A 60mm diameter shaft is subjected to an axial force of 10kN. The collar of the shaft (A) has a diameter of 100mm, and is supported by a rigid steel support. a. Determine the axial stress in the shaft. b. Determine the bearing stress between the collar (A) and the support. c. Determine the maximum shear stress between the collar and shaft. 2.5 mm 60 mm 100 mm 10 kN 2.5 mm 15 mm

A 60mm diameter shaft is subjected to an axial force of 10kN. The collar of the shaft (A) has a diameter of 100mm, and is supported by a rigid steel support. a. Determine the axial stress in the shaft. b. Determine the bearing stress between the collar (A) and the support. c. Determine the maximum shear stress between the collar and shaft. 2.5 mm 60 mm 100 mm 10 kN 2.5 mm 15 mm

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 76 kN and torques TB = 15 kN-m and TC = 4 kN-m, which act in the directions shown. Determine the normal stress x at point H.
QUESTION 2) A bending moment of M=4 kNm, tan alpha (α)=0.577, acts on the section in the figure. Unbiased Determine the position of the axis and draw the stress distribution in the section
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb>ft2, determine the state of stress at points C and D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe.
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
knowing that P = 18 Kips, determine the maximum stress when r = 0.45 in and r = 0.70 in
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-sectional is square, 0.55 in. On each side.
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
If d = 450 mm, determine the absolute maximum bending stress in the overhang beam.
If the output torque on the CD shaft is T ́ = 75 N-m and the motor rotates at 175 rpm, determine the power delivered by the motor in watts. • Is there torque at the BE and CF ends? • Calculate the maximum shear stress in the AE axis.
g. What is the moment of inertia (I) about the neutral axis of the section? (in in^4) h. What is the first moment of an area (Q) about the neutral axis of the section? (in in^3) i. What is the maximum shearing stress (fv) of the beam? (in psi) j. What is the maximum flexural stress (fb) of the beam? (in psi)