A 3x3m plate at 500 degC is suspended vertically in a very large room. The plate has an emissivity of 0.13, The room is at 25degC. What is the net heat transfer from the plate?
Q: The block in the figure has a weight of 400 lb and an applied force of 600 lb to the right. There is…
A: Given, let's take x axis along inclined plane and y axis perpendicular to the inclined plane as…
Q: 18. Small welding shops generally wire their power sources to what voltages? O A. 220 V/AC O B. 480…
A: For general arc welding processes, we require normal voltage and current at the input and high…
Q: Determine the magnitude and direction with respect to the +x-axis on the reaction at A and at C.…
A: For the given figure, a 2.4 kN-m moment and a 3 kN load ia acting. It is required to determine the…
Q: Provide the diagram for the problem. Choose the correct answer and provide complete solution.…
A: given; height(h1)=500ft =152.4mheight(h2)=250ft…
Q: 2. The center diagonal of the truss in the figure shown can support tension only. Compute the for DG…
A: To find force in member DG and BE
Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…
A:
Q: if the elongation of wire BC is 0.30mm after the force P is applied, determine the magnitude of P.…
A:
Q: What is the difference between vernier caliper and micrometer caliper?
A: A sliding scale that has been partitioned so that the distance between two marks on this scale is…
Q: At the beginning of compression in an ideal dual combustion cycle, the working fluid is 1 lb of air…
A:
Q: A homeowner wants to reduce their monthly heating bill and carbon footprint and is considering…
A:
Q: 26-A 40-kg block is placed on the uniform 10-kg beam, that is supported by the cable, which is…
A: Given:Mass of the block, mb=40 kgMass of the cantilever beam, mc=10 kgCoefficient of static…
Q: Strain Stress Surface tension Temperature Time Torque Velocity Viscosity (dynamic) Viscosity…
A:
Q: langed steel cantilever beam with riveted bracket is subjected to the couple and two forces shown,…
A: To find equivalent couple and resultant
Q: A horizontal pipe having a surface temperature of 67 °C and diameter of 20 cm is buried at a depth…
A: The given data in the problem is listed in the following attached image:
Q: 4. Determine the resultant force of the system shown below. 224 lb 200 lb 12 390 lb 300 lb X
A:
Q: The piston/cylinder device contains 0.4 kg of water at a temperature of 180 °C and pressure of 0.8…
A:
Q: Determine the magnitude and direction with respect to the +x axis on the reaction at A and at C.…
A:
Q: professional development hours. Examples of professional development hours include select four):…
A:
Q: Particle 1 is subjected to an acceleration a = -kv, particle 2 is subjected to a = -kt, and particle…
A:
Q: An inertial measurement unit (IMU) measures the following quantities? Select all statements that are…
A: Inertial measurement unit (IMU) is an electronic component which uses a combination of…
Q: Q1: Select the correct answer. ( A. Resilience is the energy absorbed by the material up to a.…
A: According to the guidelines, I can solve only first three subparts. For rest problem, repost in a…
Q: The graph below represents the distance-time relationship from Justin and Nicole as they cycled on a…
A: Given question provides us with a graph that represents the variation of position of two cyclists…
Q: In an archery test, the acceleration of the arrow decreases linearly with distances from its initial…
A:
Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…
A: Given data, F1=10 kN F2=40 kN F3 = 35 kN F4=40 kN M = 105 kNm Since, all the triangles are in the…
Q: The resultant of three concurrent forces A, B, and C is 10N with directions ?? = 60°, ?? = 60°, ?? =…
A:
Q: Draw a hard sphere unit cell representation of a body centered cubic (BCC) crystal and derive the…
A: Body-Centered Cubic (BCC): A body-centered cubic structure consists of atoms arranged in a cube…
Q: The displacement of a particle is given by s = 4t³-48t² + 80t -63 where s is in feet and t is in…
A: Write the expression of displacement. s=4t3-48t2+80t-63
Q: please put it on paper. thank you
A:
Q: Blocks A, B, C, and D have weights of 50 N, 25 N, 20, and 15 N, respectively as shown in Fig.3. All…
A: GivenWA=50NWB=25NWC=20NW=15Nμs=0.3
Q: An experimental device imparts a force of magnitude F = 36 lb to the front edge of the rim at A to…
A:
Q: 23- Blocks A, B, C, and D have weights of 50 N, 25 N, 20, and 15 N, respectively as shown in Fig.3.…
A: given; weight of block A(wA)=50Nweight of block B(wB)=25Nweight of block C(wC)=20Nweight of block…
Q: Q1/ Choose the correct answer (True or False) False O True AutoCAD provides nine ways to draw an arc…
A:
Q: How far from A, in m, is the location of the vertical component of the resultant hydrostatic force…
A: Givenρ=0.88kg/m3hemisphrical dome ABC
Q: How do you find the cross-sectional area of a trapezoid? The answer is 684 ft^2 V 1 15 ft 20 ft 18…
A:
Q: determine the normal and tangential components of the boat acceleration at s=16ft
A: Normal acceleration:- Normal acceleration is the rate of change of direction of any particle in…
Q: In thehydroelectric power plant, water enters the turbine nozzles at 700 kPa absolute witha low…
A:
Q: The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as…
A:
Q: so is the answer a, b, c, or d?
A:
Q: Saturated air at 15°C flows to a heater at the rate of 0.76 m³/s. Heat is transferred to the air at…
A: Write the properties of saturated air at 15 oC. h=cPT=1.005283=284.415 kJ/kgAnd,ρ=1.2 kg/m3
Q: Example-1:- V A rigid tank with a volume of 1.8 m3 contains 15 kg of saturated liquid- -: vapor…
A:
Q: Which of the following statements is/are true? 1. The force per unit area, or intensity of the…
A: Stress is defined as the ratio of force applied to the body to the cross sectional area of the…
Q: The bell-crank mechanism shown in the figure is in equilibrium. Determine (1) the normal stress in…
A: Given:Diameter of the pin at B, d=8 mmThickness of the bracket, tb=6 mmThickness of the crank, tc=10…
Q: One end/side of the pipe is positioned on level (h1) and the other is tilted upward at a height…
A:
Q: 2. Air is enclosed by a rigid cylinder containing a piston. A pressure gage attached to the cylinder…
A: GivenP1g=25psiPatm=14.7psiprocess isothermal V2=13V1
Q: - Neglecting friction forces, and the radius of the pulley. Determine the following: 1- The tension…
A: Given:Force acting on the cantilever veam ,F=140 N
Q: Steam is throttled to 0.15 MPa, 140 °C. What is the quality of throttled steam if its pressure is…
A:
Q: The equilateral triangle gate shown is hinged at the bottom along one of its edge. Which of the…
A: The relative location of the y- coordinate of the center of pressure is below point B. Point B is…
Q: A 20 kg/s steam enters a turbine at an initial enthalpy of 2456kJ/kg and exits at 1987 kJ/kg. If the…
A:
Q: Four people are attempting to move a stage platform across the floor. If they exert the horizontal…
A: The given data in the problem is shown in the following attached image:
Q: A sprinter reaches his maximum speed in 2.2 seconds from rest with constant acceleration. He then…
A:
Step by step
Solved in 2 steps with 1 images
- A spherical communications satellite, 2 m in diameter, is placed in orbit around the earth. The satellite generates 1000 W of internal power from a small nuclear generator. If the surface of the satellite has an emittance of 0.3, and is shaded from solar radiation by the earth, estimate its surface temperature.The interior wall of a large, commercial walk-in type meat freezer is covered under normal operating conditions with a 2-cm thick layer of ice. One day, a power outage cuts electricity to the refrigeration system of the freezer. Estimate the time required to melt this layer of ice if it has a mass density of 700kg/m3 and a latent heat of fusion of 334 kJ/kg. Consider the air temperature inside the freezer to be 20C with a heat transfer coefficient of 2W/m2K for convection from the freezer surface to air, and clearly state the assumptions made in your calculations.2.43 A turbine blade 6.3 cm long, with cross-sectional area and perimeter , is made of stainless steel . The temperature of the root, , is . The blade is exposed to a hot gas at , and the heat transfer coefficient is K. Determine the temperature of the blade tip and the rate of heat flow at the root of the blade. Assume that the tip is insulated.
- 3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.1.67 In beauty salons and in homes, a ubiquitous device is the hairdryer. The front end of a typical hairdryer is idealized as a thin-walled cylindrical duct with a 6-cm diameter with a fan at the inlet that blows air over an electric heating coil as schematically shown in the figure. The design of this appliance requires two power settings, with which the air blown over the electric heating coil is heated from the ambient temperature of to an outlet temperature of and with exit air velocities of 1.0 m/s and 1.5 m/s. Estimate the electric power required for the heating coil to meet these conditions, assuming that heat loss from the outside of the dryer duct is neglected.One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
- 8.15 A mercury bath at is to be heated by immersing cylindrical electric heating rods, each 20 cm tall and 2 cm in diameter. Calculate the maximum electric power rating of a typical rod if its maximum surface temperature is .The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specifiedAn electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
- The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of 1.9cm1.25cm mild steel bar stock. To reduce the grip temperature, it is proposed to form the handle of tubing 0.15 cm thick to the same rectangular shape. If the average heat transfer coefficient over the handle surface is 14 W/m K, estimate the reduction of the temperature at the grip in air at 21C.3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.Using Table 1.4 as a guide, prepare a similar table showing the orders of magnitude of the thermal resistances of a unit area for convection between a surface and various fluids.