A 400 km overhead transmission line delivers a load of 100 MVA at 132 kV, 60 Hz and 0.8 pf lagging. Resistance of the line is 35.5 N, reactance is 72.5 N and admittance due to the charging capacitance is 0.551x 10-3 mho. Calculate; a) A, B, C, D constants b) Sending end power factor c) Voltage regulation

A 400 km overhead transmission line delivers a load of 100 MVA at 132 kV, 60 Hz and 0.8 pf lagging. Resistance of the line is 35.5 N, reactance is 72.5 N and admittance due to the charging capacitance is 0.551x 10-3 mho. Calculate; a) A, B, C, D constants b) Sending end power factor c) Voltage regulation

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.52P

See similar textbooks

Similar questions

A 3-phase, 50 Hz overhead transmission line, 100 km long, 110 kV between the lines at the receiving end has the following constants : Resistance per km per phase = 0·153 W Inductance per km per phase = 1·21 mH Capacitance per km per phase = 0·00958 µF The line supplies a load of 20,000 kW at 0·9 power factor lagging. Calculate using nominal p representation, the sending end voltage, current, power factor, regulation, and the efficiency of the line. Neglect leakage.
A 210 km long three-phase transmission line is operated on a 60 Hz network. Line Finally a 40 MVA power with 0.78 back power factor under 120 kV voltage is being shot. The conductor resistance value of the line is 0.10 Ω / km, the inductance value Since 1.30 mH / km and capacitance value is 0.001 µF / km, Medium Transmission Line establishing the equivalent circuit model; a) -Calculate the line current and voltage of the sending side. b) Calculate the power loss on the line. c) Calculate the% voltage regulation value of the line.
A 30 mile, 3-phase transmission line delivers 8,000 kW at 33 kV, p.f. 0.8 lagging. The resistance and reactance of single conductor are 0.6 ohm and 0.72 ohm respectively per mile. Find the percent efficiency of the line.
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…
In the power system whose single line diagram is shown below, the line cross section is 95 mm2, the intrinsic conductivity coefficient is 34m/ohm.mm2 and the inductive reactance of the line is given as 0.4 ohm/km. According to these values; a) Calculate the active, reactive and visible components of the currents passing through each line segment.b) Find the location and value of the largest voltage drop.
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
A 3-phase, 50 Hz overhead transmission line, 100 km long, 110 kV between the lines at the receiving end has the following constants : Resistance per km per phase = 0·153 Ω Inductance per km per phase = 1·21 mH Capacitance per km per phase = 0·00958 μF The line supplies a load of 20,000 kW at 0·9 power factor lagging. Calculate using nominal π representation, the sending end voltage, current, power factor, regulation and the efficiency of the line
A balanced load of 30MW is supplied at 132 kV, 50Hz and 0.85 p.f. lagging by means of a transmission line. The series impedance of a single conductor is (20+j 52) ohms and the total phase-neutral admittance is 315 micro mho. Shunt leakage may be neglected. Using the nominal T and π approximation, calculate the line voltage at the sending end of the line. If the load is removed and the sending end voltage remains constant, find the percentage rise in the voltage at the receiving end.
a)We have a two-wire overhead transmission line, powered by a constant voltage source of 700 V. The values for the inductance of the conductors are 2.348x10-3 H/km and the capacitance values are 6.325x10-9 F/km. Assuming an ideal (no loss) line and its length at 130 km, determine the natural impedance of the line. b) What is the transient phenomenon in a transmission line? As an example of its causes.
A dc transmission facility is modeled by the approximate series circuit shown below. If the load voltage is known to be Vload= 458.3 kilovolt (kV) what is the power loss in the line in megawatt (MW)?
How do distributed energy resources (DERs) such as solar panels and wind turbines impact the operation and planning of power systems? Analyze their integration challenges.
A 132 KV line with 2 cm diameter conductors is built so that corona takes place if the line voltage exceeds 210 KV (rms). If the value of the potential gradient at which ionisation occurs can be taken as 30,000 Volts/cm , find the spacing between the conductors