A 3kg block slides along a floor with coefficient of kinetic friction lk = 0.3, initially moving at 7.0m/s. It travels for 2.0 meters, then encounters a ramp sloped upward at 40°. The ramp also has a coefficient of kinetic friction lk = 0.3. How fast is the block moving when it reaches the bottom of the ramp? How far up the ramp does the block slide, before momentarily coming to rest?

A 3kg block slides along a floor with coefficient of kinetic friction lk = 0.3, initially moving at 7.0m/s. It travels for 2.0 meters, then encounters a ramp sloped upward at 40°. The ramp also has a coefficient of kinetic friction lk = 0.3. How fast is the block moving when it reaches the bottom of the ramp? How far up the ramp does the block slide, before momentarily coming to rest?

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter5: Energy

Section: Chapter Questions

Problem 36P: A block of mass m = 5.00 kg is released from rest from point and slides on the frictionless track...

See similar textbooks

Similar questions

In an iconic movie scene, Forrest Gump (https://openstaxcollege.org/l/21ForrGumpvid) runs around the country. If he is running at a constant speed of 3 m/s, would it take him more or less energy to run uphill or downhill and why?
A 100 — kg man is skiing across level ground at a speed of 8.0 m/s when he comes to the small slope 1.8 m higher than ground level shown in the following figure. (a) If the skier coasts up the bill, what is his speed when he reaches the top plateau? Assume friction between the snow and skis is negligible. (b) What is his speed when he reaches the upper level if an 80 — N frictional force acts on the skis?
As shown in Figure P7.20, a green bead of mass 25 g slides along a straight wire. The length of the wire from point to point is 0.600 m, and point is 0.200 in higher than point . A constant friction force of magnitude 0.025 0 N acts on the bead. (a) If the bead is released from rest at point , what is its speed at point ? (b) A red bead of mass 25 g slides along a curved wire, subject to a friction force with the same constant magnitude as that on the green bead. If the green and red beads are released simultaneously from rest at point , which bead reaches point first? Explain. Figure P7.20
A 6.50 102-kg elevator starts from rest and moves upward for 3.00 s with constant acceleration until it reaches its cruising speed, 1.75 m/s. (a) What is the average power of the elevator motor during this period? (b) How does this amount of power compare with its power during an upward trip with constant speed?
The system shown in Figure P5.43 is used to lift an object of mass m = 76.0 kg. A constant downward force of magnitude F is applied to the loose end of the rope such that the hanging object moves upward at constant speed. Neglecting the masses of the rope and pulleys, find (a) the required value of F, (b) the tensions T1, T2, and T3, and (c) the work done by the applied force in raising the object a distance of 1.80 m. Figure P5.43
A block of mass m = 5.00 kg is released from rest from point and slides on the frictionless track shown in Figure P5.36. Determine (a) the blocks speed at points and and (b) the net work done by the gravitational force on the block as it moves from point from to . Figure P5.36
If the net work done by external forces on a particle is zero, which of the following statements about the particle must be true? (a) Its velocity is zero. (b) Its velocity is decreased. (c) Its velocity is unchanged. (d) Its speed is unchanged. (e) More information is needed.
Review. A bead slides without friction around a loop-the-loop (Fig. P7.3). The bead is released from rest at a height h = 3.50R. (a) What is its speed at point ? (b) How large is the normal force on the bead at point if its mass is 5.00 g? Figure P7.3
A large cruise ship of mass 6.50 107 kg has a speed of 12.0 m/s at some instant. (a) What is the ships kinetic energy at this time? (b) How much work is required to stop it? (c) What is the magnitude of the constant force required to stop it as it undergoes a displacement of 2.50 km?
A particle moves in one dimension under the action of a conservative force. The potential energy of the system is given by the graph in Figure P8.55. Suppose the particle is given a total energy E, which is shown as a horizontal line on the graph. a. Sketch bar charts of the kinetic and potential energies at points x = 0, x = x1, and x = x2. b. At which location is the particle moving the fastest? c. What can be said about the speed of the particle at x = x3? FIGURE P8.55
A block of mass 0.500 kg is pushed against a horizontal spring of negligible mass until the spring is compressed a distance x (Fig. P7.79). The force constant of the spring is 450 N/m. When it is released, the block travels along a frictionless, horizontal surface to point , the bottom of a vertical circular track of radius R = 1.00 m, and continues to move up the track. The blocks speed at the bottom of the track is = 12.0 m/s, and the block experiences an average friction force of 7.00 N while sliding up the track. (a) What is x? (b) If the block were to reach the top of the track, what would be its speed at that point? (c) Does the block actually reach the top of the track, or does it fall off before reaching the top?
A child of mass m starts from rest and slides without friction from a height h along a curved waterslide (Fig. P5.46). She is launched from a height h/5 into the pool. (a) Is mechanical energy conserved? Why? (b) Give the gravitational potential energy associated with the child and her kinetic energy in terms of mgh at the following positions: the top of the waterslide, the launching point, and the point where she lands in the pool. (c) Determine her initial speed V0 at the launch point in terms of g and h. (d) Determine her maximum airborne height ymax in terms of h, g, and the horizontal speed at that height, v0x. (e) Use the x-component of the answer to part (c) to eliminate from the answer to part (d), giving the height ymax in terms of g, h, and the launch angle . (f) Would your answers be the same if the waterslide were not frictionless? Explain. Figure P5.46