Answered: A 500 kg block falls a distance of 5 m…

A 500 kg block falls a distance of 5 m from level A and hits the untensioned spring on level B The spring is compressed to level C, a distance of 3 m as indicated. Determine spring stiffnes

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.79P: The coefficient of rolling resistance between the 30-kg lawn roller and the ground is r=0.1. (a)...

See similar textbooks

Related questions

Q: The 50-lb block rests on the rough surface for which the coefficient of kinetic friction is µ̟ =…

A: Given data-μk=0.2 mg=50lbF=100lbδ=5ft

Q: Q1/ The 30-lb collar A is released from rest in the position shown and slides with negligible…

Q: *14-16. A small box of mass m is given a speed of » = Vigr at the top of the smooth half cylinder.…

A: Draw the free-body diagram of the block.

Q: Block A has a weight of 150N and rest on surface for which u, = 0.4. Determine the maximum weight of…

Q: Q1/ The 30-lb collar A is released from rest in the position shown and slides with negligible…

Q: The conveyor belt delivers each 20-kg crate to the ramp at A such that the crate's speed is 2.5 m/s,…

A: Given Mass, m = 20 kg Velocity of crate, VA = 2.5 m/s Coefficient of friction…

Q: The 250-lb concrete block A is released from rest in the position shown and pulls the 400-lb log up…

A: Draw the given figure,From the figure, VA=2VC aA=2ac Draw the free body…

Q: The block of weight 8 Ib is released from rest at. and slides down the smooth circular surface AB.…

Q: A jackhammer exerts the impulse shown below on the 1.5 kg bit to drive it towards the ground. If the…

A: Here, area under F-t diagram gives impulse. Area of diagram = Area of trapezium. Impulse =12×Sum of…

Q: Crate B has a mass m and is released from rest when it is on top of cart 4, which has a mass 3m.…

Q: A car having a mass of 2Mg strikes a smooth rigid sign post with initial speed of 30km/h. To stop…

Q: The 6-kg spiked pendulum is released in position 1. When the pendulum reaches position 2, the spike…

A: Consider the diagram shown below for the given system.

Q: The 50 kg block is released from rest at A. Determine the compression of each of the springs after…

Q: The system of two blocks, cable, and fixed pulley is initially at rest. Determine the horizontal…

A: Free Body Diagram

Q: The spring attached to the 1.8-kg block is undeformed when the system is in the position shown. The…

A: Write the formula for the potential energy of the spring when it touches the ground. E=12kx2 Here, x…

Q: The block of weight W is released from rest at A and slides down the smooth circular surface AB. It…

A: Given details: W=25 Na=0.9 mb=0.6 mk=660 N/mμk=0.2θ=90°

Q: Determine the speed v which the 685-kg four-man bobsled must have in order to negotiate the turn…

Q: 14-25. The 5-lb cylinder is falling from A with a speed vA = 10 ft/s onto the platform. Determine…

Q: The man pushes the 20 lbm crate with a force of F = 150 lbf and with an angle of 45 deg from…

A: find the power supplied by the man.

Q: The 1.2-kg small collar is released from rest in position A and slides up the smooth fixed rod…

A: The net force able to push the spring by 0.5 m. Spring constant, K = 150 N/m

Q: Q6: The 7-kg collar A slides with negligible friction on the fixed vertical shaft. When the collar…

A: Given datam=7 kgf=200 Nx=75 mmTo find 'K'

Q: 14-30. The 30-lb box A is released from rest and slides down along the smooth ramp and onto the…

A: Given Data: The weight of box is W = 30 lb. The coefficient of friction is μk = 0.6. The height at…

Q: Q1/ The collar A has a mass of 8 kg slides with negligible friction on the fixed vertical shaft.…

A: Friction is the force exerted by two surfaces moving (or attempting to slide) over one another.…

Q: 2. The 50-kg crate starts from rest and pull by a Motor and as shown in Figure 2. If the…

A: Givenm=50kgμk=0.2s=10mt=15s

Q: The box having a weight of 40 N is moving to the right along a rough surface. When the package is at…

Q: The 950-kg motorized unit A is designed to raise and lower the 450-kg bucket B of concrete.…

Q: determine its velocity when it hits the floor.

A: The kinetic energy of the spring is equal to its elastic potential energy, i.e. 1/2mv^2 = 1/2kx^2…

Q: Q2: The 0.5-kg cylinder A is released from rest from the position shown and drops the distance h, -…

A: The stiffness of a spring is defined as the ratio of the external effort applied to that of the…

Q: Q6: The 7-kg collar A slides with negligible friction on the fixed vertical shaft. When the collar…

Q: 3/326 The spring of stiffness k is compressed and sud- denly released, sending the particle of mass…

Q: A C | 3.5 ft B d

A: Apply equation of conservation of…

Q: Determine the speed v which the 685-kg four-man bobsled must have in order to negotiate the turn…

A: Given: m=685 Kg radius r=59 m

Q: Ball A weighs 1.962 N. If it is dropped on the inclined rigid surface (0-30), determine the rebound…

A: given data; weight(w)=1.962Nthen mass of ball(m)=wg=1.9629.81=0.2kginitial…

Q: The 5.6-lb cylinder is falling from A with a speed va = 10 ft/s onto the platform. The spring has an…

Q: The 1.2-kg. slider of the system of Prob. 3/149 is re- leased from rest in position A and slides…

Q: A 60-kg suitcase slides from rest 5 m down the smooth ramp. Determine the distance R where it strike…

Q: Each of the two elastic rubber bands of the slingshot has an unstretched length of 200 mm. If they…

Q: The cart carrying the small 2-kg package A is moving up the incline with constant acceleration N. If…

Q: he block has a mass of 0.6 kg and moves within the smooth vertical lot. The block starts from rest…

Q: momentarily at rest. Determine his speed and the tension in each of the two supporting cords of the…

A: Given that weight of the boy is 60 lb. It is required to determine the tension in each cord and…

Q: E A bead with a mass of 0.25 kg is released from rest at A and slides down and around the fixed…

A: Given data as per the question Mass =0.25 kg Calculations considering point A as the datum apply…

Q: The 0.7 lblb ball is shot from the spring device shown Determine the smallest stiffness k which is…

Q: The 10-lb collar starts from rest at A and is lifted by applying a constant vertical force of F = 25…

A: Given: The mass of collar, m = 10 lb The vertical force, F = 25 lb The angle, θ = 60°

Q: The block of weight W is released from rest at A and slides down the smooth circular surface AB. It…

A: Given data: The weight of the block is W=25 N The value of a is a=0.9 m The value of b is b=0.6 m…

Q: The 7.6-kg cylinder is released from rest in the position shown and falls on the spring, which has…

A: The additional deflection of the spring is 45.33 mm.

Q: Determine the speed v which the 655-kg four-man bobsled must have in order to negotiate the turn…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

A 500 kg block falls a distance of 5 m from level A and hits the untensioned spring on level B.
The spring is compressed to level C, a distance of 3 m as indicated. Determine spring stiffness.
A
X =Sm
B.
h= 3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 4-kg box slides on the smooth surface and has a velocity of 15 m/s. If it strikes the smooth plate, which has a weight of 2 kg and is held in position by an unstretched spring of stiffness k = 600 N/m, determine the maximum compression imparted to the spring. Take e = 0.7 between the box and the plate.
A car having a mass of 2Mg strikes a smooth rigid sign post with initial speed of 30km/h. To stop the car, the front end horizontally deforms 0.2 m. If the car is free to roll during the collision, determine the average horizontal force causing the deformation
The 1.9-kg slider is released from rest in position A and slides without friction along the vertical-plane guide. Determine the normal force exerted by the guide on the slider (a) just before it passes point C, (b) just after it passes point C, and (c) just before it passes point E. The normal forces are positive if they point up and/or to the left, negative if they point down and/or to the right.
An automobile of mass 1000 kg is driven down a 5o incline at a speed of 72 km/h when the brakes are applied causing a constant total breaking force of 5000 N. Determine the distance traveled by the automobile as it comes to a stop. Also Draw Free body diagram
URGENT Collar A slides over the smooth vertical bar shown in the figure. The masses Wa = 10lbs and WB = 5lbs. When h = 0.12192m, the spring is unextended. When the system is in equilibrium, h = 0m. Determine the constant k of the spring. Note: The normal of the collar is 100 times its mass (that of the collar), remember that g = 32.16 ft/s2.
*8–60. Each block has a weight of 400 lb. Determine how far the force P can compress the spring until block B slips on block A. What is P for this to occur?
A 50 kg block is dropped from a height of 2 m onto the the 20 kg pan of a spring scale. Assuming the impact to be perfectly plastic, determine the maximum deflection of the pan. The constant of the spring is k = 20 kN/m.
The 0.31-kg mass slides on a frictionless wire that lies in the vertical plane. The spring attached to the mass has a free length of 80 mm and stiffness of 0.13 N/mm. Calculate the smallest value of the distance b so that the mass will reach the end of the wire at B after being released from rest at A.
The 81-kg crate is subjected to the forces shown. If it is originally at rest, determine the distance it slides in order to attain a speed of v = 8 m/s. The coefficient of kinetic friction between the crate and the surface is uk = 0.27. Forces with respect to 45° and 30° are 611 N and 398 N, respectively
The crate, which has a mass of 180 kg If it is originally at rest, determine the distance it slides in order to attain a speed of 9 m/s. The coefficient of kinetic friction between the crate and the surface is μk = 0.2. Please answer using 3 sig figs.
Find the minimum force P for impending motion of the refrigerator shown, and determine whether it will slip or tip, given:W = 180 lbs, L1 = 4.5 ft, L2 = 3.7 ft, L3 = 2.3 ft, L4 = 1.5 ft, μS = 0.5
The elastic cord has an unstretched length l0 = 1.5 ft and a stiffness k = 12 lb/ft. It is attached to a fixed point at A and a block at B, which has a weight of W = 2.2 lb. The block is released from the rest from the position shown. After leaving the guide, it is launched onto the smooth horizontal plane. (Figure 1) (A) Determine its speed when it reaches point C after it slides along the smooth guide. Express your answer to three significant figures and include the appropriate units. (B) Will the angular momentum of the block about point A be conserved after it passes point C? yes or no. (C) Calculate the magnitude of the angular momentum of the block about point A, at any instant after it passes point C. Express your answer using three significant figures. (D) Determine if the cord becomes unstretched. The cord will not become unstretched The cord will become unstretched