A 3-phase, 50 Hz, 45 km long overhead line supplies 525 kW at 11 kV, 0.8 p.f. lagging. The line resistance is 5.5 O per phase and line inductance is 10 mH per phase. Calculate the Reactance of the Line, Current flowing through the transmission line, Sending end voltage, Voltage regulation and Efficiency of transmission. Inductive Reactance Current flowing through the transmission line Sending end Voltage Voltage Regulation of Transmission line Transmission line efficiency

A 3-phase, 50 Hz, 45 km long overhead line supplies 525 kW at 11 kV, 0.8 p.f. lagging. The line resistance is 5.5 O per phase and line inductance is 10 mH per phase. Calculate the Reactance of the Line, Current flowing through the transmission line, Sending end voltage, Voltage regulation and Efficiency of transmission. Inductive Reactance Current flowing through the transmission line Sending end Voltage Voltage Regulation of Transmission line Transmission line efficiency

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.11P: A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of...

See similar textbooks

Similar questions

A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
A single-phase overhead transmission line consists of two solid aluminum conductors having a radius of 3 cm with a spacing 3.5 m between centers. (a) Determine the total line inductance in mH/m. (b) Given the operating frequency to be 60 Hz, find the total inductive reactance of the line in /km and in/mi. (c) If the spacing is doubled to 7 m, how does the reactance change?
A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated distribution feeder. The load can be mode led by an impedance of ZL=(4.7+j9)/phase, wye-connected. The impedance of the phase conductors is (0.3+j1). Determine the following by using the phase A to neutral voltage as a reference and assume positive phase sequence: (a) Line currents for phases A, B, and C. (b) Line-to-neutral voltages for all three phases at the load. (c) Apparent. active, and reactive power dissipated per phase, and for all three phases in the load. (d) Active power losses per phase and for all three phases in the phase conductors.
A single phase overhead transmission line delivers 4000 kW at 11 kV at 0·8 p.f. lagging. If resistance and reactance per conductor are 0·15 Ω and 0·02 Ω respectively,Calculate:Percentage regulation sending end power factor Line losses
470 kVA load at 12 kV. Its resistance is 7 Ω and inductive reactance is 7 Ω if the load power factor is 0.9 lagging. Determine the Current through the line , Sending end voltage , Sending end power factor , Regulation of transmission line , Efficiency of transmission line Note:please do not handwriting
A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10Megawatts at 0.8 power factor lagging, 30kV at the receiving end. If the minimum transmission line efficiency is to be limited to 96%, estimate the per phase values of resistance and inductance of the line.
A 30 mile, 3-phase transmission line delivers 8,000 kW at 33 kV, p.f. 0.8 lagging. The resistance and reactance of single conductor are 0.6 ohm and 0.72 ohm respectively per mile. Find the voltage at the sending end in kV.
A short 3-phase transmission line connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10 MW at 0.8 lagging power factor at 30 kV at the receiving end. If the minimum transmission efficiency is to be limited to 96%, estimate the per phase value of resistance and inductance of the line.
A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0•85 p.f. lagging by means of a transmission line. The series impedance of a single conductor is (20 + j52) ohms and the total phases-neutral admittance is 315 microsiemens. Shunt leakage may be neglected. Using the nominal T approximation, calculate the line voltage at the sending end of the line. If the load is removed and the sending end voltage remains constant, find the percentage rise in voltage at the receiving end.
In the power system whose single line diagram is shown below, the line cross-section is 95 mm2, the intrinsic conductivity coefficient is 34 m/ohm.mm2 and the inductive reactance of the line is 0.4 ohm/km. According to these values; Calculate the active, reactive and visible components of the currents passing through each line segment.
A three-phase transmission line is 160 km long and supplies a load of 12 MW at 0.85 powerfactor lagging at 80 kV, 50 Hz. Each conductor has a resistance of 0.275 Ω / km, an inductivereactance of 0.5625 Ω / km and a capacitance to neutral of 0.008625 µF / km. Calculate the line-to-line sending end voltage and the sending end current, using: i. The nominal T method.ii. The nominal Π method. If the sending end voltage remains constant, estimate the approximate rise in voltage at thereceiving end when the load is switched off. Hence calculate the per unit voltage regulation ofthe transmission line.
In the power system whose single line diagram is shown below, the line cross section is 95 mm2, the intrinsic conductivity coefficient is 34m/ohm.mm2 and the inductive reactance of the line is given as 0.4 ohm/km. According to these values; a) Calculate the active, reactive and visible components of the currents passing through each line segment.b) Find the location and value of the largest voltage drop.