Find the centroid of given composite figure. Set up the reference axis on the lower left corner. Radius =

Q: is a structural system that is often used in buildings and mainly composed of beams and columns that...

A: (D) FRAMES is the correct answer. 

Q: Analyze the given structure using Virtual Work Method Determine the displacement at point B

A:

Q: For the beam shown in the figure below, draw the influence line for RC, and determine the maximum ab...

A:

Q: 29 The common tangent of a compound curve makes an angle of 14" and 20° with the tangent of the firs...

A:

Q: Design tw slab system marked by red color, known that live loal 3 KN /m2, tile = 23 KN/m3, Emortar :...

A:

Q: For the beam shown in the figure below, draw the influence line for RC, and determine the maximum ab...

A:

Q: 4. Stationing of old V. 5. Stationing of the new V.

A: The radius of the curve is expressed in terms of the degree. The radius of the curve for the 20m cha...

Q: 1.25 ft D = ? 1.25 ft 1.25 ft F. Fig. 6-1

A: Given: cube  Specific gravity of timber  To find: Submerged depth

Q: Water flows through a pipe at 144 L/s that changes gradually in diameter from 188 mm at point A to 4...

A:

Q: DISCUSS WHAT HAVE YOU LEARNED FROM THE  TOPIC  WOODS. YOU MAY WRITE IN ESSAY

A: Wood is an important construction material. Used widely in civil engineering works. It is very impor...

Q: Using the Slope Deflection Method (SDM). Solve for the following beam Given Values: E = 200,000 MPa ...

A:

Q: The A-36 steel rod has a diameter of 53 mm and is attached firmly to the rigid supports at A and B w...

A:

Q: For the beam shown in the figure below, draw the influence line for RC, and determine the maximum ab...

A:

Q: A kite at a height of 60 ft, is moving horizontally at a rate of 4ft per second away from a boy who ...

A:

Q: Two cables will lift an 18.500-meter-long prestressed pile weighing 3.806 kN/m. 1. Where should each...

A: The given  values are as follows. Size of Side of pile cross-section= 30 cm = 0.3 m  The Depth of pi...

Q: For a roof truss system of an industrial building, following data is given Span of truss = 6.0 m Spa...

A:

Q: The frame shown is supported in pivots at A & B. Each member weighs 50 lb per ft. Draw a FBD of each...

A:

Q: a. Compute the critical buckling stress (Fcr in MPa). b. Compute the nominal compressive strength of...

A:

Q: TOP VIEW

A: We can draw the top and Isometric view of the given drawing by using the following steps Draw the fr...

Q: An asphalt concrete mixture includes 94% aggregate by weight. The specific gravities of aggregate an...

A:

Q: How much is the maximum asphalt content range percentage (%) for a typical design by weight of total...

A: .The optimum asphalt content to many engineers is the an asphalt content corresponding to an air voi...

Q: is filled to a height of 9.84 in. The weigh that the mass of the empty tank is 5 kg, e r the followi...

A:

Q: A prestressed T beam shown which is reinforced with a bonded tendon having an area Aps = 1580 mm?, f...

A:

Q: t least 3 paragraphs, discuss the proper maintenance and usage of ladders. Discuss your idea on how...

A: A ladder is a collection of rungs or steps that can be upright or sloped. Rigid ladders, which are s...

Q: Use Möhr's circle to solve the unknown values in the stress systems shown in figure 16.37. 80 MPa 70...

A:

Q: 12 10 10-m 10-m 20 5.30 1.5 8.80 DETERMINE THE VALUES OF "a" AND "b"

A:

Q: 11. What are the principle of high-pressure improving drilling rate in petroleum drilling? 12. How t...

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since th...

Q: For the beam shown in the figure below, draw the influence line for RC, and determine the maximum ab...

A:

Q: For the built up section used in Enabling Assessment 1 and a framing configuration as shown below, c...

A:

Q: Find the nominal moment strength capacity of the beam. (kN.m)

A:

Q: A hollow circular shaft (outer diameter = 1.5 times the inner diameter) is subjected to a bending mo...

A:

Q: a. Compute the critical buckling stress (Fcr in MPа). b. Compute the nominal compressive strength of...

A: We have to determine the compute the critical buckling stress (Fcr in MPa) and compute the nominal c...

Q: Determine the shear and moments in the floor girder as a function of x. Assume the support at A is p...

A: ASKED: To write the shear and moment in the floor girder as function of x.

Q: Water at 60 degrees Fahrenheit have a density of 62.36 Ib/ft.^3 and dynamic viscosity of 7.536 x 10^...

A: To Find :- input pumping power required over 200 feet pipe length Given :-  Y = 62.36 lb/ft^3 Q = 0....

Q: THEORY OF STRUCTURES For the frame shown, sketch the shear and moment diagram. 19.35 kips internal ´...

A:

Q: Assignment 20 KN-m 40N 25 AN 4m Sm Sm 1.51 21

A:

Q: 58. For a sphere of radius 15 cm moving with a uniform velocity of 2 m/sec through a liquid of speci...

A:

Q: Determine the maximum floor load that the simply supported interior stringer can carry based on the ...

A: Given Data: The thickness of a slab is 75 mm. The span length is l=7 m. The web width is bw=300 mm. ...

Q: The civil engineering students calculate the overall strength of slab. they find that to its breakin...

A: When we have to calculate the overall strength of slab  then the minimum compressive strength for ga...

Q: Water spurts out horizontally from a 12mm round hole in the side of a timber penstock, the wall of w...

A: We have to determine the value of probable leakage in per 24 hours as per the given data in the ques...

Q: It is a structural system that is often used in buildings and mainly composed of beams and columns t...

A: Ans = Frames   Frames are structural system that is often used in buildings and mainly composed of b...

Q: A triangle has vertices at A( - 3, - 1 ), B( 6, 3 ), and C( 4, - 2). Find the equation of the altitu...

A:

Q: your answer. USE THREE MOMENT EQUATION. 30 kN/m

A:

Q: Instructions: Please provide complete solution for full credit and box final answer/s.   Problem: ...

A: Given : Percentage of aggregate by weight in mix, W1 = 94%Percentage of asphalt by weight in mix, W2...

Q: BA A 4 m 6 m

A:

Q: 3-m 150 mm CHB wal ick concrete footing. 3 kN/m2 and will carry ad of 20 kN per meter

A:

Q: Consider the beam shown in Figure. a. Write the equations for shear and moment. b. Evaluate the shea...

A:

Q: d loss from the reservoir to the gage is equal to twice the velocity cm pipe. p = 100 kPa

A:

Q: What is Rigging? What is its purpose in terms of aviation?

A:

Q: This is the part of the structural analysis and design process where the functional requirements of ...

A: Serviceability check In Serviceability check the functional requirement of structure are being estab...

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.