A 75 mm 75 mm -100 mm E Fig. P3.30 200 N 200 N B 750 N D 3.30 The shearing forces exerted on the cross section of a steel channel may be represented by a 750-N vertical force and two 200-N horizontal forces as shown. Replace this force and couple by a single force F applied at point C and determine the distance x from C to line BD. (Point C is defined as the shear center of the section.)

A 75 mm 75 mm -100 mm E Fig. P3.30 200 N 200 N B 750 N D 3.30 The shearing forces exerted on the cross section of a steel channel may be represented by a 750-N vertical force and two 200-N horizontal forces as shown. Replace this force and couple by a single force F applied at point C and determine the distance x from C to line BD. (Point C is defined as the shear center of the section.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A force F having a magnitude of F = 100 N actsalong the diagonal of the parallelepiped. Determine themoment of F about the point A, using MA = rB x F andMA = rC x F.
1.Curved beam ABC,AB=parabolic curve and BC is straight horizontal direction.Point B is the top of the curvature of the block with a slope of 0^o.Horizontal distance AB=6m;BC=2m and vertical distance AB=2m.The load is evenly distributed q works from A to E; the moment coupling load M and the concentrated load P with a slope of tan = 0.75 act at point C. The equation for the curvature of the parabolic beam AB is y=a+bx+cx^2. Questiona) Determine the equation of the parabolic curved cuboid ABb) Calculate all support reactions and indicate their direction
The 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel?
.15 2.16 The three forces acting on the beam can be replaced with a single equivalent force R. Determine the angle θ and R. 25kN P2 60 kN P3 80 kN 40° 50° 4 m 6 Figure P2.16 COMPANY
Can you show P2 = 0.2779P3 + 0.667P1 was solved
A certain force F has a moment of 18Q N-m clockwise about point O and 9T N-m counterclockwise about point B. If its moment about point A is zero, determine the magnitude and direction of the force. Also, determine the x-intercept of the force. (x-intercept of the force is the distance of the intersection of the line of action of the force and the x-axis, measured from the origin O). Wherein: Q=2 T=6 Example: 2QT kN = 226 kN T.Q5 m = 4.25 m
The bearing of line AB is N 48* W, and the bearing of line AC is N 35*15 E. The angle BAC is: A. 167*15' B.83*15 C. 96*45 D. 12*45
Where: P1= 5 , P2= 7.5 , P3=10 , P4: 8.5
Find the distance X1, if the moment at midspan is zero. a. 2.5 m b. 3.0 m c. 2.25 m d. 2.75 m
The roof is supported by cables as shown in the photo. If the cablesexert forces FAB = 100 N and FAC = 120 N on the wall hook at A asshown , determine the resultant force acting at A. Expressthe result as a Cartesian vector.
For the beam presented below:a) What is the degree of indeterminacy; b) Determine the moment reactions at the supports and draw the shear and momentdiagrams. (Solve by expressing the internal moment in terms of vertical reactionsat A and B, EI is constant). c) What would the shear diagram look like if a transverse load P was applied right atthe middle of the beam (Make a sketch of the new shear diagram). W (30kN/m) , L (1.9m)
4. What is the degree of curve of shear AB?