A 3D solid component is subject to external forces such that following three principal stresses are generated: -51MPa, 207MPa and. -327.87MPa. The component is made from a ductlie metal with a Yield Strength of 400MPa Determine for an element of stress subject to these stresses: the Maximum Shear Stress (Answer in MPa only). the Octohedral Shear Stress (Answer in kPa only). the Hydrostatic Stress (Answer in Pa only). the Tresca Effective Stress (Answer in MPa only). the von Mises Stress (Answer in Pa only) Select the 5 correct answers from the list below/:

A 3D solid component is subject to external forces such that following three principal stresses are generated: -51MPa, 207MPa and. -327.87MPa. The component is made from a ductlie metal with a Yield Strength of 400MPa Determine for an element of stress subject to these stresses: the Maximum Shear Stress (Answer in MPa only). the Octohedral Shear Stress (Answer in kPa only). the Hydrostatic Stress (Answer in Pa only). the Tresca Effective Stress (Answer in MPa only). the von Mises Stress (Answer in Pa only) Select the 5 correct answers from the list below/:

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Similar questions

A 10000N tensile force is used to pull a cylindrical rod with an initial diameter of 2 cm. During the pull, the rod's diameter decreases to 1.8 cm. What is the true stress?I will rate accordingly...
Sketch a tensile member with (a) a rectangular crosssection, (b) a solid circular cross section, and (c) a circulartubecross section, and label the dimensions symbolically (e.g.,label the radius for the solid circular case). For each member, write out the definition of engineering stress in terms of the actual dimensions of the component. If therectangular member has dimensions of width and thicknessequal to 1 cm 0.3 cm, what would be the radius of a solidcircular member such that the stress is equal for an equaltensile load? If a tube has an outer radius equal to that ofthis same solid cylinder, what is the maximum inner radiussuch that the stress does not exceed 200% of the stress inthe solid cylinder?
A 10000N tensile force is used to pull a cylindrical rod with an initial diameter of 2 cm. During the pull, the rod's diameter decreases to 1.8 cm. What is the true stress?i ll rate. S
At a point in a bar of cast iron, the principal stresses are 60 MPa tensile and 120 MPa compressive whereas the third principal stress is zero. Find the factorsof safety based on the elastic limit when the criterion of failure is principal stress theory. Assume the elasticlimit of cast iron is 90 MPa in tension and 440 MPa in compression
In a plane stress condition, the components of stress at a point are sigma_{x}= 20MPa , sigma_{y} = 80MPa , Ty = 40 MPa . What is the maximum shear stress (in MPa) at the point?
Please solve this problem with the principle of Strain energy due to direct stresses MODULE IS STRENGTH OF MATERIALS 2
can you please find Normal Stress, tangential Stress and Resultant Stress
A rectangular block of material is subjected to a tensile stress of 90 N/mm2 along X axis and acompressive stress of 45 N/mm2 on a plane at right angle to it, together with shear stresses of80 N/mm2 on the same plane. Calculate the direction of principal planes, the magnitude ofprincipal stresses and the magnitude of greatest shear stresses.
hi im reviewing my class notes and im confused as to how it obtained the answer of 87.47 Mpa. P.S. this topic is stress transformation
When a thin cylinder is subjected to an internal pressure p, the tangential stress should be the criterion for determining the cylinder wall thickness. Explain.
Can you help me with this problem, please: At a material point in plane stress it is known that the hydrostatic component of the stress is 15 ksi and that the second stress invariant is 30 ksi. Determine the magnitude of the principal stresses and the maximum shear stress.
An cylinder is 30 cm in diameter and the steam pressure is 7 kg/cm. If the cylinder head is held by 12 studs, find the size, assume safe tensile stress as 280 N/mm