23.) A 5-in.3 displacement motor is to be tested on a bench at 3000 rpm at 2500 lbf/in2. Assuming 100% efficiency , estimate the FHP output of the motor? 23. A 5-in.³ displacement motor is to be tested on a bench at 3000 rpm at 2500 lbf/in².Assuming 100% efficiency, estimate the FHP output of the motor?

Given data Displacement (V) = 5 in3 N = 3000 rpm p = 2500 lbf/in2 To determine FHP output of…

Answered: A 5-in.3 displacement motor is to be…

A 5-in.3 displacement motor is to be tested on a bench at 3000 rpm at 2500 lbf/in2. Assuming 100% efficiency , estimate the FHP output of the motor?

Electrical Transformers and Rotating Machines

4th Edition

ISBN:9781305494817

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Motor Nameplate Data

Section: Chapter Questions

Problem 8RQ: A motor develops 189 ft-lb of torque at 1745 RPM. What is the horse-power output of the motor?

See similar textbooks

Related questions

Q: Calculate the degree of freedom, point out the positions if there are multiple joints, high-pair and…

Q: 2. Use the method of sections to determine the forces in members AB, FG, AH, and GH. State whether…

Q: find the volume of 2.3 kg of dry staurated steam at 11000 kpa ?.

A: Given data: Mass of steam= 2.3 kg

Q: A toy rocket is launched from the top of a building 136 feet tall at an initial velocity of 162 feet…

Q: if steam at 375 kpa , having a dryness fraction of 96% , is produced from saturated water at 375 kpa…

A: Given that: P = 375 kPa x = 0.96 state 1 = saturated liquid state 2 = liquid-vapor phase at P and x…

Q: Find the value of coefficient of friction if friction force is 200 N and Normal force is 780 N

Q: The cross sectional dimensions of a beam are shown. If the flange thickness, h, is 15.5 mm,…

A: ANswer = 43.859 mm

Q: A mechanism carries a constant load P applied to the seat as E shown. Calculate the forces, in…

A: Forces in mechanisms can be calculated by balancing them in particular directions. The sum of all…

Q: Draw the kinematic diagram, indicate the number of links and joints and calculate the mobility for…

A: he term kinematic structure encompasses all those characteristics of mechanisms which are determined…

Q: Q1. An SDOF system with mass 100kg and stiffness 15kN/m is subjected to a harmonic load (120 cos18t)…

Q: 7. The rigid slab which weighs 600 kN is supported by three rods of the same cross-section and…

Q: A boiler furnace releases 10 400 kj of heat for each kg of fuel burned and produces dry staturated…

A: A boiler is a closed vessel that is used to heat water or another fluid under pressure. After that,…

Q: A worker in a children's playground is cleaning a slide with a hose. She observes that a horizontal…

Q: Consider a 150-MW steam power plant that operates on a simple Rankine cycle. Steam enters the…

Q: A mechanism carries a constant load P applied to the seat as shown. For the angle 0, determine the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: ball is fastened by a light inextensible cord 5m long to a point 3m above the level of a smooth…

Q: A model of a jet fighter aircraft of the military is to be tested in a pressurized helium wind…

A: To select the correct option.

Q: A refrigerant 22 condenser has four water passes and a total of 60 copper tubes that are 14 mm ID…

Q: A fan draws air at rest and propels it 45 meters through a rectangular duct measuring 200 by 300 mm.…

A: L=45m

Q: 1. A steel bar is 50 mm in diameter and 2000 mm long. It is surrounded by a shell of cast iron 5 mm…

A: Given Diameter, d = 50 mm Length, L = 2000 mm Thickness, t = 0.9 mm Find Load, P

Q: Given data: Force on box=12.6 N Displacement=3 m Find work done

A: Given data : Force on box=F Displacement=d Required : Work done

Q: Q2/ Determine the work done by the argon if 400-L cylinder A contain argon gas (ideal gas) at 250…

Q: An inexperienced designer of a roadbed for a new high-speed train proposes to join a straight…

A: Given data Radius of circular section = 1000 ftSpeed of train = 90 mi/hr = 90 x 1.466667 = 132 ft/s

Q: A four-cylinder, four-stroke internal combustion engine operates at 2800 RPM. The processes within…

A: Given data Speed = N = 2800 rpmP1 = 14.7 lbf/in2 = 101352.932 PaT1 = 80°F = 299.8167 KV1 = 0.03 ft3…

Q: Water at 25 deg C (998 kg/m3) flows at 10 m3/s through a straight pipe of an ID of 1.38 m to 2 m-ID.…

A: Given data Volume flow rate of water = 10 m3/s Inner diameter of pipe of section 1 = d1 = 1.38…

Q: A part of the structure for a facory automation system is a beam that spans 30.0 inches as shown…

Q: et material, containing 215% moisture (dry basis) is to be dried at the rate of 1.5 kg/sec in a…

A: Given:Temperature of air in drying medium=373 KPartial pressure of water vapor=1.4 kPaTemperature of…

Q: 2. For the beam shown: a. Draw the free-body diagram of the beam. b. Determine the reactions at the…

Q: The center of the 262-lb wheel with centroidal radius of gyration of 6.1 in. has a velocity of 3.3…

Q: PROBLEM. A mechanism carries a constant load P applied to the seat as given. As CDFE and EFGH is a…

A: Force in pin H and member FG

Q: E 100 175 400 LBE C D 150% 400 E 175 41⁰ 200 B 900 150 G H 930 800 150 200 Dimensions in millimeters…

Q: calculate the volume of 87% dry steam at 1200 kpa ?.

Q: velocity field is given by: A two-dimensional V = (x - 2y) ï- (2x + y) j a. Show that the flow is…

A: V= (x-2y) i^- (2x+y) j^

Q: Consider a 150-MW steam power plant that operates on a simple Rankine cycle. Steam enters the…

Q: Pa. Determine the COP of the cycle, if the e ic 275 kJ/kg

A: To determine COP of the cycle

Q: F9-6. The beam is subjected to the loading shown. Determine the principal stress at point C. 75 mm C…

Q: Using Work-Energy Method/Formula: If the body starts from rest at A and slides 200 ft down the 30°…

Q: 2. Determine the final Mach number and density in the compressive case with an initial Mach number…

A: Compression waves are oblique shock waves . Use compression wave concept to solve this problem

Q: The copper pipe as shown in Figure Question 4 has an outer diameter of 45 mm and an inner diameter…

Q: Find the location of the centroid of the area below. (All lengths are in mm)

Q: 1. The density of an oil is 850 kg/m3. Find its relative density (or specific gravity) and Kinematic…

A: Only one question is allowed to solve.

Q: 3. The uniform bar has a mass m and length 7. If it is released from rest when 0 = 0°, determine its…

Q: different milling cutters and indicate its uses?

A: End mills (middle row in image) are those tools which have cutting teeth at one end, as well as on…

Q: Magnitude of 23N harmonic force is acting on an undamped system with mass of 10kg and stiffness of…

Q: The hydraulic cylinder imparts a constant upward velocity VA = 0.27 m/s to corner A of the…

Q: A bar having a length of 125 mm and cross-sectional area of 467.5 mm² is subjected to an axial force…

Q: The inseminator in Fig. 8-8 contains fluid of s.g.=0.26. If the plunger is pushed in steadily at 19…

Q: Find the forces in members CD, DH, and HI. 720 N 1440 N 1440 N 720 N A 4m 4m 4m 4m B D E 3 m 1 1 16…

A: Given:

Q: The engine mechanism shown in the figure below has crank OB = 50 mm and length of connecting rod AB…

Q: Determine the equivalence ratio for the complete combustion of n-Butane (C4H10) with 50% excess air.

A: To find :- Equivalence ratio

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

23.) A 5-in.³ displacement motor is to be tested on a bench at 3000 rpm at 2500 lbf/in². Assuming 100% efficiency , estimate the FHP output of the motor?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor develops 189 ft-lb of torque at 1745 RPM. What is the horse-power output of the motor?
The length of stroke of a four cylinder four stroke cycle SI engine is1.6 times the diameter of the cylinder. The engine develops 25 kWbrake power at 2450 rpm. Each piston observes a mean effectivepressure of 8.5 bar and the mechanical efficiency is 86%. Find thediameter and stroke length of each cylinder.
In a no-load motor, a constant electromagnetic torque of 5 Nm is generated at t = 0. The engine reached 1800 revs in 4 seconds. Calculate motor inertia ignoring friction.
Indicate the differences between the rigid rotor and elastic rotor models, between the frequency of two adjacent lines.
If you observe in your experiment that the peak efficiency of your motor occurs at ω=5.2 and T=0.054 and you need to lift a mass of 218 g, what is the pulley radius (m) that should be used to achieve peak efficiency?
why the overdamped curve lies above the critically damped one and approaches zero at slower rate?
What is the purpose of the Tip Mass in the model of the Magnetostrictive vibration energy harvester?
Given the following experimental data collected, what is the approximate torque of this motor at peak efficiency?
Find the horsepower rating of a motor running at 1,500 rpm and developing a torque of 105 lb–ft. (a). 22 (b). 28 (c). 30 (d). 36
Q.2 A reciprocating air compressor has a 5 ft-diameter flywheel 14 in wide, and it operates at 170 rev/min. An eight-pole squirrel-cage induction motor has nameplate data of 50 bhp at 875 rev/min. (CLO2) (a) Design a V-belt drive. (b) It is suggested that chain drive may be used for the power transmission, design a chain drive.
A motor running 1800rpm transmits 10KW of power through a 25mm diameter shaft 1.2m long. What is the angle of twist in the shaft? G=8.3x10^10 Pa. A)1.14 degree B)1.59 degree C)1.34 degree D)1.04 degree
A 7460 W split-phase motor running at 1750 rpm is used to drive a rotary pump. The pump should run continuously at approximately 1175 rpm. The center distance should not exceed 1118 mm. Space limits the diameter of the driven pulley to 292 mm. Determine: a. the pulley diameters, b. the belt size, and c. the number of belt required.