Answered: A 6kg hoop 3m in diameter rolls down a…

A 6kg hoop 3m in diameter rolls down a plane inclined 40 degrees. At the bottom of the incline, what is it's a.) total kinetic energy b.) angular speed and c.) linear speed. Ignore friction. 3 m

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Rotational Dynamics

Section: Chapter Questions

Problem 12WUE: A bowling ball of mass 7.00 kg is rolling at 3.00 m/s along a level surface. Calculate (a) the balls...

See similar textbooks

Related questions

Q: Calculate the rotational inertia of a wheel that has a kinetic energy of 18.5 kJ when rotating at…

A: Answer

Q: A car is designed to get its energy from a rotating flywheel with a radius of 1.50 m and a mass of…

A: Write the given values of the problem- Radius(r)=1.50 m Mass(m)=445 kg f=5750 rev/min

Q: The figure below shows a ball with mass m = 0.390 kg attached to the end of a thin rod with length L…

A: we will use work energy theorem here. Namely change is kinetic energy will be compensated with…

Q: A 4.0kg mass is connected by a massless string over a massless and frictionless pulley to the center…

A: Mass of wheel M = 8kg Mass of object m = 4kg Radius of wheel= 0.50m Moment of inertia = 2.0 kgm2

Q: A hoop rolls down a 5.75 m high hill without slipping. Here is a link to the downhill race if you…

A: H= 5.75m

Q: A long thin hockey stick is swung through an angle of 60 degrees in 0.04s from the top of the swing…

A: Let θ denotes the angular displacement of the hockey stick. It is given as 60º. It can be expressed…

Q: The turntable in a microwave oven has a moment of inertia of 0.038 kg⋅m2 and is rotating once every…

A: Given, moment of inertia =0.038 kg.m2time period T =5.0 secwe have to calculate the kinetic energy.

Q: A cylinder rolls down a hill and around a loop as shown. It starts from rest at point A. When it…

A: For rolling motion frictional force should present.

Q: 7. A hollow ball is set rolling without slipping at 4.03 m/s on a horizontal track as shown below.…

Q: An electric motor is used to drive the shaft of a small water pumpm. During a performance test, the…

Q: A 4 kg ball with a 0.5 m radius rolls at a constant 4 rad/s. The rotational inertia of the ball is…

Q: A 280-N sphere 0.20 m in radius rolls without slipping 6.0 m down a ramp that is inclined at 31°…

A: weight of the sphere mg =280 N Radius of the sphere r =0.2 m Angle of inclination θ =310 Height of…

Q: car is designed to get its energy from a rotating flywheel (solid disk) with a radius of 1.00 m and…

Q: 3. A 2.0-kg and 0.2 m radius yoyo in form of a ring has a light string wrapped around its rim, with…

Q: Calculate the rotational inertia of a wheel that has a kinetic energy of 37.9 kJ when rotating at…

Q: 8. A person spins a grindstone with a radius of 0.16 m along its edge, making the grindstone spin…

A: (8) The given data are: r=0.16 mW=402 J Here, r denotes the radius and W denotes the workdone.

Q: A hollow ball of mass Mand radius Ris released from rest at the top of a bumpy track. The starting…

A: Given; Mass of the ball is M Radius of the ball is R Initial height is H

Q: 21 Two cylinders rotating counterclockwise around a frictionless axle, as shown are brought together…

Q: A spider climbs onto the edge of a 0.254 m radius, vertical grinding wheel just before someone turns…

Q: A disc‐shaped grindstone with a mass of 50 kg and a diameter of 0.52m rotates on frictionless…

Q: the maximum torque on the motor

A: the maximum torque on the motor is 0.03 N m

Q: A 29.3 kg wheel, essentially a thin hoop with radius 1.93 m, is rotating at 204 rev/min. It must be…

A: According to the work-energy theorem, the work that must be done is equal to the change in…

Q: Read the question carefully and give me right solution according to the question. A 1,200 kg car…

Q: TOPIC: Dynamics of Rotation Compute the rotational KE of a 25-kg wheel rotating at 6 rev/s if the…

A: Given that The mass of the wheel (m) = 25Kg Wheel rotating at 6rev/s…

Q: A 60 cm long string tied the end of a ball of mass of 0.5Kg. pushed to the duan in a horizontal…

Q: A disk of radius = 2.02 mm is attached to a high-speed drill at a dentist’s office and is turning at…

Q: When a fan is switched from medium to high the fan blade accelerates from 21.0rev/sec to…

Q: A 4.6kg block resting on a smooth horizontal surface is attached to a string that passes over a…

A: (a) Write the given parameters. m=4.6 kgr=0.48 mF=8.5 Nd=0.35 m

Q: A 5 kg cylinder 0.5 m in diameter rolls down a plane 5 m long inclined 30° with the horizontal at…

Q: A large wind turbine (typical of the size and specifications of a turbine that you see in a modern…

A: The angular velocity of the blades will be the same as the angular velocity of the central hub.…

Q: A hoop is initially at a height of 10m above the ground. It rolls down a slope with an initial speed…

A: Given:- A hoop is initially at the height h= 10 m The initial velocity of the hoop is v0 = 12 m/s…

Q: A hollow sphere rolls without slipping down a ramp that is 3.5 m long. the ramp is inclined at an…

A: Given information: Here, l is the length of the ramp and θ is the ramp’s inclination angle.

Q: A car is designed to get its energy from a rotating flywheel with a radius of 1.00 m and a mass of…

A: Given Data : The mass of the flywheel is given as m = 580 Kg. The radius of the flywheel is given as…

Q: A 260-N sphere 0.20 m in radius rolls without slipping 6.0 m down a ramp that is inclined at 31°…

Q: A potter's wheel is a thick stone of radius 0.5 m with mass 100kg. It freely rotates at 50 rpm…

A: radius (r) = 0.5 m mass (m) = 100 kg Angular speed (ω) = 50 rpm

Q: A thin uniform rod 2.40 m long weighing 135 N has a frictionless pivot at one end, allowing it to…

A: Given:- length of rod = 2.40N force on rod = 135 N angle θ = 55o The centre of mass is initially at…

Q: A 32 kg flywheel, essentially a disk of radius 1.2 m, is rotating at 3000 rev/minute. Use…

A: The work required to stop the flywheel can be given by work-energy theorem as, Here, W, K, I, m, r,…

Q: A particle with mass 0.025kg is attached to massless cord passing through a hole in the surface.…

Q: A solid sphere with radius r=2 m rolls smoothly from rest from a ramp at heighth = 10 m that is the…

A: Given: The height of the ramp is 10 m. The radius of the sphere is 2 m. The final velocity of the…

Q: A person spins a large grindstone 0.320-m radius, from rest, by placing his hand on its edge and…

A: We have to use some basic formula here is.

Q: A belt is placed around a pulley that is 30.0 cm in diameter and rotating at 275 to.. Find the…

A: Given, diameter = 30.0 cm rotating speed = 275 rpm

Q: An electric motor is used to drive the shaft of a small water pump. During a performance test, the…

A: Given, Torque on the motor shaft, τ = 5.408 N.m Electric power, P = 519.74 W

Q: A 290-N sphere 0.20 m in radius rolls without slipping 6.0 m down a ramp that is inclined at 25°…

Q: A 250-N sphere 0.20 m in radius rolls without slipping 6.0 m down a ramp that is inclined at 34°…

A: Given data: The weight of the sphere, W=250 N. The radius of the sphere, r=0.20 m. The length of…

Q: 7. [20 points] A hollow ball is set rolling without slipping at 4.03 m/s on a horizontal track as…

Question

A 6kg hoop 3m in diameter rolls down a plane inclined 40 degrees. At the bottom of the incline, what is it's a.) total kinetic energy b.)
angular speed and c.) linear speed. Ignore friction.
...
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

An athlete in a gym applies a constant force of 50 N to the pedals of a bicycle to keep the rotation rate of the wheel at 10 rev/s. The length of the pedal arms is 30 cm. What is the power delivered to the bicycle by the athlete?
A gyroscope has a 0.5-kg disk that spins at 40 rev/s. The center of mass of the disk is 10 cm from a pivot which is also the radius of the disk. What is the precession angular velocity?
Integrated Concepts Riders in an amusement park ride shaped like a Viking ship hung from a large pivot are rotated back and forth like a rigid pendulum. Sometime near the middle of the ride, the ship is momentarily motionless at the top of its circular arc. The ship then swings down under the influence of gravity. (a) Assuming negligible friction, find the speed of the riders at the bottom of its arc, given the system's center of mass travels in an arc having a radius of 14.0 m and the riders are near the center of mass. (b) What is the centripetal acceleration at the bottom of the arc? (c) Draw a free body diagram of the forces acting on a rider at the bottom of the arc. (d) Find the force exerted by the ride on a 60.0 kg rider and compare it to her weight. (e) Discuss whether the answer seems reasonable.
A bicycle is turned upside down while its owner repairs a flat tire on the rear wheel. A friend spins the front wheel, of radius R, and observes that drops of water fly oil tangentially in an upward direction when the drops are at the same level as the center of the wheel. She measures the height reached by drops moving vertically (Fig. P10.74). A drop that breaks loose from the tire on one turn rises a distance h1 above the tangent point. A drop that breaks loose on the next turn rises a distance h2 h1 above the tangent point. The height to which the drops rise decreases because the angular speed of the wheel decreases. From this information, determine the magnitude of the average angular acceleration of the wheel.
While exercising in a fitness center, a man lies face down on a bench and lifts a weight with one lower leg by contacting the muscles in the back of the upper leg. (a) Find the angular acceleration produced given the mass lifted is 10.0 kg at a distance of 28.0 cm from the knee joint, the moment of inertia of the lower leg is 0.900kg-m2 the muscle force is 1500 N, and its effective perpendicular lever arm is 3.00 cm. (b) How much work is done if the leg rotates through an angle of 20.0° with a constant force exerted by the muscle?
A car is designed to get its energy from a rotating solid-disk flywheel with a radius of 2.00 m and a mass of 5.00 102 kg. Before a trip, the flywheel is attached to an electric motor, which brings the flywheels rotational speed up to 5.00 103 rev/min. (a) Find the kinetic energy stored in the flywheel, (b) If the fly-wheel is to supply energy to the car as a 10.0-hp motor would, find the length of time the car could run before the flywheel would have to be brought back up to speed.
Semi-trailer trucks have an odometer on one hub of a trailer wheel. The hub is weighted so that it does not rotate, but it contains gears to count the number of wheel revolutions—it then calculates the distance traveled. If the wheel has a 1.15 m diameter and goes through 200,000 rotations, how many kilometers should the odometer read?
While driving his motorcycle at highway speed, a physics student notices that pulling back lightly on the night handlebar tips the cycle to the left and produces a let turn. Explain why this happens.
Describe how work is done by a skater pulling in her arms during a spin. In particular, identify the force she exerts on each arm to pull it in and the distance each moves, noting that a component of the force is in the direction moved. Why is angular momentum not increased by this action?
A bowling ball of mass 7.00 kg is rolling at 3.00 m/s along a level surface. Calculate (a) the balls translational kinetic energy, (b) the balls rotational kinetic energy, and (c.) the balls total kinetic energy, (d) How much work would have to be done on the ball to bring it to rest? (See Section 8.6.)
A wind turbine rotates at 20 rev/min. If its power output is 2.0 MW, what is the torque produced on the turbine from the wind?
The puck in Figure 10.25 has a mass of 0.120 kg. The distance of the puck from the center of rotation is originally 40.0 cm, and the puck is sliding with a speed of 80.0 cm/s. The string is pulled downward 15.0 cm through the hole in the frictionless table. Determine the work done on the puck. (Suggestion: Consider the change of kinetic energy.)