A 6A current source drives a load consisting a parallel combination of R1 = 60 Q and R2 = 10 Q. Determine the current 11 through R1.Select the correct response:6 ampnone of the above1 amps5.143 amps.0.857 amps

The correct answer is Option E. Explanation provided below. Please go through it.

A 6A current source drives a load consisting a parallel combination of R1 = 60 N and R2 = 10N. Determine the current 11 through R1. Select the correct response: 6 amp none of the above 1 amps 5.143 amps. 0.857 amps

A 6A current source drives a load consisting a parallel combination of R1 = 60 N and R2 = 10N. Determine the current 11 through R1. Select the correct response: 6 amp none of the above 1 amps 5.143 amps. 0.857 amps

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 8PP: In an R-L parallel circuit, ET=48 volts, IT=0.25 amps, R=320. Find XL.

See similar textbooks

Related questions

Q: 4) A 2300/230V , 60Hz transformer takes 0.5A at a power factor of 0.25 on open circuit when supplied...

Q: 20 μΑ 2.7 k 2 RB + B VCE = 7.3 V %3D o 2.1 V 0.68 kN

Q: A power plant comprises three turbine-generators rated 1000 MW, 800 MW and 500 MW respectively. The ...

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts fo...

Q: 4.47.3 In the circuit shown in the image below, if R1 = 38 Q, R2 = 37 Q, and 1 = 1. A, determine the...

A: Given circuit shown R1=38 ΩR2=37 ΩI1=1.9 A

Q: What exactly is a prime implicant?

A: The solution is given below

Q: Which of the following term is an electrical device that can store electric charges? Select one: a....

Q: Q5: In the circuit of Fig. 5, if v 6 V, find i,. Fig. 5

Q: 1. Draw the amplitude spectrum of the following signal (if w=100T) 2V 4V (cos 2ut cos 4u cos but 1x3...

A: Given signal vt=2Vπ-4Vπcos2ωt1×3+cos4ωt3×5+cos6ωt5×7+......ω=100π

Q: Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 6...

Q: 10.Analyze the following sequential circuits (derive the state transition table and the state diagra...

A: This is a problem of digital circuit. The solution is given below

Q: A coil has inductance of 5 H and resistance 20 ohms and voltage connected of 100 volt battery. Find...

A: The inductance and impedance of the coil is given as: Z=R+jωL=20+j2π×50×5=20+j1570.796 Ω=1570.923∠89...

Q: Given the expression U = (A'+B')(C+D), implement the circuit using one type of logic gate and use mi...

A: Given expression U=(A'+B')(C+D)

Q: The equivalent resistance of three resistors

Q: 5. Determine the transfer function using Mason's Gain formula GA G G2 R(s) No N N Ge Gs Fig. 5

Q: Solve the Laplace Transform L(cos(at)sinh(at))

Q: In the balanced three phase power measurement using two wattmeter method, each wattmeter reads 24 kW...

Q: Which IC technology has the lowest power dissipation in general?

Q: Determine the proper size of copper wire conductor necessary to apply a 750 W electric motor that is...

A: It is given that: P=750 WL=100 feetVpanel=120 voltsVdrop=1.2 volts

Q: Hw)ALow Pass Filter Sircuit Conlis ting of aresistor of 5052 inseries with a Cafacitor of 5onF is Co...

Q: Use current divider rule to determine the currents in two resistors of 302 and 602 connected in para...

A: Current divider rule applies when there are two or more resistors in parallel. In the given question...

Q: Two conductors carrying 60 A and 75 A, respectively are placed 10 cm apart. Find the force between t...

A: We need to find out force between wire for given current

Q: 4.71 In the circuit shown in the image below, if R1 = 3.1 kQ, R2 = 57 kN, and V1 9.5 V, determine th...

Q: Vcc Ic 2.2 k2 RB + VCE = 7.2 V B = 20 µA %3D IIE = 4 mA 812 Kohm 100 Kohm

Q: FNo ho Qnd thu Maaimum Bwen then Cror Bo Trois kred.

Q: wo infinite sheets carrying currents are parallel to each other in xy plane, and they are separated ...

A: Given that charge K=Kx

Q: Calculate the Fourier transform

A: In this question, Find the Fourier transform of the given signal. We are solving this problem usin...

Q: In your own words, Explain each principles of signal communications in Military.

A: signal communication A signal is composed of data which may be an electrical or electromagnetic the ...

Q: Vcc +10 V R 47 kſ2 Re 4.7 kl Bpc = 150 REI 470 N R2 * 10 k2 470 N 1V, 0.3V, 5.02V 0.3V, 1V, 5.02V O ...

A: Note : After analysing the given circuit we come to know that in 1st option VB is wrongly mentioned....

Q: What is the output voltage(R1) on the 1st half cycle? * C1 Y D1 R1 12V V3V

A: The solution is given below

Q: Q9: Determine how much power is absorbed by R, in the circuit of Fig. 9. + 9 V R. 10 mAt) 2 k2 1 kN ...

Q: Draw the low-level and high level AM circuits. (transistor based).

A: Amplitude Modulation- When Amplitude of Carrier signal is changing according to Amplitude of Message...

Q: Subject Electrical Apparatus and Devices the volts per unit of a 60hz,13800/460v transformer is 6.57...

Q: 3- Use the time-shifting property (Eq. number 2 in Fourier transform pairs table) to show that if g(...

A: As per our company guidelines we are supposed to answer only first question kindly repost other ques...

Q: Mesh Analysis - cont. Example 2 (ex (3.6) – p(91) Use mesh analysis to find current I. i2 10 Ω 24 Ω ...

A: Given circuit, Here, Io=i1-i2

Q: With the aid of a diagram explain bourdon gauge and how it works !!. Explain the principle of operat...

A: Bourdon gauge : A bourdon gauge is a mechanical instrument which is used to measure the pressure mai...

Q: X1(s) 1. Solve for G, (s) G2(s) F(s) ' X2(s) F(s) x,(t) X:(t) K,-I N/m K2-1 N/m fin f,= 2 N-s/m M, =...

A: Solution- Using newton's law, we had the equations of motion for the given system, m1x1''+fv1+fv2x1...

Q: HW, Find the Stability of the system as shown in Pig. by usiny Routh stabilly Criterion. Routh stabi...

A: The closed loop transfer function is given as: C(s)R(s)=3s(s+1)(s+2)+3 The characteristic equation i...

Q: An optical intensity of 1 W/cm2 is incident on an intrinsic GaAs detector. The photon energy is 2 eV...

A: Given - Optical intensity = 1 W/cm2 Photon energy = 2 eV Absorption coefficient = 4+10^6 m^-1 ni = ...

Q: A unity feedback system has been operated for 5 years and need to be evaluated. It has an open loop ...

A: Solution- Gs =Ks(s+1) (s+3) a) for 4.32% overshoot , e-πξ/1...

Q: H,

Q: Compute the frequency response H¿(jw) = Vo/Is 2mH ll Is s (1) 1KN 4KN; v. 1ΚΩ

A: The solution is given below

Q: Ohm's Law states that: Voltage = current x resistance Voltage = current / resistance Current = volta...

Q: 4.57.3 In the circuit shown in the image below, if Rx= 7.8 Q, R1 = 10.3 Q, and V1 57 V, determine th...

Q: Q2/ For the current shown in the figure below, find the charge waveform and then find the value of c...

A: The solution is given below

Q: Ir. Razi has been asked to build one controller in order to control the tilt angle

Q: 10.Analyze the following sequential circuits (derive the state transition table and the state diagra...

A: The solution is given below

Q: A tungsten lamp filament has a temperature of 20.5 degrees Celsius and a resistance of 500 ohms when...

Q: PROBLEM SET:The potential across the hygrometer transducer is given as a function of resistance, R. ...

A: Draw the graph between voltage rating and resistance for the given values. Keep R value in X axis an...

Q: 3. A factory's separately excited DC generator has an armature resistance of 0.250. The machine is d...

A: Separately excited DC generator- Machine whose field winding is energize by an external DC supply so...

Q: Refer to Figure below, determine v(t) and i(t). 4 2 + v, = 5 cos(10t) 0.2 H

A: Given circuit:

Concept explainers

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.

Question

A 6A current source drives a load consisting a parallel combination of R1 = 60 Q and R2 = 10 Q. Determine the current 11 through R1.
Select the correct response:
6 amp
none of the above
1 amps
5.143 amps.
0.857 amps

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step_1

VIEW

Step_2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Suppose that the voltage source has an internal series resistance of 50 Ω. How would the outputvoltage be affected (assuming that R1 and R2 are the same as you specified earlier)? Work out your resultsfor both the ideal voltage source and for the voltage source with the internal impedance. R1 and R2 are both 3 Ohms and Vin = 10 V
Please kindly help me to answer this QUESTION. Thank you very much! A millivoltmeter has a resistance of 2.5 ohms and deflects full scale on 50mV. (a) What should be the resistance of a shunt if the instrument is to be used as a 1 - amp ammeter? (b) Repeat part (a) neglecting the moving - coil current.
1. What type of circuit is this? 2. What is the voltage across R1 ? 3. What is the total current flow (amps) in the circuit? Thanks!
Using only source transformation and without eliminating ix, reduce the circuit in Figure to a single voltage source and a single resistor, then obtain ix using Ohm's law. A) What is the value of the source voltage in V and what is the value of the resistor in Ω? B) What is the value of ix in Amps?
Using only source transformation and without eliminating ix, reduce the circuit in Figure to a single voltage source and a single resistor, then obtain ix using Ohm's law. Please answer the 2 questions A) What is the value of the source voltage in V and what is the value of the resistor in Ω? B) What is the value of ix in Amps?
Hey please reply as soon as posible Using only source transformation and without eliminating ix, reduce the circuit in Figure to a single voltage source and a single resistor, then obtain ix using Ohm's law. A) What is the value of the source voltage in V and what is the value of the resistor in Ω? B) What is the value of ix in Amps?
Calculate the V1, V2, V3 and V0 values for the following cases by analyzing the circuit in the figure.a) For Rf=10kΩ;b) for Rf=22kΩ;c) for Rf=33kΩ;The supply of the opamp is ±12V.
Draw a circuit that contains a 5–Ω resistor, a 10-V voltage source, and a currentcontrolled voltage source having a gain constant of 2 Ω. Assume that the current through the resistor is the control current for the controlled source. Place all three elements in series.
. If v1 = 1 V and v2 = 2 V, find vo in the op amp circuit of Figure.(1)
Two storagebatteries, A and B, are connected in parallel for charging from a d.c. sourcehaving an open-circuit voltage of25V and an internal resistance of 2.5 .The open-circuit voltage of A is 11V and that of B is 11.5 V; the internalresistances are 0.06and 0.05 respectively. Calculate the initial chargingcurrents.
21/ Potential Divider Principle is the simplest way of producing a source of higher EMF from a source of lower EMF. Select one: True False
An AC source delivers current to two loads A and B that are connected in parallel. if the A-load current of 25 amp leads the B-load current of 42.2 amp by 45 elec deg. (A) Calculate the resultant constant (B) Determine the angle between the resultant current and an assumed A-current reference