(a) A single phase, unity power factor load takes 60 A at 25 kV. Using a base voltage of 65 kV and base kilovolt amperes of 4425 kVA. Find the base current, base impedance,base power, per unit current and per unit voltage of the load (5 Marks )

(a) A single phase, unity power factor load takes 60 A at 25 kV. Using a base voltage of 65 kV and base kilovolt amperes of 4425 kVA. Find the base current, base impedance,base power, per unit current and per unit voltage of the load (5 Marks )

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14P: A single-phase source is applied to a two-terminal, passive circuit with equivalent impedance...

See similar textbooks

Related questions

Q: 2. A generating station has a maximum demand of 80 MW and a connected load of 150MW. If MWhr…

A: Given: Maximum demand = 80 MW Connected load = 150 MW MW hr generated in year = 400000

Q: A 13.8-kV, single-phase generator supplies power to a load through a step-up transformer, a…

Q: With neat diagrams explain how a three phase delta connection to be made with three windings and…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: The load's impedance is Zload = A 13.2-kV single-phase generator supplies power to a load through a…

A: Given: A 13.2-kV single-phase generator supplies power to a load through a transmission line. The…

Q: (a) the full load efficiency at unity power factor;

Q: Note: It is expected from student to develop impedance matrices of three phase power system. Develop…

A: From the given power system network Impedance matrix is develop as shown below

Q: QI A 3-phase, 80 MVA, 11-8 kV star-connected alternator with a solidly earthed neutral point has the…

Q: 1. Identify unity power factor points on V-curves and comment why you will not get unity power…

A: According to guidelines we need to solve only first question. According to the question we have…

Q: A balanced three-phase load of 1000 kW and 0.8 p.f. lagging is supplied by Vee-connected…

Q: 1. For each of the three single-phase transformers below, the phase pos voltage has been drawn on…

A: According to question: The phasor diagram is drawn by assuming that the turn ratio of each…

Q: Q.6 (a) Explain in detail the four-quadrant operation of chopper and how it is differed from dual…

A: Operation of four quadrant chopper four quadrant chopper consists of four semiconductor switches and…

Q: is a convenient way of representing a three-phase balanced system.

A: a three-phase system is represented using the simple diagram for simplicity.

Q: A 3-phase generator possesses a synchronous reactance of 60 and the excitation (induced) voltage Eo…

Q: b. Two 1-ph transformers 6000/400V, the first 200kVA and the other is 350kVA when performing the…

A: Given Parameters of single phase transformers.we need find the load shared by the two transformers.…

Q: (a) Describe the difference between displacement power factor and true power factor. (b) Briefly…

A: Difference between displacement power factor and true power factor. Displacement power factor only…

Q: A new industrial development has decided to'use two 350 kVA single-phase transformers to serve as an…

A: The explanation is as follows.

Q: Manufacturers usually specify the impedances of machines and transformers in O Percent O Per-unit O…

A: Need to Find correct option

Q: A step-down chopper, with voltage source 20V. If the duty cycle is 50 frequency is 0.1Hz, Find…

Q: 4. For the netwoYk Shown below sketch vo and determine Vor 2k2 12oyc'rms)

Q: The three phase power and line-line ratings of the below electric power system is given below Vm…

Q: A three-phase Y-connected alternator delivers a unity pf load at 230V. If the synchronous reactance…

A: The voltage regulation of alternator is given by V.Reg=(VNL-VFL)/VFL And to get in percentage…

Q: We use two identical transformers in experiment: (Parallel operation of two transformers) to achieve…

A: In order to achieve the condition of parallel operations of two transformers the given below…

Q: A balanced 3-phase load of 150 kW at 1000 V, 0.866lagging power factor is supplied from 2000 V, 3-…

A: Given:3-ϕ loadP=150kWV1=1000Vpf=0.866 lagging

Q: For step -down chopper circuit, source voltage Vs=220V, Chopping period T=2000micro second, on…

A: Step- down chopper is the DC input voltage. It is the static device the average output DC voltage of…

Q: For type-A chopper of. dc source voltoge = 230 V, load resistance = 102. Take a voltage drop of 2 V…

A: Given values are - VS=230VVD=2VDuty ratioD=0.4 Given that chopper is type-A so that it is step down…

Q: The three phase power and line-line ratings of the below electric power system is given below: Vm M…

Q: Two Alternators are operating in parallel supplying a common load of 4250KW at 85% power factor…

Q: A power station has to meet the following load demand: LOAD A 50kW Between 10 AM and 6 PM LOAD B…

A: The solution can be achieved as follows.

Q: Assume that a 2.5-kV 1-phase circuit feeds a load of 450 kW at a lagging load power factor load…

A: IL=215 a, PL=450Kw VL=2.5 kv(i) load apparent power sL=VLIL =2.5K×215 =537.5…

Q: For balanced Y - ∆ connected three-phase system, at 60 Hz during generator positive phase It…

Q: Note: It is expected from student to develop impedance matrices of three phase power system. Develop…

Q: 21. The total power drawn by two-impedance load in parallel is 15kW at 85% power factor lagging,…

A: The solution can be achieved as follows.

Q: Draw load curve of total power station and Find i- Load factor of total power station ii- Plant use…

Q: Evaluate the Merz-Price circulating-current scheme for an Alternator protection with appropriate…

A: Alternators are the important parts of electrical machines and power systems in terms of power…

Q: Draw the circuit diagram of power system layout with three phase CT and three phase PT.

A: Electrical Transformers can be used as Measuring devices when used in specific configuration. These…

Q: Please solve the problem and show the circuit diagram. Thank you. 3. A 5 MVA, 13.2 kV, 3-phase…

A: An alternator/Synchronous generator is a type of electrical machine that converts mechanical energy…

Q: A 1500-kW, 750, d.c., 6-phase synchronous converter is led by a bank of transformers connected in…

A: Given Data: Load = 1500 kW Edc = 750 V Primary line voltage = 23 kV Efficiency = 96% Pf = 0.92

Q: non-sinusoidal quasi-square wave voltage v(t) is applied to a nonlinear load, resulting in a…

Q: Explain the phase advancer method in power factor improvement?with a proper diagram.

A: According to the question we have to explain the phase advancer method in power factor improvement ?…

Q: Questions:- 1. Identify unity power factor points on V-curves and comment why you will not get unity…

A: 1) V bend is a plot of the stator current versus field current for various consistent burdens. The…

Q: 9- The impedance of two single phase transformers referred to secondary are (0.5+j3) and (0.6+j10)Q.…

Q: The interconnected system has the following advantages. It increases the service reliability and any…

A: A Brief About Interconnected System:- When different generating stations are connected together,…

Q: 6. A generating station has the following daily load cycle : Time (hours) 0-6 6-10 10-12 12-16 16-20…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: 1. Identify unity power factor points on V-curves and comment why you will not get unity power…

A: Since there are multiple questions uploaded within the same question, thus solving first question…

Q: Draw a complete equivalent circuit of one phase only of a synchronous generator. Then draw the…

Q: A balanced load consists of three coils with each coil having a resistance of 10 Ω and an induction…

Q: What is the alternators terminal phase voltage at shorted load condition? Explain and justify your…

A: Alternator: Alternator converts mechanical energy into electrical energy. Types of alternators:…

Q: The total instantaneous power absorbed by a three-phase motor (under balanced steady-state…

Q: A three-phase supply, with the line voltage 240 V rms positively phased, has an unbalanced…

Q: Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results: 0.C.…

Question

(a) A single phase, unity power factor load takes 60 A at 25 kV. Using a base voltage of 65 kV and base kilovolt amperes of 4425 kVA. Find the base current, base
impedance,base power, per unit current and per unit voltage of the load (5 Marks )

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The total instantaneous power absorbed by a three-phase motor (under balanced steady-state conditions) as well as a balanced three-phase impedance load is (a) A constant (b) A function of time
The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with a capacitive reactance XC=25. Calculate (a) the instantaneous power absorbed by the resistor, (b) the instantaneous power absorbed by the capacitor. (c) the real power absorbed by the resistor, (d) the reactive power delivered by the capacitor, and (e) the load power factor.
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the line-to-neutral voltages are always equal to zero. (a) False (b) True
A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True
A single-phase source is applied to a two-terminal, passive circuit with equivalent impedance Z=3.045, measured from the terminals. The source current is i(t)=22cos(t)kA. Determine the (a) instantaneous power, (b) real power, (c) reactive power delivered by the source, and (d) source power factor.
Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
While the instantaneous electric power delivered by a single-phase generator under balanced steady-state conditions is a function of time havi ng two components of a constant and a double-frequency sinusoid, the total instantaneous electric power delivered by a three-phase generator under balanced steady-state conditions is a constant. (a) True (b) False
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
Does an open connection permit balanced three-phase operation? - (a) Yes (b) No