A 50m steel tape weighs 0.05 kg/m and is supported at its end points and at the 10m and 30m marks. If a pull of5 kg is applied, determine the following. a. Correction due to sag between the 0m and 10m marks, 10m and 30m marks, and the 30m and 50m marks. b. Correction due to sag for one tape length c. Correct distance between the ends of the tape

A 50m steel tape weighs 0.05 kg/m and is supported at its end points and at the 10m and 30m marks. If a pull of5 kg is applied, determine the following. a. Correction due to sag between the 0m and 10m marks, 10m and 30m marks, and the 30m and 50m marks. b. Correction due to sag for one tape length c. Correct distance between the ends of the tape

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

CORRECTION DUE TO SAG. A 50-m steel tape weighs 0.04 kg/m and is supported at its end points and at the 8-m and 25-m marks. If a pull of 6 kg is applied, determine the following:a) Correction due to sag between the 0-m and 8-m marks, 8-m and 25-m marks, and the 25-m and 50-m marks.b) Correction due to sag for one tape length.c) Correct distance between the ends of the tape.
A rectangular, tied column 480 mm wide along x-axis and 540 mm wide along y-axis is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia. ties. Using f'c = 21 MPa, calculate the nominal axial strength at balanced condition in kN with bending about the x axis. Write your answer with 2 decimal places only.
A square, tied column 410 mm wide is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia. ties. Using f'c = 25 MPa, calculate the nominal axial strength at balanced condition in kN with bending about the x axis. Write your answer with 2 decimal places only. Correct Answer: 1,513.80 ± 1.5
2. A 50- m steel tape weighs 0.04 kg/m and is supported at its end points andat the 9-m and 30- m marks. If a pull of 6kg is applied, determine thefollowing:a) correction due to sag between the 0-m and 9- m marks, 9-m and 30-mmarks, and the 30- m and 50- m marks.b) correction due to sag for one tape lengthc) correct distance between the ends of the tape.
A heavy 50-m tape having a cross-sectional area of 0.06 cm^2 has been standardized at a tension of 4.5kg. If E=2.10x10^6 kg/cm^2, determine the elongation of the tape if a pull of 16kg is applied.
A T-shaped bracket supports a 288-N load as shown. Determine the magnitude(N) of the vertical reaction at C when α = 25°, x = 137.74 mm, y = 213.66 mm, and z = 300 mm. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the vertical reaction at C using either U if upward or D if downward.
A square, tied column 390 mm wide is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia ties. Using f'c=21 MPa, calculate the nominal axial strength at balanced condition in KN with bending about the x-axis. Write your answer with 2 decimal places only
If the resultant force acting on the bracket isrequired to be a minimum, determine the magnitudes of F1and the resultant force. Set Φ = 30°.
The standard load is 100kN. Given that n=4 and α=1, calculate EALF 80.
A 30-m steel tape weights 1.05 kg and is supported at its end points and the 10-m and 25-m marks. If a pull of 6.0 kg is applied at the ends of the tape, the correction due to sag for a full tape length is ?
SURVEYING A 50m tape weighing 0.143slug has a standard pull of 5.5kg. The tape’s cross-sectional area and modulus of elasticity are 0.03cm^2 and 200GPa, respectively. What pull, in kg, is required in order that the effect of sag will be eliminated when the tape is supported at end points only.
A square, tied column 410 mm wide is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia. ties. Using f'c = 23 MPa, calculate the nominal axial strength at balanced condition in kN with bending about the x axis. Write your answer with 2 decimal places only. ANSWER : 1392.69KN