A 50KVA, 500/1000V Y-Y Transformer has per phase R=40, X=50, R_= open circuit, X=120k0 refer to high eq m eq voltage side. The equivalent circuit using per unit system equal:
Q: Question 1: Determine the i, current for the below transformer. Given parameters: N1=1250 Turns,…
A:
Q: A12 Efficiency of DC machine is high as compared to the transformer. (TRUE/FALSE)
A: In all electrical machines transformer will have higher efficiency. Because there are no rotational…
Q: A 40KVA, single-phase transformer is tested on both open-circuit and short-circuit conditions,…
A: The given parameters are as follows:-
Q: Q2: A 4000/400 V, 10 kVA transformer has the following constants: Primary and secondary winding…
A: Given values are -
Q: (a) A 220 / 40OV, 11KVA, 50HZ single phase transformer has at full load, a copper load of 145W. If…
A:
Q: A 150 kVA, 2400/240V, single phase transformer has the following circuit model parameters: R¡ = 0.2…
A: As per the information given in the question the circuit will be,
Q: A 45KVA, single-phase transformer is tested on both open-circuit and short-circuit conditions,…
A:
Q: A single phase transformer is rated 2400V/240V, 500kVA 50HZ yields the following primary side…
A: Solution Given data, Vbase =2400 V Sbase =500×103 VA base values can…
Q: The equivalent circuit of a 22KVA, 11700/520 V, 60HZ, single-phase loaded transformer when referred…
A: In this question we need to find a voltage regulation of the given transformer.
Q: hree single-phase transformers, each rated at 12 kVA, 120/240 V, 60 Hz, are connected to form a…
A: Here, we have given three single-phase transformers and the power rating and the voltage rating of…
Q: 6. A 25 kVA, 2300/230 V, single phase transformer has the following parameters: R1 = 0.8 Ω, X1 = 3.2…
A:
Q: A 2.5 kVA, 200v/40V single-phase transformer has the primary resistance and reactance of 3 and 12 0,…
A: Answer
Q: The parameters of a 1200/300V. 50HZ single phase transformer are given below: R-5N, X-10 fn, R 0.3…
A: The equivalent circuit of a transformer represents the behavior of the transformer with the help of…
Q: Reference bus Primary Secondary 7. A 3-phase transformer having zero sequence impedance of zo,has…
A: From the Zero sequence networks of three phase Transformer
Q: 43. A 250KVA, 2000/400V, single phase transformer achieved its variable loss equal to its fixed loss…
A: Given information about a single phase transformer: Rated power S=250 KVA. The induced EMF ratio is…
Q: A 2.5 kVA, 200V/40V single-phase transformer has the primary resistance and reactance of 3 and 12 0,…
A: “Since you have asked multiple question, we will solve the first question for you. If you want any…
Q: A 20kVA, single-phase transformer is tested on both open-circuit and short-circuit conditions,…
A:
Q: 1. A 30KVA, 6000/230V, 50Hz single phase transformer has HV and LV winding resistances of 10.2Ω and…
A: Given information about a single phase transformer is, Rated output power S=30 KVA. Induced EMF…
Q: A 45KVA, single-phase transformer is tested on both open-circuit and short-circuit conditions,…
A:
Q: The equivalent circuit of a 22KVA, 11700/520 V, 60HZ, single-phase loaded transformer when referred…
A: The equivalent circuit of a 22KVA , 11700/520 V, 60Hz, Single-phase loaded transformer.
Q: A 55KVA, single-phase transformer is tested on both open-circuit and short-circuit conditions,…
A:
Q: Power transformer A, has Rated power of 150MVA. Line voltage of 330/66 kV Frequency=50Hz Connection…
A: Active Power across the Load = Apparent Power ×power factor ---- 1) Putting value in equation -1)…
Q: Question 1 A 132/33 kV 250 MVA single-phase step-down transformer has the following parameters: R1 =…
A:
Q: Q1// A 150 kVA, 2400/240V, single phase transformer has the following circuit model parameters: R, =…
A: The rating of the transformer is 150 KVA, 2400/240 v Transformation Ratio (K) = V2/V1 The total iron…
Q: 2. We are given a system involving a step transformer with the one-line diagram shown in Figure. 1.…
A:
Q: Calculate the full-load primary and secondary currents of a 5 kVA, 2400/120 V, transformer.
A:
Q: Q4: A 2.5 kVA, 200V/40V single-phase transformer has the primary resistance and reactance of 3 and…
A: To find the equivalent impedance of single phase transformer referred to the primary and secondary…
Q: Q/ 30-kVA, 2200/220-V, 50-Hz distribution transformer is tested for efficiency and regulation as…
A:
Q: A 2.5 kVA, 200V/40V single-phase transformer has the primary resistance and reactance of 3 and 12 Q,…
A: Transformer: Transformer is a static electrical device which transfers power from one circuit to…
Q: A 2.5 kVA, 200V/40V single-phase transformer has the primary resistance and reactance of 3 and 12 n,…
A: Given:- KVA=2.5 V1=200volt V2=40volt R1=3ohm X1=12ohm R2=0.3ohm X2=0.1ohm
Q: Q4: A 2.5 kVA, 200V/40V single-phase transformer has the primary resistance and reactance of 3 and…
A:
Q: A 30KVA, single-phase transformer is tested on both open-circuit and short-circuit conditions,…
A: given single phase transformer
Q: The constant of a 37.5KVA 50-cycle, 600/240V transformer are as follows: High side effective…
A: The data given in the question are as follows: 37.5kVA,50Hz,600/240V, R1=0.052Ω, X1=j0.12Ω,…
Q: a single-phase 250KVA, 11kV/2.2kV, 60HZ transformer has the following parameters. RHv = 1.3 0 RLv =…
A: Note: According to our policy i am solving the first three questions only Answer(a) Answer(b) As…
Q: A 30KVA, single-phase transformer is tested on both open-circuit and short-circuit conditions,…
A: Given, output S = 30 kVAopen circuit losses or iron loss P = 185 Wshort circuit losses or copper…
Q: a single-phase 250KVA, 11kV/2.2kV, 60HZ transformer has the following parameters. RHy = 1.3 Q RLy =…
A: Given data Single phase rating is S = 250 KVA Frequency is F = 60 Hz Calculating k k=2.2 KV1.1…
Q: A 35kVA, single phase transformer is tested on both open circuit and short circuit conditions,…
A:
Q: Q4. A 100KVA, 200/4000V Y-A transformer has per phase in per-unit system Regpa"0.3, Xegga"0.4,…
A: Given: A 100 kVA, 200/4000 V Y-Δ transformer has per phase in the per-unit system Req.pu=0.3…
Q: A 15 kVA, 6000/415 V transformer is to be tested to determine its excitation branch components, its…
A: As per the guidelines of Bartley we supposed to answer first three subpart only for solution of…
Q: A 250kVA, single phase transformer is designed to have a resistance of 1.5% and maximum efficiency…
A: Consider the resistance is 1.5% The kVA is 250 The load is 160 kW The power factor is 0.8 W
Q: A 35KVA, single-phase transformer is tested on both open-circuit and short-circuit conditions,…
A: The problem is from machine. The calculation is shown in the next step
Q: A 10KVA, single-phase transformer has a turns ratio of 12:1 and is supplied from a 2.4 kV supply.…
A: Given values are - S=10kVAN1N2=V1V2=121V1=2.4kV
Q: Q1// A 150 kVA, 2400/240V, single phase transformer has the following circuit model parameters: R¡ =…
A:
Q: The exciting curent of a lø, 10 kVA, 2200/220 V, 60 Hz transformer is 0.25 A when measured on the…
A: Let the base values are, Pbase=10000 VAVbase,H=2200 V=1 pu Vbase,L=220 V=1 pu The value of the…
Q: hms is connected on the secondary side, calculate the primary current, the load current, and the
A:
Q: Solve the following problems with complete solutions and units using two(2) decimal digits. Use your…
A: In this question we will find secondary voltage with rated primary voltage and hence the regulation…
Q: Q1// A 150 kVA, 2400/240V, single phase transformer has the following circuit model parameters: R¡ =…
A:
Q: Draw the equivalent circuit of a 10 KVA, 1940 / 490 V 1-phase transformer with R1=0.35 ohms,…
A: Equivalant resistance seen from primary =primary winding resistance +secondary winding resistance…
Step by step
Solved in 2 steps
- PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
- A Transformer with 10:1 ratio and rated at 50-kVA, 2400/240-V, 50-Hz is used to step down the voltage of a distribution system. The low-tension voltage is to be kept constant, if the transformer has: R = 2.2 0, R2 = 0.014 Q, X, = 4.1 0, X2 = 0.03 0, then, a. What load impedance connected to low-tension side will be loading the transformer fully. b. Calculate the equivalent resistance as referred to primary. c. Calculate the equivalent reactance as referred to primary. d. Calculate the equivalent impedance as referred to primary. e. Calculate the total Cu loss.A single phase transformer is rated 2400V/240V, 500kVA 50HZ yields the following primary side equivalent parameters R=19ohm, X=0,148ohm, G=4,25x10^-4 S and B=4,14x10^-3 S. By using base values calculate per-unit values for primary side of the transformer (Vbase=2400V, Sbase=500x10^3 VA)Rated values of an ideal single-phase transformer; 3000VA, 380V/220V’ tour. If the network frequency isIt is 50Hz. The transformer is assumed to be lossless. Iron of this transformerthe flux density in its core is a maximum of 1.2 T. Iron core rectangular section and dimensions;It is 10cm and 14cm in shape. Maximum common flux of transformer, number of primary winding, secondarycalculate the number of winding and the ratio of the number of winding.
- Primary side-reduced equivalent circuit parameters of a 25 KVA, 50 Hz, 4000/400 Volt transformer R1 = 32 Ω, X1 = 45 Ω, Rc = 250000 Ω, R2 '= 66.14 Ω, X2' = 79.34 Ω, Xm It is given as = 30000 Ω. Since the secondary of the transformer is fed at a full load rated voltage with an advanced power factor of 0.9, for these operating conditions; a) Calculate the primary voltage using the T equivalent circuit. (Only the amplitude of the voltage and the phase value will not be entered.) b) Calculate the efficiency of the transformer. c )Calculate the voltage regulation of the transformer.A transformer of 100MVA, 60Hz, 138/69 kV, works as step down, has the following parameters: r1 = 0,06 ohm; XL1 = 0,08 ohm; r2 = 0,03 ohm; XL2 = 0,04 ohm. When the transformer is at rated load and assuming that the voltage at the terminals and the induced voltages are in phase, calculate: The relation between the primary and secondary induced electromotive force (emf) and between respective terminal voltages. Explain the results obtained.Given a transformer (single-phase, 10kVA, 2400/240V, 60Hz) Z1 = 5.2 + j12.5 ohms; Z2 = 0.06 + j0.12 ohm. When operating at rated primary voltage and frequency, the transformer delivers rated current to its load at 0.8 pf LAGGING. Solve for the load voltage in VOLTS - (Neglecting the no-load current.)
- 630kVA 31500/400 DY 50Hz transformer has no load and short circuit tests power measurements are given as 1kW and 20kW respectively. Under the fourth of the nominal load with 0,85 capacitive power factor, calculate the efficiency of the transformer at nominal voltage as %?A transformer with a 10:1 ratio and rated at 60kVA, 2200/220V, 60Hz is used to step down the voltage of a distribution system. The low tension voltage is to kept constant at 220V. (a) What load Impedance connected to the low-tension side will be loading the transformer fully at 0.8 power factor (lag) ? (b) What is the value of this impedance referred to the high tension side?A 20-kVA 8000/277-V distribution transformer has the following resistances and reactance: RP = 32 Ω RS = 0.05Ω X P = 45Ω XS = 0.06Ω RC = 250 kΩ X M = 30 kΩ The excitation branch impedances are given referred to the high-voltage side of the transformer. (a) Find the equivalent circuit of this transformer referred to the high-voltage side. (b) Find the per-unit equivalent circuit of this transformer. (c) Assume that this transformer is supplying rated load at 277 V and 0.8 PF lagging. What is this transformer’s input voltage? What is its voltage regulation? (d) What is the transformer’s efficiency under the conditions of part (c)?