A 6cm diameter horizontal water pipe expands to a 10cm diameter pipe. The average velocity and pressure of water before the expansion section are 7 m/s and 150 kPa, respectively. Determine the head loss in the expansion section. Use Table 2 from our Lecture for the loss coefficient. А None of the above 0.6667 m (c) 0.3333 m C D) 0.9999 m

A 6cm diameter horizontal water pipe expands to a 10cm diameter pipe. The average velocity and pressure of water before the expansion section are 7 m/s and 150 kPa, respectively. Determine the head loss in the expansion section. Use Table 2 from our Lecture for the loss coefficient. А None of the above 0.6667 m (c) 0.3333 m C D) 0.9999 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pressures at the ends of 605m long horizontal pipe flow are 350 kPa and 270 kPa. The pressure at the point between the ends is 300 kPa. The pipe is 305mm in diameter and n=0.018. Find the total headloss, amount of flow, and the slope of the egl.
Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a point upstream and 1.83 m below where the pipe discharges water into the atmosphere at the rate of 0.0556 m /s.
Q.5. Determine the velocity of the flow out of the vertical pipes at A and B, if water flows into the Tee at 8 m/s and under a pressure of 40 kPa. Assume negligible head loss.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. a) Determine the head loss in the “smooth” pipe in meters if the friction factor is 0.014. b) What gage pressure p1 in kPa, is needed to provide the given flow rate?
A circular door having a diam. of 3m closes a horizontal duct from a small diam. as shown. The center of the door is 4.5m below the dam’s water level. Assuming the unit weight of water is 9.79 kN/m3. Compute the hydrostatic force acting on the door.
Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, pipe 3connected in series with length of 170 m, 300 m, 210 m respectively. Thedifferent in water surface levels in two reservoirs is 12 m. The friction coefficientfor pipe 1, pipe 2 and pipe 3 are 0.0052, 0.005 and 0.0048 respectively. Based onTable 2 and the setting given, determine the flowrate of the flow if the entranceloss coefficient is 0.25 considering :(i) minor losses; and(ii) neglecting minor losses pipe 1 =230(mm) Pipe 2 =330(mm) Pipe 3 = 430(mm)
Water at 20°C ( ρ= 999.7 kg/m3 and μ=9.7720 x10-4 kg/m · s) is flowing steadily in a hexagonal cross sectional pipe b=1.5cm, 20-m-long at an average velocity of 1.2 m/s. Determine: (a) Hydraulic diameter. (b) The pressure drop. (c) The head loss. (d) The pumping power requirement to overcome this pressure drop.
A 300mm by 460mm rectangular pipe carries oil at 105 kpa absolute and 20c through 460m with an average velocity of 2.97 m/s. determine the loss and the pressure drop, assuming the pipe is horizontal and the size of the surface imperfections is 0.00055m.
A masonry dam having a sheet piling cutoff at the upstream and is located at a reservoir site as shown in the figure. Nf= 4; Nd= 10 and K= 0.003m/min 1) compute the seepage discharge in cu MTR/day 2) compute the uplift force acting on the base; 3) compute the exit or escape gradient of the water at the downstream tip of the dam if the length of the flow field is equal to 1.80m
1. Compute the head loss in a pipe with diameter 300 mm for a length of 15,000 meters and carrying a flow of 0.097, if f=0.02. (Hint: Use h=(0.0826fL(Q^2))/(D^5)
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m3s is to occur in the cast-iron pipe? Use f = 0.021 for all pipes. Draw the HGL and the EGL, including changes in slope due to head loss. Neglect minor losses.
Water flows in a wide channel at Fr=4.5 and y1 = 2.40 m. If the flow undergoes a hydraulic jump, calculate: y2