Answered: A 4m long brass rod subjected to an…

A 4m long brass rod subjected to an axial load of 6 kN where in the rod has a 10 mm diameter and an E = 100000 Mpa. Find its elongation

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.10.5P

See similar textbooks

Related questions

Q: 8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of…

A: Answer: The elongation of the bar will be ◆ When 30mm × 30mm square section : 2.22 mm. ◆ When 40mm…

Q: A steel rod 4m long and 20mm diameter is subjected to an axial tensile load of 45KN. Find the change…

Q: A steel rod is stretched between two rigid walls and carries a tensile load of 5000 N at 20°C. If…

A: Given: The tensile load on the steel rod is P=5000 N. The initial temperature of the rod is…

Q: A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze (E -…

Q: A steel rod 4m long and 20mm diameter is subjected to an axial tensile load of 45KN. Find the change…

Q: A 4-mm-diameter steel wire, 3.2 m long, carries an axial tensile load P. Find the maximum safe value…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

Q: Q2-B//a bar of 3m long and 25mm diameter at 70°C is gripped at ends and cooling to 30°C,the total…

Q: A hollow shaft of 25mm outside diameter and 20mm inside diameter is subjected to a tensile load of…

A: Stress: When a component or a part is subjected to any external force, a resisting force will be…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

Q: is nigidly attached between a and a bronze rod as shown in Figure 3. Axial loads are applied at the…

A: here, you not mentioned whic question's answer you want.I can give only 1 question's answer(1st…

Q: A metallic rod made of steel as shown below is used as support for a signage with length equal to…

Q: A rectangular plate 50 mm × 10 mm with a hole 10 mm diameter is subjected to an axial load of 10kN…

Q: Compute for the total elongation caused by an axial load of MN kN applied to a bar 20 mm thick…

Q: A brass rod of diameter 50mm and of length 250mm which is subjected to a tensile liad of 300kN when…

A: (a) Diameter of rod = 50 mm Area (A) = πd24Area (A) = 3.14 x 0.0524Area (A) = 0.0019625 m2…

Q: 3. A mild steel rod supports a tensile load of 50 kN. If the stress in the rod is limited to 100…

A: Given Data: Tensile load, P=50 kN Stress, σ=100 MPa

Q: A 10.0 m long with a cross sectional area 180 mm? copper rod carries a tensile load of 5 kN at 30°C.…

A: Given Data L=10 m=104 mm A=180 mm2 P=5 kN T=30°C To=20°C E=117 GPa a=17*10-6

Q: The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. Ionger than…

Q: A tensile load of 20 kN is applied on a wire made of a copper alloy having an elastic modulus of 120…

Q: A 150 inch long aluminum bar is subjected to a tensile stress of 25000 psi. Find the elongation. (E…

Q: A 14-in round wire coiled to form a conical spring with 10 effective coils & an outside diameter of…

Q: 3. A wrought iron rod is under a compressive load of 350 kN. If the permissible stress for the…

A: We are suppose to solve only one question. Please post other question as a separate question. For…

Q: 4. A steel bar of 40 mm x 40 mm square cross-section is subjected to an axial compressive load of…

A: Given, Cross sectional area = A = 40 mm x 40 mm = 1600 mm2 Axial compressive load = P = 200 kN = 200…

Q: Find the Young's Modulus of a brass rod of diameter 25 mm and of length 250 mm which is subjected to…

A: Given, Diameter of rod = d = 25 mm Length of rod = L = 250 mm Tensile load = P = 50 kN = 50 x 103 N…

Q: A Mild Steel wire 5 mm in diameter and 1 m long. If the wire is subjected to an axial tensile load…

A: Given, Diameter of wire = d = 5 mm Length of the wire = L = 1 m = 1000 mm Load = P = 10 kN = 10,000…

Q: A hollow cylinder 2 m long has an outside diameter of 50 mm and inside diameter of 30 mm. If the…

A: According to Hooke's Law, Stress is directly proportional to the strain up to a certain point. After…

Q: A steel rod of 30 mm diameter is subjected to a 10 kN of axial load. The length of the steel rod is…

Q: A steel [E = 200 GPa] rod with a circular cross section is 9-m long. Determine the minimum diameter…

Q: A steel rod of length 10 m is subjected to a axial load of 10 kN. Calculate the elongation of the…

A: Given data Length of steel rod (L) = 10 m Axial load (P) = 10 kN diameter (d) = 40 mm E = 200 GPa…

Q: 4. A steel bar of 40 mm x 40 mm square cross section is subjected to an axial compressive load of…

Q: Question 2 A rod, which tapers uniformly from 40 mm diameter to 20 mm diameter in a length of 400 mm…

Q: A steel rod having a cross-sectional area of 300 mm2 and a length of 150 m is suspended vertically…

Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…

Q: A steel bar with a cross-section 25mm x 50mm is acted upon by the axial forces as shown. What is the…

Q: The cylindrical rod is made of steel with E = 30000 ksi and u = 0.3. P 10 kips d Id = lin. L=4 ft AL…

A: Option c is correct. Here negative sign shows that final diameter is lesser than initial diameter.

Q: An aluminium alloy rod of length 1.8m and rectangular cross-sectional of area 250mm^2 is subjected…

Q: A hollow compression member with circular cross section having outer diameter 2 times the inner…

Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…

A: To find : The percentage error Given : The thickness of steel flat plate is t=10 mm. The taper…

Q: A steel rod having a cross - sectional area of 300 mm- and length of 15 m is suspended vertically…

A: Given:Area, A=300 mm2Length, l=15 m or 15000 mmLoad, P=30 kN or 30000 NY=200 GPa or 200×1000 MPa

Q: A cylindrical rod of diameter 23 mm and length 234 mm is subjected to a tensile load of 57 kN and it…

Q: 1. A 150 inch long aluminum bar is subjected to a tensile stress of 25000 psi. Find the elongation.…

Q: A steel rod is stretched between two rigid walls and carries a tensile load of 4,075 N at 20°C. If…

A: Now write the net elongation in the rod due to mechanical load and thermal load.

Q: The rigid bar ABC is supported by pin at A and aluminium wire BD, is horizontal before the Load P is…

Q: Q 2: A steel rod having a cross-sectional area of 300 mm2 and a length of 5.5 m is suspended…

A: Given data: Applied load (P) = 30 kN Cross-sectional area (A) = 300 mm2 Length of the bar (L) = 5.5…

Q: Your boss at a construction company asked you to verify the thickness of a 3 m long hollow-square…

A: Given that, Length of the column, L=3 m=3000 mmModulus of elastisity, E=200 GPA=200×103…

Q: A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of 200kN.…

Q: (a) Two vertical rods, one of steel and other of copper are each rigidly fixed at the top and 60 cm…

A: Write the expression of the cross-sectional area of the rods. Understand that the…

Q: A steel bar 40 mm x 40 mm square cross-section is subjected to an axial compressive load of 200 kN.…

A: Data given- A = 40 mm × 40 mm = 1600 × 10-6 m2 P = 200 × 103 N L = 2 m E = 200 × 109 Pa

Q: 2. Two aluminum rods AB and BC hinged to rigid supports are pinned together at 3m B to carry a…

A: load P = 20 KN Crossection area of rod = 400 mm2 modulus of elasticity E = 70,000 MPa = 70 GPa…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

A 4m long brass rod subjected to an axial load of 6 kN where in the rod has a 10 mm diameter and an E = 100000 Mpa. Find its elongation

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.
A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.
A symmetrical framework consisting of three pin-connected bars is loaded by a force P (see figure). The angle between the inclined bars and the horizontal is a = 52°. The axial strain in the middle bar is measured as 0.036. Determine the tensile stress in the outer bars if they are constructed of a copper alloy having the following stress-strain relationship:
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A prismatic bar of length L = 1.8 m and cross-sectional area A = 480 mm" is loaded by forces P{= 30 kN and A = 60 kN (see figure) The bar is constructed of magnesium alloy having a stress-strain curve described by the Ram berg-Osgood equation: 45.000 618 UW id which u has units of mega pascals (MPa). (a) Calculate the displacement 8t- of the end of the bar when the load P:acts alone. (b) Calculate the displacement when the load P, acts alone. (c) Calculate the displacement when both loads act simultaneously.
Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A prismatic bar with a length L = 1 m and cross-sectional area A = 1200 mm2 is supported at the ends. The bar is then subjected to a temperature increase ?T = 25°C. Calculate the complete stale of stress acting on an inclined section .rs that is cut through the bar at an angle ?? = 45*. Use E = 200 GPa and the coefficient of thermal expansion a = 12×10-6/?.
Repeat Problem 2.4-8, but assume that the bar is made of aluminum alloy and that BC is prismatic. Assume that P = 20 kim. L = 3 ft.t = 314 in., b1 2m.b 2.Sin.andElO.400ksi.
A steel bar of 40 mm x 40 mm square cross section is subjected to an axial tensile load of 200 kN. If the length of the bar is 2m and E=200 GPa, the elongation of the bar will be: