A 6-bit D/A converter having 320 k2 resistances is in LSB position. The converter is designed with weighted resistive network. The reference voltage is 10 V. The output of the resistive network is connected to an Op-amp with a feedback resistance of 5 k 2. What is the output voltage for a binary input of 11010? 4.5 V -9 V O 9 V

A 6-bit D/A converter having 320 k2 resistances is in LSB position. The converter is designed with weighted resistive network. The reference voltage is 10 V. The output of the resistive network is connected to an Op-amp with a feedback resistance of 5 k 2. What is the output voltage for a binary input of 11010? 4.5 V -9 V O 9 V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Determine the output voltage of an op-amp forinput voltages of Vi1=150μV, Vi2=140μV and CMRRs of100 and 105. (Given Ad =4000) Vd=? Vc=?
Q4/A)- Show the connection of three combination op-amp stages using an LM348 IC to provide outputs that are 110, 1681, and 420 times larger than the input. Use a feedback resistor of Rf = 400 k? in all stages, while can use only (R= 40 k? for first stage), (R= 10 k? for second stage), and (R= 20 k? for third stage
please need correct answer and fast Q3) For an Operational Amplifier if CMRR = 140dB and Common mode gain ACM is 0.030, what will be the value of Open loop differential gain Aol? a) 21 b) 4.2 c) 300000 d) 30000
Without writing or drawing tools to lean on, you must use words, not equations, graphs or schematics in your explanation. The current in a differential pair of transistors swings between the two sides of the transistor pair as the input voltage swings between the inputs. The output voltages of course follow the current inversely. Is this swing of current related to one of the chief advantages of differential operation, the elimination of common mode signals? Keep in mind, there is a restricted range of allowed current (and voltage) swing to keep the amplifier operating in a linear way
For the circuit shown below, if the differential gain (?? ) of the op-amp is (50000) and the CMRR in (db) is (34). Find the output voltage (v_out).
With the given circuit, you are tasked to do the ff: a. Write the node-voltage equations (where there must be one for eac input terminal of the op amp) b. The load current can be expressed as iL = AVin + BVL b.1 What is the expression for A? b.2 What should be the condition of resistors R1, R2, R3, & R4, so that B is zero? (which means this condition will allow iL depend only on Vin and not on RL)
What are the output current and output resistance of the current source as shown if VDD = 10 V, R4 = 2 MΩ, R3 = 1 MΩ, RS = 120 kΩ, Kp = 750 μA/V2, VT P = −0.75 V, and λ = 0.01 V−1?
An amplifier is formed by cascading two operational-amplifier stages, as shown (a). (a) Replace each amplifier stage with its two-port representation. (b) Use the circuit model from part (a) to find the overall two-port representation (Av, Rin, Rout) for the complete twostageamplifier. (c) Draw the circuit of the two-port corresponding to the complete two-stage amplifier.
An amplifier is formed by cascading three identical operational-amplifier stages, as shown . (a) Replace each op amp circuit with itstwo-port representation. (b) Use the circuit model from part (a) to find the overall two-port representation (Av, Rin, Rout) for the complete three-stageamplifier. (c) Draw the two-port circuit corresponding to the complete three-stage amplifier.
a. small signal transconductance (in uS) of the PMOS b. the output impedance (in kΩ, 2 decimal places) of the PMOSGiven that: VTH = -0.5V, k = 2mA/V2, λ = 0.05, VGS = -0.9V, and VDS = -0.7V.
Show the connection of three combination op-amp stages using an LM348 IC to provide outputs that are 110, 1681, and 420 times larger than the input. Use a feedback resistor of Rf = 400 k? in all stages, while can use only (R= 40 k? for first stage), (R= 10 k? for second stage), and (R= 20 k? fot third stage)
Suppose we have a signal source with an internal (i.e., Thévenin) impedance that is always less than 1000 Ω, but is variable over time. Using the components listed in TableP13.36 , design an amplifier that produces an amplified version of the internal source voltage. The voltage gain should be −20±5 percent.