(a) A steel cantilever beam with a 1-in-diameter round cross section and length of 10 in is loaded at the tip with a transverse force of 1000 lbf and an axial force of 5000 lbf, as shown in the figure. Study the significance of the transverse shear stress in combination with tension and bending by calculating magnitudes of the stresses. Explain and comment on the stresses and strains generated. 1000 lbf I in dia. Cross section at the wall 5000 lbf

(a) A steel cantilever beam with a 1-in-diameter round cross section and length of 10 in is loaded at the tip with a transverse force of 1000 lbf and an axial force of 5000 lbf, as shown in the figure. Study the significance of the transverse shear stress in combination with tension and bending by calculating magnitudes of the stresses. Explain and comment on the stresses and strains generated. 1000 lbf I in dia. Cross section at the wall 5000 lbf

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000
The 919-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 321 mm2. Find the location x (in mm) of P that can be safely applied to the bar if the stresses in AC and BD are limited to 112 MPa and 57 MPa, respectively. Express your answer in two decimal places.
P 130 mm 25 mm 25 mm P P 3. Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
The steel tie bar shown in Figure 2 is to be designed to carry a tensile force of magnitude P = 30 kips whenbolted between double brackets at A and B. the bar will be fabricated from 0.5* ? inches thick plate. Forthe grade of steel to be used, the maximum allowable stresses are: Normal stress = σn = 25 ksi, Bearingstress = σb = 55 ksi and Shearing stress = τ = 4.5* ? ksi. Solve for the values of (a) the diameter d of thebolt, (b) the dimension b at each end of the bar and (c) the dimension h of the bar.
A W18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 29 kips, w = 3.6 kips/ft, LAB = 6.4 ft, Lâc = 6.4 ft, and Lcp = 15.0 ft. Determine the magnitude of the maximum bending stress in the beam. A P LAB Answer: Omax = IH B LBC C W LCD D X
The working load P on the propped cantilever shown are each 150 kN. If the yield stress of mild steel is 300 MPa, determine the plastic section modulus in cubic millimeters, using a load factor of 1.75 against collapse. (express your response this way, x,xxX,XXX.X). Pu Pu 1.1 2m B A 2m 2m
il Engineering Dept. /Second Year "Strength of Materials" Home Works: A flat steel bar has axial loads (forces along the centroidal axis of the bar) applied at points A, B, C, and D, as shown in Fig. a. If the bar has a cross-sectional area of 3.00 in.², determine the normal stress in the bar (a) On a cross section 20 in. to the right of point A. (b) On a cross section 20 in. to the right of point B. (c) On a cross section 20 in. to the right of point C. Figure (a) 81 kip 30 in. 45 in. OA BOC 18 kip 54 kip 40 in. (a) Do Prof. Dr. Qais Fadhil 45 kip
A horizontal 50 kN load is applied on a 610UB125 Beam as shown in Figure 4. Determine the stresses at four corners A, B, C and D. Also, determine the angle that the neutral axis forms with the horizontal plane. The sectional properties are given in Table 1. 50k! 306 50 KN Table 2. Figure 4 (unit in mm) 306 mm bf d Y, A tr tw Section mm² mm mm mm mm 610UB125 16000 229 612 19.6 11.9 Sx lyo Sy (x106 (x10³ (x106 (x10³ mm²) mm³) mm²) mm³) 986 3680 39.3 536
A T section of a beam is fabricated from 2 - 12 mm x 150 mm steelplates and joined by welding as shown in Figure ST - 904. It carries a live loadof 6.5 kN/m extending half of its span. Neglect the weight 1. Compute the maximum compressive stress. ( bending stress incompression )2. Compute the maximum tensile stress. ( bending stress intension )3. Compute the maximum shear stress. 4. Compute the shear stress between the junction of web and flange. 5. Compute the maximum deflection. EI is constant.
A3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 KN. Poisson's Ratio = 0.25 and E = 200 000 MPa. Compute the total lateral deformation in mm (along the 300 mm side). Express your answers in 4 decimal places.
A cast iron beam is of I– section as shown in Figure (3). The beam is simply supported on a span of 5 m. If the tensile stress is not to exceed 20 N/mm2, find the safe uniformly load which the beam can carry. Find also the maximum compressive stress. -80 mm- 20 mm 169.34 mm 200 mm 20 mm N 90.66 mm 40 mm 160 mm Figure (3)
Find the value of uniform load (w) [ Kip/ft if the stresses in steel and aluminum are 22ksi and 15ksi respectively. w(kip/ft) ] 15ft 3in 3in 3in