answer all subparts (a) A voltmeter with Permanent Magnet Moving Coil (PMMC) instrument of full-scaledeflection of 250 µA, and a coll resistance of 1.4 ko is shown Figure Q2 (a). Thevoltmeter range is 0-20 V.(1)Evaluate the value of the multipller resistance Re.(i)Calculate the value of shunt resistance needed to convert the voltmeter to anammeter capable of measuring a current of 20A.PMMCColresistanceMultiplierRresistanceR.Figure Q2 (a)

Answered: Image /qna-images/answer/e21fbdcc-02c7-4822-a806-1db7b5431079.jpg

(a) A voltmeter with Permanent Magnet Moving Coil (PMMC) instrument of full-scale deflection of 250 µA, and a coll resistance of 1.4 ko is shown Figure Q2 (a). The voltmeter range is 0-20 V. (1) Evaluate the value of the multipliler resistance Re. (i) Calculate the value of shunt resistance needed to convert the voltmeter to an ammeter capable of measuring a current of 20A. PMMC Col resistance Multiplier R resistance

(a) A voltmeter with Permanent Magnet Moving Coil (PMMC) instrument of full-scale deflection of 250 µA, and a coll resistance of 1.4 ko is shown Figure Q2 (a). The voltmeter range is 0-20 V. (1) Evaluate the value of the multipliler resistance Re. (i) Calculate the value of shunt resistance needed to convert the voltmeter to an ammeter capable of measuring a current of 20A. PMMC Col resistance Multiplier R resistance

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. A 2.0 Ω resistor is connected to a non-ideal source with internal resistance equal to 1.0 Ω and EMF equal to 15V. If the potential measured by the voltmeter across the resistor is 10V, find the rate of electrical energy dissipation in the battery.
Q3 / A: The Arton device is designed to configure an ammeter with ranges of 10 ampere, 5 ampere, and 1 ampere, given that the internal resistance of the circuit-breaker circuit is 50 ohms and the full current deviation is 1 milliampere.
A galvanometer has a full-scale deflection (FSD) current of 5 mA and an FSD voltage of 100 mV. In suitable circuits, it can be used as an ammeter or as a voltmeter. a) Explain, using circuit diagrams, the principles of these two circuits. b) Calculate the component values required to make it a voltmeter reading to 100 V, and an ammeter reading to 1 A.
Design a solar PV panel that can deliver 400W at 38V from a cross-sectional area of 12 square centimetres if the PV cell voltage is 0.7V the current density is 180A per metre square.
Q1) Conduct an evaluation on the practical applications of the concepts of electromagnetism and submit a written report which includes the following. a) Design a circuit which utilizes the concept of electromagnetism and submit a simulation circuit for the same (use simulation tool of your choice) b) Write down the selected values of the components used for example the values of resistors, transistor used, capacitors etc c) Obtain the output for the ciruit using any sinks like CRO, loud speakers etc. d) Discuss about the principles of electromagnetism used in the simulation I WANT QUESTION (D)
To protect an expensive circuit component from being delivered too muchpower, you decide to incorporate a fast-blowing fuse into the design.Knowing that the circuit component is connected to 12 V, its minimum powerconsumption is 12 W, and the maximum power it can safely dissipate is 100 W,which of the three available fuse ratings should you select: 1 A, 4 A, or 10 A?Explain your answer.
Design 7-step Voltmeter and 3-step Ammeter using galvanometer as integrated.
If the dark saturation current of a solar cell is 1.7X10-8 A/m2, the cell temperature is 27 oC, and the short-circuit current density is 250 A/m2, Vmax = 0.526 V, calculate the open-circuit voltage, Voc; current density at maximum power, Imax.
A circuit with a supply voltage of 2.5 V is being powered through a package. The packagehas a resistance of 100 m and a certain inductance L. The circuit requires at least 2.25 Vto function correctly. If this voltage is required in a time of 1ns, calculate the effectiveinductance L for the package.
A PMMC type voltmeter, having a full scale reading of 250 V and an internal resistance of 400 kilo ohms, is connect with a series resistance of 100 killo ohms. Calculate the sensitivity of the voltmeter.
If the same meter movement in no.4 is used to construct a multi range voltmeter whose ranges are 5 V, 10 V and 15 V, find the required resistances for the following configuration: a. Basic multi-range voltmeter b. Commercial multi-range voltmeter (given in no.4: A 3-V DC voltmeter is composed of a 500-Ω meter movement in series with a 2500-Ω series resistance.)
A battery with a terminal voltage of Vab = 9 V is connected to a circuit having three 10-ohm and one 5-ohm resistors all in series. Assuming that the battery has negligible internal resistance, calculate the potential drop across each resistor.