The picture on the left depicts a beam loaded as shown. The red picture on the right is of the cross-section of the beam. a) Draw Force Diagram and Moment Diagram for the beam and loading shown by sectioning and developing force and moment equations for each section. b) Calculate max normal stress (ignore sign, just the max absolute value) 7,5cm 30KN/m 10KN 15cm B A semi 6m 2m circle

The picture on the left depicts a beam loaded as shown. The red picture on the right is of the cross-section of the beam. a) Draw Force Diagram and Moment Diagram for the beam and loading shown by sectioning and developing force and moment equations for each section. b) Calculate max normal stress (ignore sign, just the max absolute value) 7,5cm 30KN/m 10KN 15cm B A semi 6m 2m circle

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The system under the effect of torsion;a- Draw the torsional moment diagram.b- Determine the torsion angle CA (rotation angle) that will occur at point C.c- Determine the load shear stress.(G=80 000 MPa M1=5000Nm M2=4000Nm D1=120mm D2=90 D3=80 D4=60
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solutions. a. Vertical Reaction at B in kN.b. Moment Reaction at A in kN-m.c. Deflection at point C in mm.d. Deflection at midspan of AB in mm. Valuea = 3.7b = 26c = 29 Thank you very much!
4. An aerial copper wire (E =1x 10 5 N/mm ^2) 40 m long has cross sectional area of80 mm2 and weighs 0.6 N per meter run. If the wire is suspended vertically, calculatethe maximum weight which this wire can support at its lower end if the limiting valueof stress is 65 N/mm 2.a. 4627 Nb. 4281 NC. 4519 Nd. 5188 N
Draw the shear-force and bending-momentdiagrams for a cantilever beam AB acted upon bytwo different load cases.(a) A distributed load with linear variation andmaximum intensity q0 (see figure part a).(b) A distributed load with parabolic variation andmaximum intensity q0 (see figure part b).
Draw the shear force and bending moment diagram of the beam. Draw the distribution of normal stress and shear stress in the cross section of the beam at the B support. q=12t/m b=85mm h= 750mm t=30mm
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x150 mm section and E = 80 GPa. Show complete and organized solution. a. Vertical Reaction at B in kN. b.Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. Given: a- 7m b- 24kN/m C- 30kN
a simply supported beam is carrying a varying load and a uniform load as shown in the figure. If the beam properties are given below, what is the final stress at bottom of beam section at a distance 2.47m from the right support where the totall losses of the prestressing force is 24% mpa beam wid=217mm height= 480mm varying load= 9.67kn/m uniform load = 4.27 kn/m x = 3.32 y = 5.95 Prestressing force = 429kn eccentricity = 95mm
A structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries a tensile load of 29k;E=29 xx10^(3)ksi. a. Find the total elongation delta of the rod. b. What diameter d is necessary if the total delta is limited to 0.1 inch?
Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. Show complete and organized solution. a. Vertical Reaction at C in kN.b. Moment Reaction at C in kN-m.c. Deflection at point B in mm.d. Maximum deflection on the beam in m Valuea = 4.8b = 28c = 11 Thank you very much!
A circular beam carries a concentrated and a distributed load as shown in the figure. Determine the following unknowns if the modulus of elasticity is 90GPa and the maximum shear is 444.9kN. Let, P=170kN, a=2.5m, b=1m and c=3m ; If the deflection at the free end (leftmost part of the beam) is equal to -14.183444485219mm, Determine the radius of the cross-section of the circular beam. Determine the slope at the free end of the beam
The cantilever beam shown in Figure P15.15a is subjected to concentrated loads Px = 18kips and Py = 32 kips. The cross-sectional dimensions of the rectangular tube shape shown inFigure P15.15b are b = 8 in., d = 12 in., and t = 0.25 in. Point H is located at a distance of a = 24in. to the left of the concentrated loads. Calculate the principal stresses and maximum in-planeshear stress at point H for the following values of h:(a) h = 4.0 in.(b) h = 6.0 in.(c) h = 8.0 in.FIGURE P15.15a FIGURE P15.15bP15.43 A solid steel shaft with an outsidediameter of 1.5 in. is supported in flexiblebearings at A and C as shown in FigureP15.43/44. Two pulleys are keyed to the shaft atB and D. Pulley B has a diameter of D B = 14 in.and belt tensions of T 1 = 100 lb and T 2 = 220 lb.Pulley D has a diameter of D D = 7 in. and belttensions of T 3 = 60 lb and T 4 = 300 lb. Lengthdimensions of the shaft are x1 = 8 in., x2 = 4 in.,x3 = 3 in., and x4 = 6 in. Determine the normaland shear stresses at point K on…
Situation A: A beam is attached to a wire on the one end and is rested to an inclined plane on the other as shown below. Determine the following: 17. Force acting on the cable. Neglect friction. 18. Vertical and horizontal reaction at the inclined plane. Neglect friction. 19. Force acting on the cable. Coefficient of friction = 0.5 20. Vertical and horizontal reaction at the inclined plane. Coefficient of friction = 0.5