A brass rod of diameter 50mm and of length 250mm which is subjected to a tensile liad of 300kN when the extension of the rid is 0.10mm. Calculate: Cross-sectional area (b) Stress (c)strain (d) Young's modulus

A brass rod of diameter 50mm and of length 250mm which is subjected to a tensile liad of 300kN when the extension of the rid is 0.10mm. Calculate: Cross-sectional area (b) Stress (c)strain (d) Young's modulus

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Related questions

Q: 2. An Al alloy rod with 300 mm length and 10 mm in diameter is subjected to 5 x 10° N force at one…

Q: A steel rod is subjected to a stress of 200 MPa and has Young's modulus of 200 GPa. Calculate…

Q: This open-ended silo contains granular material. It is constructed from wood slats and held together…

A: Consider the diagram shown below for the pressure distribution on the sidewall of the silo. The…

Q: Consider the brass alloy for which the stress-strain behavior is shown in figure below. A cylinder…

A: Note: As per Bartleby guidelines only three subparts have to be solved at a time. So upload other…

Q: A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

Q: A solid cylindrical metal of 130 cm tall and 30 mm thick is centrally bored for 0.3 m, the bore…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

Q: A 35 kN axial load is applied to a metal bar with a rectangular cross-section, 28mm wide by 10mm…

A: To find: The original length of the bar. Given: The load is P=35 kN. The width is 28 mm and…

Q: From the tensile stress-strain behavior for the brass specimen , the diameter is 12-8 mm Calcalate…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

Q: 2.76 Steel railroad rails 10 m long are laid with end-to-end clearance of 3 mm at a temperature of…

Q: A rod 150 cm long and diameter 2.0 cm is subjected to an axial pull of 20 kN. If modulus of…

A: As per given question Given data Rod length =150cm Diameters =2.0cm Axial pull =20 kn Modulus of…

Q: stresses at each of three holes of 3, 5 and 10 mm diameter.

A: Given: t=15 mm To determine: The stresses at each of three holes of 3, 5 and 10 mm diameter

Q: thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of the hoop formed by…

Q: A steel disk with a 150 mm outer diameter is to be press fit to a hollow steel tube whose outer…

Q: A steel hoop. 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm. 5. Is neated and shrunk…

Q: A steel band 6mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

A: Answer: (a) The necessary increase in temperature is 52.32℃. (b) The stress occurred in the hoop is…

Q: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and shrunk onto…

Q: A steel disk with a 150 mm outer diameter is to be press fit to a hollow steel tube whose outer…

Q: A steel (E=30x106 psi) rod 10m long and 5cm in diameter is subjected to a compressive force of…

Q: A steel rod, 4 m long and 1500 mm^2 in cross-sectional area, is secured between two walls. If the…

Q: A steel circular tube is subjected to torsion by torques T applied at the ends as shown below. The…

A: This problem is related to the torsion of the shaft. torsion, when the twisting moment is applied to…

Q: 1. A rectangular plate 50 mm x 10 mm with a hole 10 mm diameter is subjected to an axial load of 10…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: A one mm diameter steel wire is wounded around a copper tube with external and internal diameters of…

A: Given: The diameter of wore, d = 1 mm The external diameter of tube, Do = 140 mm The internal…

Q: A cylindrical material that has a Young’s Modulus of 2.5 GPa that is loaded along its longitudinal…

Q: A rod 200 cm long and of diameter 3.0 cm is subjected to an axial pull of 30 kN. If the Young’s…

Q: Calculate the resulting stress in an aluminum wire, 4-m long and 2.6 mm in diameter, if a 12.5 -kg…

Q: A reinforced concrete column is constructed of 12 1-in-diameter steel rods. Calculate the force…

Q: A 23 mm diameter bronze bar 2.8 m long is placed between two rigid walls. At a temperature of -3°C,…

Q: A copper rod 6cm in diameter is placed within a steel tube, 8cm external diameter and 6cm internal…

A: Given Data The diameter of the solid copper bar is: Dcu=6 cm=60 mm The external diameter of the…

Q: A steel rod is subjected to a gradually applied load (F) which gave a rise to a maximum stress of…

A: Given: σmax=200MPaTotal length=250mm=ls-lcls=(250-lc)Total strain energy=1.3JE=200GPad=25mm To…

Q: determine the applied force F.

Q: Steel railroad rails 10 m long are laid with a clearance of 3 mm at a temperature of 15 oC. E = 200…

A: Given data: L=10 mδ=3 mmTi=15°CE=200 GPaα=11.7×10-6 °C Need to determine the temperature will the…

Q: In a sheet metal of 2 mm thickness, a hole of 10 mm diame- ter needs to be punched. The yield…

Q: A wrought iron rod is under a compressive load of 350 kN. If the permissible stress for the material…

A: Compressive load on the rod, P=350 kN=350*103 N Permissible stress for the material, σ=52.5 N/mm2

Q: A double riveted lap joint is made between 15mm thick plates. The rivet diameter and pitch are 25 mm…

Q: A circular rod of diameter 16 mm and 500 mm long is subjected to a tensile force 40kN. The modulus…

A: Given, The diameter of the rod, d=16 mm The length of the rod, L=500 mm The load, P=40 kN=40000 N…

Q: The yield stress for mild steel is 207MP.. A specimen with diameter of 0.01lm and length of 0.1m is…

Q: A single ply of a certain graphite-epoxy composite with fiber oriented at 60° is in a planer state…

A: INTRODUCTION: The principal place is considered where the principal stress is acting and the…

Q: The compressive stress developed in a metal rod (with modulus 80 GPa) when heated from 30 to 150 °C…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
A steel band 6mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of the hoop formed by the band is 29.98cm. By how much will it be necessary to increase the temperature of the hoop, so that it would slide over the surface of the cylinder? What stress will occur in the hoop when it reaches the same temperature as the cylinder, if the deformation of the cylinder may be neglected?
A bar of 7-mm in diameter is only allowed to decrease at a maximum of 1.85% of its total length. What is the maximum force (Newtons) that can be applied? Consider the shear modulus = 724 MPa, and the Poisson's ratio as 0.25.
A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The interval diameter of the hoop formed by the band is 29.98cm. By how much will it be necessary to increase the temperature of the hoop, so that it would slide over the surface of the cylinder? What stress will occur in the hoop when it reaches the same Temperature as the cylinder, if the deformation of the cylinder may be neglected?
A circular, metal rod of diameter 1 cm is loaded in tension. When the tensile load is5kN, the extension of a 25 cm length is measured accurately and found to be 0.0227cm. Calculate the tensile stress, tensile strain and estimate the value of Young’sModulus, E, of the metal.
Calculate the resulting stress in an aluminum wire, 4-m long and 2.6 mm in diameter, if a 12.5 -kg fixture is hung from the wire? Young's modulus for aluminum is 7.0 × 10^10 N/m^2. Express the answer in Pa and as a whole number.
A copper rod of diameter 10 mm and length 4 m has a tensile force of 5 kN applied on it . Modulus of Elasticity of Copper is 96 GPa. Calculate the stress in MPa and extension in mm .
A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter . The internal diameter of the hoop formed by the band is 29.98cm . By how much will it be necessary to increase the temperature of the hoop, so that it would slide over the surface of the cylinder ? What stress will occur in the hoop when it reaches the same temperature as the cylinder , if the deformation of the cylinder may be neglected ? (Write complete solution)
A compression force of 50 N applied on the round bar of 500 mm diameter, Calculate the stress induced in the bar and it's nature also.