Ans[ 0.372]Q20/A 4-pole, 3-phase, 50 Hz, slip-ring induction motor rotates at 1440 r.p.m. With slip-ring terminalsshort-circuited. The rotor resistance is 0.1 2/phase and standstill reactance/phase is 0.6 2. If anexternal resistance of 0.1 2/phase is added to the rotor circuit, what will be the new full-loadspeed?Ans[ 1380 r.p.m.]

Answered: Image /qna-images/answer/9793897a-2ddd-49a9-97cf-3878ee89a074.jpg

Answered: A 4 1 4-pole, 3-phase, 50 Hz, slip-ring…

A 4 1 4-pole, 3-phase, 50 Hz, slip-ring induction motor hort-circuited. The rotor resistance is 0.1 Ophase xternal resistance of 0.1 /phase is added to the peed?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 25 HP, 6 pole, 50 Hz, 3-phase slip ring induction motor runs at 960revolutions per minute on full load with a rotor current per phase of 35 A.Allowing 250 W for the copper loss in the short-circuiting gear, and 1000Wfor mechanical losses, find the resistance per phase of the three-phaserotor winding.
A three phase, 4 pole, 3300 V, 50 Hz, star connected Induction motor, has identical primary and referred secondary impedance of value 3+j9 Ohm per phase. Using the approximate circuit, calculate: A. The full load torque at rated slip of 5%. B. The maximum torque at normal voltage and frequency.
The full-load slip of 4-pole,60Hz,440v (line -to-line) three phase induction motor is 0.05. i.What is the speed of the rotating stator field?What is the frequencey (in Hz) of the rotor current. ii.When the output power of the motor is 90 hp at a speed of 1732rpm,rotational losses(which includes frictional and core losses) are 10,100W,while copper losses for both rotor and stator total 3700W.Determine the motor efficiency and line current,assuming the motor has a 0.8 pf lagging under these conditions.
The full load slip of a 4-pole, 60Hz, 440V (line-to-line) three phase induction motor is 0.05. (i). What is the speed of the rotating stating? What is the frequency (in Hz) of the rotor current? (ii). When the output power of the motor is 90 hp at a speed of 1732 rmp, rotational losses (which include frictional and core losses) are 10,100W, while copper losses for both the rotor and stator total 3700W. Determine the motor efficiency and line current, assuming the motor has a 0.8pf lagging under the conditions.
18. A single-phase, 120 V, 60 Hz, four-pole, split-phase induction motor has the following standstill impedances:Main winding: Zm =5+j6.25Auxiliary winding: Za =8+j6a) Determine the value of capacitance to be added in series with the auxiliary winding to obtain maximum starting torque.b) Compare the starting torques and starting current with and without the added capacitance in the auxiliary winding circuit when operated from a 120V, 60Hz supply.
Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please
A 3300-V, 50-Hz, 3-phase, 4-pole, star-connected induction motor has identical primary and referred secondary impedances of value 3 + j9 ohm per phase. The turns-ratio per phase is 3/I (stator/rotor), and the rotor winding is connected in delta and brought out to slip rings. Calculate: the full-load torque at rated slip of 5%; the maximum torque at normal voltage and frequency; the supply voltage reduction which can be withstood without the motor stalling; the maximum torque if the supply voltage and frequency both fall to half normal value; the increase in rotor-circuit resistance which, at normal voltage and frequency, will permit maximum torque to be developed at starting. Express this: as a fraction of normal R2and as (3) ohmic values to be placed in series with each of the slip-ring terminals and star connected.
A 3-phase 9-pole,50Hz, star connected induction motor has an emf 520 V(L-L). The stator winding has a synchronous reactance of 2.5 Ohms/phase. Induction machine operates at rated voltage and at a leading power factor of 0.85. Shaft power is 15 Kw and the excitation emf is 500 V. (a). Determine the load angle, armature current in per unit and the power factor of the alternator. (b). The alternator is now made to operate at another value of excitation emf which results in the same values of power output and armature current. Under these conditions, find the excitation voltage, load angle and the power factor. (c) If the excitation in (a) and that obtained in (b), which is more likely to be used in practical situations and and why? (d) With the alternator output remaining constant, the alternator excitation is increased by 15%. Find the new values of armature current, load angle and pf? (e) Calculate the total steam output of the alternator delivered to the prime mover? (f) Draw the…
A 4-pole, 3-phase, 50Hz induction motor has a voltage between slip-rings on open circuit of 520V. The star connected rotor has a standstill reactance and resistance of 2.0 and 0.4 Ω per phase respectively. Determine: (a) The full-load torque if full load speed is 1,425 rpm(b) The ratio of starting torque to full-load torque(c) The additional rotor resistance required to give maximum torque at standstill.
A 3-phase 440V, wye connected induction motor has a star-connected stator and delta connected rotor with a turns ratio of 10. The rotor resistance and standstill reactance per phase are 0.01Ω and 0.2Ω respectively, what should be the value of external resistance (in Ω) that must be inserted to the rotor circuit in order to obtain maximum torque at starting?
A 380V 50Hz Δ-connected induction motor, its R2=2.5Ω, and I2=25A. For a rotor slip of 3% at rated conditions, Pconv equal:
A three-phase induction motor, operating at rated voltage and frequency, has a startingtorque of 1.35 times and a maximum torque of 2.2 times, both with respect to its rated-loadtorque. Ignoring the effects of the stator resistance and rotational losses and assumingconstant rotor resistance, determine the slip rated load, and the rotor current at starting (as a percentage of the rotor current at rated load). The slip at maximum torque is 0.343 if that helps.