A 50-kN force is subjected to a lap joint fastened by three 20-mm diameter rivets.(a) the shearing stress in each rivet.(b) the bearing stress in each plate.(c) the maximum average tensile stress in each plate. Assume that the axial load P is distributed equally amongthe three rivets. equally among the three rivets. A 50-kN force is subjected to a lap joint fastened by three 20-mm diameter rivets.(a) the shearing stress in each rivet.(b) the bearing stress in each plate.(c) the maximum average tensile stress in each plate. Assume that the axial load P is distributed equally amongthe three rivels. equally among the three rivels.To o oP20 mm-25 mmP.

A 50-kN force is subjected to a lap joint fastened by three 20-mm diameter rivets. (a) the shearing stress in cach rivet. (b) the bearing stress in each plate. (c) the maximum average tensile stress in each plate. Assume that the axial load P is distributed equally among the three rivels, equally among the three rivels. To o o o 20 mm to 25 mm P.

A 50-kN force is subjected to a lap joint fastened by three 20-mm diameter rivets. (a) the shearing stress in cach rivet. (b) the bearing stress in each plate. (c) the maximum average tensile stress in each plate. Assume that the axial load P is distributed equally among the three rivels, equally among the three rivels. To o o o 20 mm to 25 mm P.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.
A 14 mm diameter rivet joins the plates that are each 1.10 m wide. The allowable stresses are 120 000 KPa for bearing in the plate material and 60 000 KPa for shearing rivet. Determine the minimum thickness of each plate and the largest average tensile stress in the plates
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t = 0.3125 in. The average shear stress in the pin cannot exceed 45 ksi, and the bearing stress in the pulley support bracket cannot exceed 65 ksi. Determine the maximum value of Pmax that can be supported by the assembly.
Two solid cylindrical rods AB and BC are welded together at Band loaded as shown. Determine the magnitude of the force Pfor which the tensile stresses in rods AB and BC are equal. Take W= 12 kips. 30 in. -1.25 in. B W 25 in. 0.75 in. The magnitude of the force Pis kips.
For a steel rod with a circular cross section with a diameter of D = 20 mm, the following is required: 1. Draw a diagram of the longitudinal force 2. Draw a diagram of normal stresses 3. Determine the total elongation of the rod if Е = 2∙10^5 MPa When calculating, take: а = 2 m, b =1.2 m, F=10 кN - The point of application of force! The work must be done on one sheet of A4 paper, which must show: - Using the method of sections to determine the longitudinal forces in the rod. - Draw a diagram of longitudinal forces N - Determination of normal stresses based on the constructed plot of longitudinal forces. - Draw diagram a normal stresses - Determination of the full extension of the rod
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.002L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of 2L, determine the elongation of the block.
The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear stress in the bolts must be limited to 249 MPa, determine the minimum bolt diameter that may be used in the connection.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.