i need the answer quickly a) A simply supported beam AB, 6 m long is loaded as shown in Figure below2 kN5 kN2 kN/m1.5 mDE.B.1.5 m-3 m6 m2: Draw shear force and bending momentdiagram for beam below100KN mM 1200 kN.mA.2 m4 mm

given- a simply supported beam carrying UDL and point load required- to draw bending moment and…

Answered: a) A simply supported beam AB, 6 m long…

a) A simply supported beam AB, 6 m long is loaded as shown in Figure below 2 kN 5 kN 2 kN/m 1.5 m - D A 1.S -1.5 m- to 6 m 1- E 3 m B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: a. Determine the velocity of flow in the pipe in fps. b. Determine the discharge Q in ft^3/s. ...

A: Apply bernoulli equation.

Q: Consider the beam shown in Figure. a. Write the equations for shear and moment. b. Evaluate the shea...

Q: Explain the importance of iron and steel as a construction materials.

A: Iron and steel are used as construction material due to various engineering properties Following are...

Q: The short column below is subjected to Pu = 2200 kN. Use f’c = 28 MPa and fy = 415 MPa, Clear cover ...

Q: An unsymmetrical parabolic curve has a back tangent of -5% and a forward tangent of +3%. If the leng...

Q: 4" 16" 3 No. 8's 12" 7 ft

Q: A tank has a circular 60 mm in diameter located at its side. Its bottom is elevated 19 m above the g...

Q: In a reclamation project, the middle of a clay layer is under an initial effective vertical stress o...

Q: The following are examples of Environmental Loads except, O Snow load O Seismic load O Traffic Ibad ...

A: Given: Loads To find: Load other than environmental load

Q: 1. Convert the information given in the accompanying table from Sl units to U.S. Customary units Con...

Q: A watershed 600 ha in area experienced a rainfall of unifom intensity 2.0 cm/h for duration of 8 hou...

Q: Determine the maximum floor load that the simply supported interior stringer can carry based on the ...

Q: 3. Draw the internal force diagrams (and include all significant values) for the following system. 3...

Q: The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum an...

A: Determine the vertical displacement of the point where the force P =10 kips is applied.

Q: 3. From the figure shown below, the hydrostatic uplift varies linearly from one-half the hydrostatic...

A: Let density of concrete = 24KN/m3 [Note: first 3 part has been answered as per guideline]

Q: . A soil has a discharge velocity of 6× 10-7m/s and a void ratio of 0.5. its seepage velocity is 18x...

A: Given, Discharge Velocity: V = 6 * 10-7 m/s Void ratio: e = 0.5 To calculate, Seepage velocity. See...

Q: The maximum discharge of a river during floods is 200 cu.m./s. A weir is constructed across the rive...

A: A weir or low head dam is a barrier across the width of a river that alters the flow characteristics...

Q: PROBLEM 04: The fluid in the figure is water, with the surface 20m above the datum. The pipe is 15cm...

A: we will use bernoulli equation.

Q: The floor plan of a house in Boston, Massachusetts is given below. Indoor temperature = 72 °F. The g...

A: Given, Indoor temperature =72°F Garage temperature = Out door temperature

Q: Use Möhr's circle to solve the unknown values in the stress systems shown in figure 16.37. 80 MPa 70...

Q: A circular column of length 2 m has Euler's crippling load of 1.5 kN. If the diameter of column is r...

A: The given data is: Length of circular column=2 m Crippling load=1.5 kN Reduction in column diameter=...

Q: a. Calculate for the shear at column CB in kN using portal method. b. Calculate for the axial force ...

A: Portal Method: This method is proposed by Smith. This is an approximate method for lateral load anal...

Q: State the degree of indeterminacy of the structures(1,2,3,4,5...). If the structure is unstable inpu...

Q: Calculate for the degree of determinacy of the structures shown below and identify whether the struc...

A: Finding static indeterminacy

Q: Determine the horsepower for a 24,000 Ibs truck with a cross sectional area of 100ft and coefficient...

Q: Moist unit weight

A: The given question is related geotechnical engineering . In this question we are provided with value...

Q: Find the centroid of given composite figure. Set up the reference axis on the lower left corner. Rad...

A: To find centroid of the figure

Q: Problem 4: Determine the moment at B, then draw the moment diagram for the beam. Assume the supports...

Q: BA A 4 m 6 m

Q: Determine the member force LK(kN) in the figure shown. 2 m-2 m 2m 2 m 2m 2 m 2 m 2 m a 50 kN 50 kN 5...

A: We have to determine the value of member force LK in KN as shown in the figure as per the given data...

Q: A block , 1ft square and 9 inches deep floats on a stratified liquid composed of a 6in layer of wate...

A: Given: Block area = 1 ft² = 144 in² Depth of block = 9 in Depth of water layer = 6 in Block is 1 in...

Q: A four-lane freeway (two lanes in each direction) operates at capacity during the peak hour. It has ...

A: Solution- Refer to the "adjustment for lane width" chart. For a bro width of 11 feet, the lane width...

Q: SOLVE FOR THE REACTIONS AND DRAW THE SHEAR AND MOMENT DIAGRAMS OF THE FOLLOWING BEAMS PROVIDE A SOLU...

Q: ff = ? dg= ? d,- 2 kn.m I km tat Im 2m 2m Im, Jm

A: L = 7m

Q: Find the maximum shear stress if maximum principal stress is 30 MPa Minimum principal stress 20 Mpa

A: The given question is related with solid mechanics . In this question we are provided with value of ...

Q: Determine the magnitude of the reaction By (N) of the figure shown. 4 /2.000 N 400N/m 1.5 m B. 600 N...

Q: A prestressed T beam shown which is reinforced with a bonded tendon having an area Aps = 1580 mm?, f...

A: Given Aps= 1580 mm2 f`c= 34.5 Mpa

Q: The outer diameter of a pipe is drawn to circumscribe a square whose side is 3.75 cm long. If the in...

Q: Use Slope-Deflection Method to solve for the moment reaction at C in kN-m on the 250 mm x 350 mm bea...

Q: Calculate for the magnitude of the maximum bending moment on the beam shown, in kN-m. No need to inp...

Q: 78 Ibs 78 Ibs 104lbs 66 Ibs B 12 t 12 ft--- 12 ft-12 ft

Q: SOLVE FOR THE REACTIONS AND DRAW THE SHEAR AND MOMENT DIAGRAMS OF THE FOLLOWING BEAMS PROVIDE A SOLU...

Q: The Atterberg limits for the soil are LL = 105 and PL = 85. What is the PI?

A: The given question is related with geotechnical engineering . In this question we are provided with ...

Q: Estimate the lea<hing requirement when electrical <onductivity (EC) valve of a saturated extract of ...

Q: A kite at a height of 60 ft, is moving horizontally at a rate of 4ft per second away from a boy who ...

Q: starts from rest and accelerates uniformly over a time of 5.21 seconds for a distance of 110 m. Dete...

A: This question is related to the Engineering Mechanics.

Q: prestressed T beam shown which is reinforced with à dl. n, fc' = 34.5 MPa, fpu = 1862 MPa, and the e...

Q: The column critical bucking load depends on Column cross section size and shape Column material Colu...

A: To Choose :- the most correct options from the given ones

Q: Fig no.1 shows a room of internal dimension 4.0m x 2.5m. Calculate the quantities of the following i...

Q: The following are examples of Environmental Loads except; a. Wind load b. Seismic load c. Traffic lo...

A: Environmental loads are- Wind load Earthquake load/seismic load Snow load . According to...

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

i need the answer quickly

a) A simply supported beam AB, 6 m long is loaded as shown in Figure below
2 kN
5 kN
2 kN/m
1.5 m
D
E.
B.
1.5 m-
3 m
6 m
2: Draw shear force and bending momentdiagram for beam below
100KN m
M 1200 kN.m
A.
2 m
4 m
m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 I am solving only first question as per Bartleby guidelines

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel?
Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the bending moment 6.2 m to the right of point Aif W = 9.6 kN/m, T = 16.23 kNm, m = 8 m, and n = 3.9 m.
An indeterminate beam loaded a uniformly distributed load from A to B, from B to C, a linearly varying from 0 to 6 kN/m, is fixed at C, and a roller at point A and also in point B (where it settled 25 mm downwards here). The flexural rigidity is constant from A to C. Use E = 180 GPa, I = 1024 x 106 mm4 .Calculate the reactions and draw the shear and bending moment diagram for this beam using Slope Deflection Method.
For the beam and loading shown below (L = 2.4 m, E = 200 GPa, I = 1000 mm4 and w = 30 kN/m), find (a) TThe slope at point D.(b) The reaction force at end A
Determine the bending moment 2.25 m to the right of point A for the beam shown below if P = 1705 N, T = 3205 Nm, a = 0.95 m, b = 0.97 m, and c = 1.15 m. Round of the final answer (in N m) to four decimal places
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
Determine the reaction forces R1 and R2 and show the shear and bending moment diagram. Data: Point load (left-most) = 90.126 N RL1 (80mm to 160mm) = 65 N RL2 (160mm to 180mm) = 130 N RL3 (180mm to 260mm) = 65 N
The beam AB is subjected to the uniformly distributed load shown and to two unknown forces P and Q. Knowing that it has been experimentally determined that the bending moment is +6.10 kip ft at D and +5.50 kip ft at E, (a) determine P and Q, (b) draw the shear and bending-moment diagrams for the beam. 250 lb/ft C D E F Fig. P7.91
Determine the magnitude of F so that the resultant couple moment acting on the beam is 1.5 kN.m clockwise ?
For the beam shown in figure below, draw the shear and moment diagrams: 1- Due to applied loads (without support settlement). 2- Due to support settlement of 60 mm downward at support B (without loads). Take the stiffness El as 12000 kN.m?. 50 kN SKN/m
consider the moment-resisting frame. Use the portal method of analysis. Use P2 = 4 kips What is the shear force in the bottom beams (absolute value)? P1 = 2 kips What is the shear force in member EH (absolute value)? h = 11' What is the horizontal reaction at H (absolute value)? b = 25' What is the bending moment in the top beams (absolute value)? (please ignore black markings) What is the vertical reaction at I (tension positive)?
Determine the shear value when x = 5m (from the left) for the beam shown Where: P1 = 52kN; P2 = 42 kN; W1 = 12kN/m; W2 = 20kN/m