Answered: A body is subjected to a direct tensile…

A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.27P: -27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile...

See similar textbooks

Related questions

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: The torque of 12kN m is applied to the 6-meter steel shaft's free end. The shaft must rotate at a…

Q: A cylindrical water tank a thickness of 0.6 inhas an internal pressure of 580 psi. a.If the tank…

Q: Determine the principal stresses and the absolute maximum shear stress. 2.5 ksi 4 ksi 5 ksi

Q: At a point in a stressed body, the cartesian components of stress are Oxx = 60 MPa, Guy = -40 MPa,…

A: Given Data σxx=60 Mpa σyy=-40 Mpa σzz=20 Mpa τxy=-40 MPa τyz=20 MPa τxz=30 MPa Stress tensor,…

Q: Determine the magnitude of the maximum shear stress on the stress element for which σx=-87 MPa,…

Q: The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.…

Q: A thin-walled cylinder has an internal diameter of 1200 mm and has walls 1.2 mm thick. It is…

A: For solution refer below images.

Q: 2. A hollow shaft of 30-mm inner diameter and 60-mm outer diameter is acted on by an axial tensile…

Q: A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in.…

Q: The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and…

A: Mohr's Circle

Q: A solid shaft of diameter 30 mm is fixed at one end. It is subjected to a tensile force of 10 kN and…

A: Data given - D = 30 mm = 0.03 m Tensile force Ft = 100 kN Torque T = 60 Nm

Q: if the maximum and minimum principal stresses at a point are (27 Mpa) and (5 Mpa) respectively. The…

A: Maximum shear stress is equal to difference of maximum principal stress and minimum principal stress…

Q: In one revolution of a shaft the stresses which vary from a value of tensile stress to the same…

A: cyclic stress occurred when load carrying element is subjected to some value of tensile stress to…

Q: The cross-sectional area of bar ABCD is 600 mm?. Determine the maximum normal stress in the bar.…

A: Given data: Force acting at B = 25kN Force acting at C = -20kN Force acting at D = 30kN Cross…

Q: 30 mm and 40 mm, respectively. Determine the principal stresses and

Q: Determine the principal stresses and the absolute maximum shear stress.

A: Given: The normal stress on the vertical plane is σX=20 ksi. The normal stress on the horizontal…

Q: A point is subjected to tensile stresses of 200 MPa and 150 MPa on two mutually perpendicular planes…

A: Stress is defined as the resistance force acting per unit cross-section area of the body. It is also…

Q: At a point in plane stress the principal stresses were found to be 22 MPa(T) and 14 MPa (C). The…

A: The given data are: σ1=22 MPaσ2=14 MPa Here, σ1 denotes the maximum principal stress and σ2 denotes…

Q: A motor boat engine shaft is coupled to the propeller shaft of diameter 30mm. If the allowable shear…

A: Given, Allowable shear stress, τ=43 MPa=43 N/mm2 The diameter of the shaft, d=30 mm

Q: A cylindrical steel pressure vessel has an inner radius of 24 inches and wall thickness of 0.25…

Q: (Q2: if a point is subjected to the state of stress shown in figure determined the principles stress…

Q: rect stresses of 160N/mm tensile and 120 N/mm compressive exist on two perpendicular planes at a…

A: Given, direct tensile stress, σt=160N/mm2 Compressive stress, σc=120N/mm2 The greatest principal…

Q: determine (a) the principal stresses and their principal planes, (b) the maximum shear stress and…

Q: For the state of plane stress shown below, determine the principal stresses, the maximum in plane…

Q: 1.4 kNm C H KI 10 kN 240

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an…

Q: For the state of plane stress shown below, determine the principal stresses, the maximum in- plane…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: 8.5 The material of Problem 8.4 is subjected to an additional shearing stress of 10 MN/m. Determine…

A: 8.6 Given: The direct stress in direction 1, σ = 45 MN/m^2 The direct stress in direction 2, σ = 75…

Q: the normal stress using Mohr's circle

A: Given: X = 7 ksi and Y = 35 ksi To determine: The normal stress using Mohr's circle

Q: At a point in a material under stress there is a compressive stress of 200MN/m2 and a shear stress…

Q: At a point on the flat surface of a member, load-stress relations give the following stress…

A: GIVEN: σxx=100 MPaσyy=0σzz=100 MPa τxy=20 MPaτxz=0τyz=20 MPa To find the principle stress σ2 and its…

Q: A point is subjected to tensile stresses of 200 MPa and 150 MPa on two mutually perpendicular planes…

A: Principle stress and principle planes are the planes that may be subjected to the only normal stress…

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: It is known that the seam, which is rotated 45∘ from the vertical, as shown in Fig. E3-c, will fail…

Q: A line shaft rotating at 200 rpm is to transmit 20 kW. The allowable shear stress fo the material of…

Q: 2.6. The principal stresses at a given point are ơ1 =10 ksi, o2 =5 ksi. Sketch Mohr's circle for…

A: givenσ1=10ksiσ2=5ksi

Q: 1. A material is subjected to equal bi-axial tensile stresses of 60 MPa along the x- and y-axes.…

Q: At a certain section in a material under stress, direct stresses of 45 MN/m2 tensile and 75 MN/m2…

A: Given Data : Direct Stresses are

Q: If P is equal to 125 kN Determine the normal stresses of members DH & HG in kPa. The diameter of…

A: Given data, P= 125 KN Diameter d= 120 mm = 0.12 m Cross section area = A= 0.25*π*d² = 0.01131 m²

Q: Current Attempt in Progress 180 MPa, o, = 50 MPa. At a point in a machine component that is…

Q: At a point in a stressed body the state of stress on two planes 45° apart is as shown below.…

A: Given:σx=8 MPaτxy=3 MPaθ=45o

Question

A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
1 A rectangular steel plate with thickness t = 5/8 in. is subjected to uniform normal stresses a and ., as shown in the figure. Strain gages A and B. oriented in the x and v directions. respectively, arc attached to the plate. The gage readings give normal strains = 0.00065 (elongation) and £. = 0.00040 (elongation). Knowing that E = 30 X 106 psi and v = 0.3, determine the stresses c7 and a, and the change .11 in the thickness of the plate.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
At a point in a material under stress there is a compressive stress of 200MN/m2 and a shear stress of 300MN/m2 acting on the same plane. Determine the principal stresses and directions of the planes on which they act
A point is subjected to tensile stresses of 200 MPa and 150 MPa on two mutually perpendicular planes and an anticlockwise shear stress of 30 MPa. Determine by any method the values of normal and shear stresses on a plane inclined at 60° with the minor tensile stress.
A torque of 1.4KNm and two forces of 10kN and 12kN are applied to the top of a 65mm diameter solid steel post. Determine the principal stresses and the maximum shear stress at point H and point K.
Show that the angle between the plane of the major principal stress and the plane of the maximum shear stress is 45° for any state of stress.
At a certain section in a material under stress, direct stresses of 45 MN/m2 tensile and 75 MN/m2 tensile act on perpendicular planes together with a shear stress τ acting on these planes. If the maximum stress in the material is limited to 150 MN/m2 tensile, determine the value of τ.
Direct stresses of 160N/mm tensile and 120 N/mm compressive exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stresses on the planes. The greatest principal stress at the point due to these is 200 N/mm?. a) What must be the magnitude of the shearing stresses on the two planes? b) What will be the maximum shearing stress at the point?