12B6 kN3 mThe beam is supported by two solid rods AB and CD, both rods have the same cross-sectionalarea (A). Determine the position (d) of the 6-kN load so that the average normal stress in rodAB is 20 MPa and the average normal stress in rod CD is 10 MPa. *

Answered: Image /qna-images/answer/049ffafc-9f82-4b4b-aec8-107403043a52.jpg

Answered: 12 B D 6 kN A 3m The beam is supported…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam has a uniform concentrated load (Pu) at midspan and has a fixed support at both end. If the beam properties are given below, what is the stress at bottom of the beam section at 2.76 from the support. (MPa)
A beam is being supported by the two rods, A-B and C-D that have a cross sectional areas of 14 mm2 and 21 mm2, respectively. Determine the magnitude of the triangular load w such that the normal stress in each rod does not exceed 350 kPa.
The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load P as shown. a. Determine the torsional shear stress at Point A (50mm from the center) and Point B (on the Surface) b. Determine the absolute maximum torsional shear stress in the shaft. c. sketch the state of stress at point A and draw its corresponding Mohr’s Circle of stress. compute the principal stresses and maximum in-plane stress. T=10.38kN-m
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28 and fy is 420. 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam
the cantilever has a partially hollow circular cross section. If the admissible normal stress is 140 MPa, determine the maximum value of Wo (distributed load intensity) that the beam can support. express your answer in KN / m
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 16 kips, F2 = 30 kips, and the normal stress in each rod must be limited to 18 ksi, determine the minimum diameter d1 required for rod (1).
For given cross section with moment have 16 KN-m, kindly calculate the following ÷ a) normal stress at B b) normal stress at D
The rod has a diameter of 40 mm. It is subjected to the force system Fx=1300 N=1300 N, Fy=500 N=500 N, Fz=800 N=800 N. Determine the normal stress that acts at point B. Determine the shear stress (τB)xy that acts at point B. Determine the shear stress (τB)xz that acts at point B.
f. What is the moment of inertia (I) about the neutral axis of the section? (in in^4) g. What is the first moment of an area (Q) about the neutral axis of the section? (in in^3) h. What is the maximum shearing stress (fv) of the beam? (in psi) i. What is the maximum flexural stress (fb) of the beam? (in psi)
Question ) Forces of F1=3 kN from point B in the z direction, F2=5 kN from point C in the z direction and F3=8 kN in the y direction are acting on the arm in the figure. The lengths of the arm are also given as L1=0.18 m and L2=0.17 m. It is desired to determine the stress state of point A on the a-a section taken from the arm. The radius r of the section is r=0.3 m and the shear modulus of the arm material is G=79 Gpa. According to this; Question 1-A) Find the shear stress due to the shear force at point A. (Write your result in MPa.Question 2-B) Find the shear stress due to the torsional moment at point A. (Write your result in MPa.Question 3-C) Find the total shear stress at point A. (Write your result in MPa)Question 4-D) Find the normal stress caused by the normal force at point A. (Write your result in MPa Question 5-E) Find the normal stress caused by the bending moment at point A. (Write your result in MPa.)Question 6-F) Find the total normal stress at point A. (Write your…
Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-section is square, 0.45 in. on each side. Draw free-body diagram.
A force of 3000N is acting on the orange plank which is attached to the pin as shown in thefigure. a.) If the thickness of the orange plank is 75mm and the pin has a diameter of 20mm,compute the bearing stress acting between the plank and pin. b.) Compute theshearing stress acting on the pin and c.) the normal stress of the orange plank if it hasa width of 500mm.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

12 B D 6 kN A 3m The beam is supported by two solid rods AB and CD, both rods have the same cross-sectional area (A). Determine the position (d) of the 6-kN load so that the average normal stress in rod AB is 20 MPa and the average normal stress in rod CD is 10 MPa.