A 50-mm-diameter aluminum compound shaft is loaded by torques at the gears as shown in the figure. Determine the angle of rotation of gear D relative to gear A. Use Galuminum = 28 GPa. 600 N-m 900 N-m 1100 N-m 800 N-m 3 m

A 50-mm-diameter aluminum compound shaft is loaded by torques at the gears as shown in the figure. Determine the angle of rotation of gear D relative to gear A. Use Galuminum = 28 GPa. 600 N-m 900 N-m 1100 N-m 800 N-m 3 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Related questions

Q: Find the velocity, acceleration, and speed of a particle with the given position function. r(t) = 2i...

A: As given in question, Position function = r(t) = t2 i + 8t j + 3 ln(t) k From position function, v...

Q: The correct stress state for representing the circumference of the pressure vessel is which of the f...

A: Find the state of stress at circumference of pressure vessel

Q: 8 KN 4 kN 15 kN m 0.5 m

A: Given

Q: Five kilo of water vapour are contained at 178 kPa and 85 percent quality is a suitable enclosure. C...

Q: Hot oil is pumped through a heat exchanger (see figure below) at a flow rate of 0.5 L/s. An inlet ma...

Q: In a pumping system handling water, the level in the suction tank is 3.2m below the pump shaft cente...

A: NOTE:- As per our company guidelines we are supposed to answer only one question. Kindly repost othe...

Q: The estimated times and immediate predecessors for the activities in a project at Howard Umrah's rot...

Q: Please provide equations that you are using so I can follow along and learn how to do this and inclu...

Q: For part d, we introduce a wall at cross-section A. Determine the absolute maximum shear stress on t...

Q: what is the effect of friction factor on the pumping power?

Q: A shaft has three segments. AB and CD are made from C86100 bronze and BC is made from 2014-T6 alumin...

Q: An orificemeter with orifice diameter 12 cm is inserted in a pipe of 20 cm diameter. The pressure di...

Q: Normal state New state <Force Applied → Normal state Free Position Operating Position Free Position

A: The above picture given shows the the positions of limit switches. Limit switches : Definition :A l...

Q: Solve the following problem :a.What is the weight of a 1-kg mass at an altitude where the local acce...

A: Given data, m= 1 kg g= 9.75 m/s² Note: for part b, complete data is not given.

Q: Knowing that tanks exposed into the atmosphere have pressure of atm. What is the design pressure? a...

A: The tank design on basis of pressure can be done by three ways: Atmospheric pressure design Full va...

Q: Why do we need to calibrate temperature measuring devices?

A: Temperature measuring devices can range from thermometers to optical sensors. Generally, these measu...

Q: A 4 stroke gas engine develops 4.5kw at 180rpm at full load.Assuming the following data, calculate t...

Q: device's outer cylinder diameter is 5" and its distance from outer cylinder to the inner cylinder is...

Q: Determine transfer function of Figure 1.

A: NEED TO DETERMINE THE TRANSFER FUNCTION.

Q: Composite Material There is a new wearable device that is made from a complex somposite solid materi...

A: Energy harvesting has sparked a lot of attention from both academia and industry because it has the ...

Q: A piece of metal weighs 350 N in air and when it is submerged completely in water it weighs 240 N a...

Q: Steam at 2000 psia and 1000°F enters the high-pressure turbine of a reheat cycle and is expanded adi...

Q: nd its distance from outer cylinder to the inner cylinder is 0.0364". The said outer cylinder of the...

Q: A) Why do we need to follow 0.5 inch of untwisting of the cables in the RJ-45? B) What is the purpos...

A: Rj-45 - is a connector used for Ethernet networking . Rj stands for registered jack and 45 refers t...

Q: A small aircraft A is about to land with an airspeed of 75 mi/hr. If the aircraft is encountering a ...

Q: If an aircraft has a 338 m/s velocity, determine its mach number if air is at 359K. Round your answe...

A: M = mach number V= velocity of object C= speed of sound air at 359k C= 379.7 m/s Mach no= it can...

Q: 2 litre of petrol weighs 14n. calculate the specific weight, density, specific volume and specific g...

Q: lasticity, el

A: solution of above question is below

Q: 2. The 1-m diameter cylinder in the figure is 8 meters long (dimension perpendicular to the paper) a...

Q: A circular bar of "500" mm length is supported freely at its two ends. It is acted upon by a central...

Q: connected to a power transmission shalt of diameter d by means of a rectangular sunk key of width w ...

Q: A 30 mm diameter shaft transmits 10 kW at 600 rpm. It was found that a stress raiser exist whose str...

A: The given values are - P= 10 kW, d= 30mm, N = 600rpm, τsy=150 MPa Let T be the twisting moment.

Q: A circular bar of L 570mm length is supported freely at its two ends. It is acted upon by a central ...

Q: Solve for the ratio of the initial to final speed of sound if an air expands isentropically from 164...

Q: A wheel tractor has a 200HP engine.if it is operating at an altitute of 1000m above sea level, at an...

Q: The rectangular plate is deformed into the shape shown by the dashed lines. If ?? has a normal strai...

Q: enlarged by blowing air into it. If the surface tension of the soap solution is 0.0047 lbf/ft, deter...

Q: .3 The reciprocating masses of the first three cylinders of a four cylinder engine are 4.1, 6.2 and ...

A: give masses of first three reciprocating parts m1 = 4.1 tonnes , m2 = 6.2 tonnes , m3 = 7.4 tonnes ,...

Q: resultant of the three forces is a horizontal force. Determine (a)the magnitude of p (b) the magn...

A: To determine the value of P, resultant and the angle of resultant.

Q: The following table lists molecular weight data for a polypropylene material. Compute the weight-ave...

Q: 12 kN E 12 kN F 3 m 12 kN G A C D 2 m 2 m 2 m to

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN GIVEN MEMBER

Q: Locate the amount and position of the resultant of the load acting about A.

Q: Omar, a Professional Engineer (P. Eng.) with many years of experience and a valid Certificate of Aut...

A: 1. The issue here is that the design is free of flaws or defects, but the correct installation is no...

Q: A sub-marine with its axis 15 m below water surface fitted with pitot tube moves horizontally in sea...

A: We must determine the speed of a sub-marine with an axis 15 m below the water surface and a pitot tu...

Q: Two horizontal plates are spaced 3 in. apart. The space between the plates is filled with mercury at...

A: (a) Write the given data. y=3 invupper=3 ft/s

Q: A steel bar carries a bucket of weight W hanging at its lower end. Given: Bar diameter= 12 mm Length...

A: Answer : (a) The weight of bucket as per allowable stress is steel is 14.70265 kN. (b) The weight o...

Q: A 60 mm diameter Orifice is discharging water under a head of 9 meters. Calculate the actual dischar...

A: Given Data: d0=60 mm=0.06 mh=9 m, Cd=0.625Cv or Cc=0.98a0=π4d12=π4×0.062=2.827×10-3 m2

Q: The following instruments are considered gyroscopic. * Tachometer VSI Altimeter Fuel qua...

Q: P3.114 Water flows through a circular nozzle, exits into the air as a jet, and strikes a plate, as i...

Q: 4. A differential band brake is shown in the figure. The diameter of the drum is 800 mm. The coeffic...

Concept explainers

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.

Question

b, Use 2 decimal place for the final answers.

Problem 2.
A 50-mm-diameter aluminum compound shaft is loaded by torques at the gears as shown in the figure.
Determine the angle of rotation of gear D relative to gear A. Use Galuminum = 28 GPa.
600 N-m
900 N-m
1100 N-m
800 N-m
2 m
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
The two solid steel shafts shown in the figure are connected by gears. Determine the angle of twist of end A of shaft AB when the torque T = 25 N - m is applied. The DC axis is fixed at D. Each axis has a diameter of 20 mm. G = 70GPa.
In the gear system shown in the figure, the motor applies a torque of 231 N-m to the gear at A. A torque of TC = 440 N-m is removed from the shaft at gear C, and the remaining torque is removed at gear D. Segments (1) and (2) are solid 38-mm-diameter steel (G = 80 GPa) shafts, and the bearings shown allow free rotation of the shaft. Assume DA = 110 mm, DB = 370 mm, L1 = 1.7 m, and L2 = 1.1 m. Calculate the rotation angle of gear D relative to gear B. Express your answer in radian rounded to the nearest thousandths.
The compound shaft shown in the figure consists of a d1 = 37 mm solid bronze [Gbronze = 40 GPa] shaft (1) and a 25 mm solid steel [Gsteel = 85 GPa] shaft (2). The compound shaft is subjected to torques of 780 N.m and 300 N.m at B and C, respectively. Let L1 = 800 mm and L2 = 1470 mm. Determine the internal torque in shaft (2)?in N.m Determine the maximum shear stress in shaft (2)? In MPa Determine the angle of twist in shaft (1). Determine the angle of twist in shaft (2). Determine the angle of twist at C with respect to the support.
An aluminum shaft with a constant diameter of 50 mm is loaded by torques applied to gears attached to it as shown in the figure. Using G = 28 GPa, determine the relative angle of twist of gear D relative to gear A. Note: SHOW FBD AND DETAILED SOLUTION
A motor supplies a torque of 5.5KNm to the constant diameter steel (G= 80GPa) line shaft shown in the figure. Three machines are driven by the gears B, C, and D on the shaft, and they required torques of 3.0KNm, 1.5KNm, and 1.0KNm, respectively. Determine: a. The minimum diameter required if the maximum shearing stress in the shaft is limited to 100MPa.b. The rotation of gear D with respect to the coupling at A if the coupling and gears are spaced at 2m intervals and the shaft diameter is 75mm.