi circular gate, AB with radius of R= 2 m- The By neglecting…

Q: If the magnitude of the resultant force acting onthe bracket is to be 80 lb directed along the u…

A: Given :- Magnitude of the resultant force acting on the bracket along the u axis = 80 lb To…

Q: Two cables are tied together at C and are loaded as shown. Knowing that P = 341 N and R = 240 N,…

A: Given P =341 N R = 240 N

Q: A cantilever beam ABis fixed at its right end and extends L out of the edge of the pool. The board…

Q: To support the tent, the tension in the rope AB must be 35 lb. What are the tensions in the ropes…

Q: Situation 9. To support the tent, the tension in the rope AB must be 35 lb. What are the tensions in…

A: Tension in the rope AB, TAB = 35 lb To find TAC, TAD, TAE where TAB, TAD, TAE are tension in ropes…

Q: Determine the vertical and horizontal reactions of the hinge support if the weight of M object is FN…

A: Determine the vertical and horizontal reactions of the hinge support?

Q: 3-39. A "scale" is constructed with a 4-ft-long cord and the 10-lb block D. The cord is fixed to a…

A: tanθ=0.51.5 ⇒θ=18.43°On resolving force on point DFy=0mass of block D = tension in string CD…

Q: d.2mm 0.25M 204 A 0.08 0 32

A: allowablw deflection at point B=1.5 mmmodulus of the elasticity for rod CD E=200 GPA=200× 103…

Concept explainers

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.

Question

A 36-lb triangular plate is supported by three wires as shown. Determine the tension in each wire, knowing that a= 6 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Trending now

This is a popular solution!

Step by step

Solved in 8 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
26 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Ax = ?A) 30B) 18.75C) None.D) 3.75E) 0
Determine for in the member AD And BC using method of joints. (Theta=30 degree)
The rigid bar AD is supported by two steel wires of 116-in. diameter (E529 3 106 psi) and a pin and bracket at A. Knowing that the wires were initially taut, determine (a) the additional tension in each wire when a 220-lb load P is applied at D, (b) the corresponding deflection of point D
If P= 8.571 kN, Determine the stress in member CEassuming that the area in steel is 24 mm2.Show FBD
Given: fy = 345 Mpaf'c = 28 Mpa Determine the moment arm of the beam in mm in 3 decimal places.
If the bucket weighs 50 lbs, determine the tensions developed in each of the wires. The angle for wire BC and DE is 30deg and a slope of 4 vertical, 3 horizontal for wire BE. Find the tension at wire Fb, tension at wire Fd, tension at wire Fc and tension at wire Fa.
Determine the nominal moment strengt of the irregular beam shown. Assume the area of 25 mm rebar is 510 sq. mm. Given: a.) fc' = 35 MPa; fy= 413.70 MPa b.) fc' = 21 MPa; fy = 413.70 MPa
Solve the problem completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Design the number of 36 mm diameter bars to support the maximum positive moment of Mu=1600 kN.m. Use f'c=28MPa, fy=345MPa, h=800mm, bf=1000mm, bw=400mm, flange thickness=100mm, stirrups=10mm, and cc=40mm. Calculate the effective depth of the final section in mm.0 Calculate the depth of the compression block of the final section in mm.0 Calculate the depth of the neutral axis of the final section in mm.0 Calculate the ultimate moment capacity of the final section in kN.m.0
Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
Determine the slope at the roller B of the double overhang beam shown. Take E = 200 GPa, I = 18(106) mm4.
(G) Using these results (δ1=0.1097 in. , δ2=0.1265 in. , δ3=0.0548 in.) determine the deflections of Joint B and Point D. ANSWERS in inch (H) On a piece of paper, sketch a free body diagram (FBD) cut through rod (3) and also a FBD of the rigid bar. Using these, find a relationship between the force in rod 1 (F1) and the applied load, P, a relationship between the force in rod 2 (F2) and the applied load, P, and also a relationship between the force in rod 3 (F3) and the applied load, P. (I) Based on the allowable stress for the bronze, calculate the maximum allowable force that can be supported by rod (1), and the corresponding maximum value for the applied load P. IN KIPS (J) Based on the allowable stress for the aluminum, calculate the maximum allowable force that can be supported by rod (2) and rod 3, and the corresponding maximum value for the applied load P. IN KIPS (K) Using the results from Part 8, determine the deflections of Joint B and Point D. IN INCH NOTE: These are the…