A 4 module, 20◦ pinion of 36 teeth drives a gear of 72 teeth.  a. Calculate the length of action and contact ratio if the gears in mesh with zero backlash. b. If the center distance is increased 0.8mm,calculate the radii of the operating circles, operating pressure angles  and backlash produced. c. Check if interference occurs

Q: Determine the magnitude of the resultant force R (in N) to replace the force system in the given…

A:

Q: Problem 2. If a force of P = 100 N is applied to the handle of the toggle clamp, determine the…

A: Given data  P= 100N  Find the horizontal force on smooth wooden Block E

Q: If a powertrain was being tested using a scan tool and a diagnostic trouble code (DTC) P0503 was…

A: Powertrain: Powertrain is a gear train which is operated by engine so the power is given to the…

Q: Question A 1.2 m x 1.2 m square gate located in the vertical side of an open tank is pivoted about…

A: “Since you have posted multiple questions with multiple sub-parts, we will provide the solution only…

Q: Find the magnitude and depth of the point of application of the force on circular gate shown in…

A: Given data  h=5 ft And diameter D=4 ft Find the force F and location of force

Q: how did you find the equation for L in step 2 and also why isnt h mulplied by the Area when solving…

A:

Q: Explore the profile of a cylindrical cam to give uniform velocity during outstroke of 25 mm to its…

A: The profile of a cylindrical cam to achieve the desired motion can be created by defining the…

Q: A two storey building has two faucets, one in the basement and one in the first floor. The maximum…

A: Givenρ=1000 kg/m3V=13m/sd=1.5cm=0.015m

Q: Using graphical method solve this problem:  Suppose you first walk A in a direction of B west of…

A:

Q: The accepted resistivity value at room temperature for copper wire is 1.7421 x 10-8 ohm meter.…

A: To find: The resistivity and the percentage error. Given: The resistivity at room temperature for…

Q: Find the dynamic viscosity of i) 50°F water ii ) 140°F water (in BG units) What is the ratio of the…

A: Given data: case 1 - Temperature =  50 deg.F case 2 -  Temperature = 140 deg.F   To find: a. dynamic…

Q: Use blank or isometric grid paper to draw the isometric views of the following objects.

A: Draw the given three views.

Q: A certain gas was produced as a product of a decomposition reaction in a reactor vessel. The…

A: The given information in the problem is shown in the following attached image:

Q: The roller coaster car has a mass of 900 kg, including its passenger. It is released from rest at…

A: Givenm=900kghB=19mρB=9.5mhC=14mρC=7m

Q: Problem 1. The structure shown below supports a 100 N load. Note that the structure consists of…

A:

Q: 5. What weight W is necessary to start the system of blocks shown in the figure moving to the right?…

A: The coefficient of friction is μ=0.1. The pulleys are frictionless.

Q: The motorcycle is traveling at 45 m/s when it is at A. The speed is then decreased at i-(0.058)…

A:

Q: A 3D truss is supporting 2 forces F₁ and F2. F₁ = 1,080 N at and angle alpha= 33 deg. F1 is in the…

A:

Q: The tower crane is used to hoist a 2.0-Mg load upward at constant velocity as shown in (Figure 1).…

A:

Q: Explore the profile of a disc cam to give uniform velocity during outstroke of 25 mm to a knife edge…

A: Given: Diameter of the shaft→D=25 mm Length of the stroke→L=25 mm Axis of the follower are passing…

Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…

A: According to the data a structure is ABC is provided with the loading as shown in the figure  We…

Q: Determine the outside diameter of a hollow steel rod that will carry a tensile load of 55,000 kg at…

A: This question is based on the concept of stress from strength of material.

Q: Boxes are transported by a conveyor belt with a velocity vo to a fixed incline at A where they slide…

A: In this problem, we will calculate the velocity of the conveyor belt when the velocity of the box is…

Q: Explain the function and operation of variable valve timing. (10 - 20 words)

A: According to the question we need to explain the function and operation of variable valve timing

Q: The aluminum rod AB (G=27 GPa) is bonded to the brass rod BD (G-39 GPa). Knowing that portion CD of…

A: In this problem, we will calculate the angle of the twist at A, for the calculation of the angle of…

Q: A machine of mass 112.7 kg is mounted on four parallel springs each of stiffness 3.2 x 10³ N/m. When…

A:

Q: The steel railroad increases its length when exposed to heat from 70°F to 95°F. The coefficient of…

A: Given data  T1=70°F and T2= 95°F Thermal expansion coefficient = 11.7 ×10-6 (m/m°C) Find the strain

Q: 2. A 40 kg block is at rest on the slope when a force F is applied to it. Determine the magnitude of…

A: Mass of block = 40kg Find the force F is the velocity is 5m/s at t=2sec

Q: Describe the environmental best management practice for trapping, storing and disposal of fluids…

A: The disposal of fluids from diesel engines refers to the process of safely disposing of the various…

Q: 1. From the diameter of the sun and the earth and the mean distance of sun from earth, estimate (a)…

A: “Since you have posted multiple questions with multiple sub parts,we will provide the solution only…

Q: A 14 m cantilever beam has a concentrated load of 25 kN at the mid- span. Find the maximum slope of…

A:

Q: Consider (Figure 1) with F₁ = 260 N and F2 = 170 N. Resolve F₁ into components along the u and…

A: Calculated components of F1 along the u and v axes in N.

Q: Determine the magnitude R of the resultant of forces shown in figure and the angle of 0, between x-…

A: According to the given data Four forces are given  We need to find  Resultant and the line of…

Q: Determine the moment of inertia of the given shapes

A: Given: The given figure contains two rectangle. Width of outer rectangle (b1)=325 The length of…

Q: (A) For Problem 3.17, without changing the total length of the shaft, where would you move Point B…

A: For solution refer below images

Q: A 3380-lb car is traveling with a speed of 56 mi/hr as it approaches point A. Beginning at A, it…

A:

Q: Indicate all Zero-force members. Determine the force in members CD and CM of the Baltimore bridge…

A: The "zero-force members" in a truss refer to the members that are not carrying any load and are only…

Q: Wedges A and B are shown in the figure. Assume the coefficient of friction between A and B is 0.2…

A:

Q: Determine the moment exerted by cable AB about point O. The force in the cable is 1 kN.

A:

Q: Explain the operation of blind spot monitoring as part of lane keeping assist. (50 - 70 words)

A: Blind spot: Blind spot is the dip or irregular surface on the road on both sides of the vehicle and…

Q: 3-2. The members of a truss are pin connected at joint O. Determine the magnitude of F₁ and its…

A:

Q: 1. The motor M is connected to the speed reducer C by the tubular shaft and compling. The shaft has…

A: The given values are -  do= 1inch =25.4 mm, di= 0.75 inch =19.05 mmτallow  = 12 ksi =82.74 MPa P =…

Q: Identify two (2) mechanical components that are most likely to cause abnormal noises in a diesel…

A: To identify: The mechanical component that causes abnormal noises.

Q: Problem No.1: Find the natural torsional frequencies, the frequency Equation and Mode shapes of a…

A: To find: The natural torsional frequency, the frequency equation and mode shapes of a uniform rod.…

Q: Air enters a circular conduit at a pressure of 105 kPaa and leaves at an outlet pressure of 108…

A:

Q: *2-4. The vertical force F acts downward at A on the two- membered frame. Determine the magnitudes…

A:

Q: A 6-x 10-in. timber beam has been strengthened by bolting two - x 2-in. steel straps to it as shown…

A: Given: Modulus of elasticity of the wood: →E1=1.5×106 psi Modulus of elasticity of the steel:…

Q: A homogeneous, 4-ft-wide, 3.1-ft-long rectangular gate weighing 800 lb is held in place by a…

A:

Q: What is U3003:16 the diagnostic trouble code (DTC) for? What system component sets the U3003:16 DTC?…

A: Given: Vehcile- 2016 ND Mazda MX5

Q: A Based on observations, the speed of a jogger can be approximated by the relation v = 6.4 (1 −…

A: Given data: v = 6.4×(1-0.03x)0.4 (note: the given data format is corrected accordingly) x = 0 when…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.