he 0.31-kg mass slides on a frictionless wire that lies in the vertical plane. The spring attached to the mass has a free length of 80 mm and stiffness of 0.13 N/mm. Calculate the smallest value of the distance b so that the mass will reach the end of the wire at B after being released from rest at A.

Q: Suppose you purchase a 4 x 8 piece of plywood from Home Depot. You don't have a pickup truck (nor…

A: Given: ρ= 0.002369 slugs/ft3μ= 3.7372 × 10-7 slugs/ft.s

Q: Q4/ Draw the mohr's stress circle or the element of the beam as shown in Fig. 4, and determine the…

A: Given: The stress along x-direction, σx = 100 MPa The stress along y-direction, σy = 60 MPa The…

Q: Given: The truss loaded as shown, 110% 110K e a b Fot d 8' 8' 8' Required: Solve for external…

A:

Q: B-Find the internal energy of perfect gas at 1 MPa and 0.2 m³kg. The molecular weight is 30 and the…

A: Introduction: The random, disorganized motion of molecules is designated as a system's internal…

Q: A mass of 5 kg of saturated water vapor at 300 kPa is heated at constant pressure until the…

A:

Q: Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable…

A:

Q: 13. The maximum permissible recoil distance of a gun is specified as 0.5 m. If the initial recoil…

A:

Q: Approximate the theoretical power in wind moving at a speed of 6 m/s with an air temperature of 40°F…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: Non-destructive testing of large molded pieces may be performed using radiation. Discuss what…

A: Given question: Discuss what constructive elements a non-destructive testing system should contain,…

Q: A gas having a volume of 12 gal has a pressure of 0.24 MPa at 24°C. If the gas constant R is equal…

A: The Ideal Gas Equation is given by:- PV=mRT where, m=mass of the gas(kg)R=Characteristic Gas…

Q: Calculate the heat transfer rate for the following composite wall configurations: (A)Consider a…

A: DISCLAIMER FOR MULTIPLE QUESTIONS FROM BARTLEBY: Since you have asked multiple question, we will…

Q: Convert a -6 kPa (negative 6 kiloPascal) pressure to an absolute pressure in kPa

A: Calculated a -6 kPa (negative 6 kilo Pascal) pressure to an absolute pressure in kPa.

Q: mm and 7.6 An orthogonal machining operation is performed on a mild steel part 5 mm wide. The tool…

A: Introduction: The cutting velocity in orthogonal cutting is perpendicular to the breadth of the…

Q: a) A successful Fluid Dynamics lecturer uses a board above their automobile to promote their course…

A:

Q: Hooke's Law defines which one of the following regions of the stress strain relationship for…

A: Solution.jpg

Q: Two centrifugal pumps are connected in parallel in a given pumping system. Plot total head Ah…

A: Given:

Q: Question 14 The total amount that the feature on the actual part is allowed to vary from the…

A: Allowance: It is the difference between the basic sizes (difference between the hole diameter and…

Q: Fifteen gallons of hydraulic oil weigh 108.7 lb. What is the specific weight γ in units of lb/ft3?…

A: Given that, Volume of hydraulic oil = V=15 gallons=15×0.1337 ft3=2 ft3 Weight of oil = W=108.7 lb

Q: Compute for A • B: A = 7i - 2j B = 7i+ 3j - 4k Select the correct response: О о O 1 unit O 49 units…

A:

Q: Figure 1 shows a compressor running on refrigerant-134a with a constant mass flow rate of 6 kg/s.…

A:

Q: Hypothetical metal has an FCC crystal structure. If its density is 22.4 g/cm3, and atomic weight is…

A:

Q: Q2 a) Consider the wing of an aircraft as a flat plate of 25 m length in the flow direction (Figure…

A:

Q: Question 10 The primary unit of measurement for engineering drawings is? Select one: O A. Metre B.…

A: Primary unit: The stocking unit that is used to measure the dimensions of any object in an…

Q: Using the lead-un phase diagram in a nominal composition of 30% Sn and 70% Pb at 250°C (482°F).…

A: At T = 250 deg. Celcius composition of Sn = 30% Composition of Pb = 70%

Q: (b) A hydrogen gas cylinder is situated in the cylinder cage. The cylinder wall is constructed from…

A:

Q: An airplane is traveling at 275 m/s in still air at 0 °C. If the Cp value is 1.005 kj/kgk and k=1.4,…

A: Gven: v = 275 m/s Cp = 1.005 kJ/kgK  k = 1.4 T = 0 + 273 = 273 K

Q: . When water freezes, it expands by about 9.00%. What pressure increase would occur inside your…

A: Given: expansion of 9% k = 2 * 109 N/m2

Q: 1- Conservation of mass 2-Gravitational Energy. 3-Internal Energy....

A: Given Conservation of mass Gravitational energy Internal energy To find Definition

Q: Assume a simple spring-mass system has the following system parameters and initial conditions: m =…

A: Given data: m =  100 kg k = 100 N/m x0 = 1 m  v0 = 0 m/s

Q: لنقطة of Warm working The advantages over cold working are: 1) forces and power are higher,2) more…

A:

Q: At 1 atm and 20 oC, air flows in a 7 cm diameter tube. What should be the maximum air velocity to…

A:

Q: 5. The theoretical maximum power efficiency of any design of wind turbine is 0.95. [True/False] 6.…

A: 5. Wind turbine is used to convert the kinetic energy of the wind to the electrical energy. It is…

Q: 19- Considering the incompressible, frictionless flow of water in a vertical pipe, the pressure is…

A:

Q: A 2600-lb car is moving at a speed of 66 mph when the brakes are fully applied, causing all four…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A:

Q: 3. A simple pendulum has a mass of 0.250 kg and a length of 1.00 m. It is displaced through an angle…

A:

Q: A hollow steel has an outside diameter of 5in. and it's inside diameter is 4in. What is the…

A: Given data : Outside diameter (dO)=5 in Inside diameter (di)=4 in   To find : Thickness of steel

Q: 4. Oil with viscosity 2 x 10-2 Ns/m2 and density 850 kg/m3 is pumped along a straight horizontal…

A:

Q: An open vessel in the form of a frustum of a cone with a radius of 1.2m (bigger base), the smaller…

A: Given: The radius of frustum at base, R = 1.2 m The radius of frustum at top, r = 1 m The slope of…

Q: Question 1: The 0.2-slug ball falls from rest to the ground from a 50-ft height. During the fall it…

A:

Q: Find the offset angle for an axial pump that delivers 50 gpm at 1750 rpm. The volumetric efficiency…

A: Given     Speed, N = 1750 rpm    Efficinecy = 95% Diameter, d = 0.75 in Find  Offeset angle

Q: (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b)…

A: Given: Grid square size is 11 ksi. Mohr's circle can be denoted here as,

Q: 14. A spring-mass system is found to vibrate with a frequency of 120 cycles per minute in air and…

A:

Q: An axial pump that delivers 15 gpm, has a volumetric efficiency is 93%. Find its theoretical flow…

A: Given: actual flow rate = 15 gpm volumetric efficiency = 93%

Q: PROBLEM 12 A 20 mm shaft is loaded as shown below (S, = 290 MPa). Determine the location of maximum…

A: Introduction: In some applications, the shaft is subjected to both bending moment and torque.…

Q: Q1: The 1.5-kg ball is given an initial velocity v = 2.5 in the vertical plane at position A, where…

A:

Q: A vehicle with a Diesel Engine operates with the ideal Diesel cycle Air entering at 101.3 kPa and…

A: GivenP1=101.3 KPT1=26.85 C =299.85 Krk=20rc=2

Q: QUESTION 5 Given the Volumetric Analysis of a Natural Gas: CH4 = 67.3% Nitrogen = 9.6% 0₂ = 2.7%…

A:

Q: An alloy system consists of two metals A&B which are soluble in each other in all proportions in the…

A: The phase diagram and the corresponding point for the given wt% of A and B is shown below.

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.