Q2: Design series ohmmeter using PMMC of 1002 internal resistance and 0.4ma full-scaledeflection current. The required half-scale deflection is equal to 9k0.juse a battery of 9v).Sketch the internal circuit diagram of the ohmmeter. Sketch also roughly the scale of thedesigned meter.

Series Ohmmeter:A simple Ohmmeter consists of a voltage source connected in series with a pair of…

Q2: Design series ohmmeter using PMMC of 1000 internal resistance and 0.4ma full-scale deflection current. The required half-scale deflection is equal to 9k.Juse a battery of 9v]. Sketch the internal circuit diagram of the ohmmeter. Sketch also roughly the scale of the designed meter.

Q2: Design series ohmmeter using PMMC of 1000 internal resistance and 0.4ma full-scale deflection current. The required half-scale deflection is equal to 9k.Juse a battery of 9v]. Sketch the internal circuit diagram of the ohmmeter. Sketch also roughly the scale of the designed meter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: a) An aluminum wire 7.5m long is connected in parallel with a copper wire 6m long. When a current of…

A: The resistance of a wire is calculated by the formula :- R=ρLAρ= resistivity of the materialL=…

Q: 3. (a) Define the unit of electrical current. (b) A battery has a terminal voltage of 24V when not…

A: Note :- As per guidelines we are supposed to answer only one question. So I request you to please…

Q: 3. If we were to connect a voltmeter directly to an ohmmeter, what would you expect to see the…

A: Voltmeter : voltmeter is device which used to measure voltage across resistors. It connected…

Q: ) With neat sketch explain the cross sectional view and I-V characteristics of the device which is…

Q: The length and dismeter of a copper wire are found to be 100 and 0.002 m, respectively. Consider…

Q: A battery with a terminal voltage of Vab = 9 V is connected to a circuit having three 10-ohm and one…

A: Given that A battery with a terminal voltage of Vab = 9 V is connected to a circuit having three…

Q: Q4/A shunt type ohmmeter uses a basic meter with a full scale current of 2mA and an internal…

Q: Q2/Design an Ayrton shunt by indirect method to provide an ammeter with current ranges 6A, 25A, and…

Q: current diminishes uniformly from an initial value of 40ma to zero in 0.8 sec, A constant source of…

Q: Define or explain the following terms: s) double-subscript notation (for voltage) t) passive…

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.

Q: At 298 K, the nominal Zener voltage is found to be equal to 10 V. Given that the value of the…

Q: Design a battery management system for the rechargeable battery to be used in solar system...Please…

A: According to the question we have to design the circuit diagram of the battery management system for…

Q: QI Design a multi range D.C. ammeter by using indirect method to give the following ranges 600 mA,…

A: DC Ammeter Internal resistance of PMMC meter = 30 ohm Full scale current 5mA Design a multi meter…

Q: QI\ An ohmmeter has a moving coil of resistance 24 2 with 4mA full scale deflection current. The…

Q: Chapter #3 Integrated Circuit Technologies HW #C Q. Use Table below to explain why the circuit of…

A: Given schematic diagram is shown below. In above diagram A,B and C are inputs . X and Y are…

Q: A PMMC instrument has internal resistance of 0.66 k2 and gives full scale deflection for 30 mA. The…

Q: What is the relationship between the voltage across the power and the current? (P = I V )

A: Voltage :- voltage is potential difference between two point in circuit. It is denoted by V.…

Q: Q3A sample of silicon 2volt is impressed of it has 0.25mm long and area (0.25x.3mm) the current…

A: It is given sample voltage V = 2 V. Length d = 0.25 mm Therefore, electric field is,…

Q: 2.2 The two zener diodes D, and D, in figure 2, have zener voltages of 9.1 V and 6.2 V respectively.…

A: In this question, Assume the forward bias voltage drop across each zener diode = 0.7V Let's input…

Q: Q4/ A shunt type ohmmeter uses a basic meter with a full scale current of 2mA and an internal…

A: Ohmmeter- An ohmmeter is an electrical device. It is used to measure resistance. its denoted by Ohm.…

Q: A sample of wire (1 mm in diameter by 1 m in diameter) length) of an aluminum alloy (containing 1.2%…

A: Given: A wire of aluminium alloy is placed in electrical circuit such that its parameters are

Q: In the figure R, = 6.32 N, R, = 19.0 N, and the ideal battery has emf ɛ = 12.4 V. (a) What is the…

A: Its combination of series and parallel combination of R1 and R2; Find the total current;…

Q: Does the C rating give the peak current of a battery? Say 10 Ah battery with a C-rating of 0.5C can…

Q: Design a multi-range voltmeter (250 volts) and 350 volts (note that the internal resistance of the…

A: Given data, V1 = 250 V. V2 = 350 V. Ig = 2 mA. Rg = 20 Ω.

Q: Estimate cell temperature, open-circuit voltage, and maximum power output for the KD230GX-LPB module…

A: As, Tcell=Tamp+NOCT-200.8.5 Tcell=30+47-200.8.1Tcell=64°C PV module performance data, under…

Q: 3) a) A wire sample (1 mm in diameter by 1 m in length) of an aluminum alloy (containing 1.2% Mn) is…

A: Voltage drop across the length= 432 mV. And current through it= 10 Amp. From ohm's law we know,…

Q: A PMMC instrument has internal resistance of 0.9 kN and gives full scale deflection for 53 mA. The…

A: Meter to work as voltmeter with multi range we have to add series resistor . We will use ohms law to…

Q: Q1: If PMMC meter have internal resistance of 2502 and half scale current of 5mA. Design an Ayrton…

A: PMMC METERRM=250IM(FULL SCALE CURRENT)=2×HALF SCALE CURRENTIM=2×5 = 10mA

Q: A voltmeter has a sensitivity of 800 Q/V and gives a value of 120 V on its 150 V scale when…

A: Based on the basic measurements devices

Q: A typical 12-V automobile battery, storing about 5 megajoules (MJ) of energy, is connected to a 4-A…

A: (a) The voltage delivered by the automobile battery E=12 V The current rating of the headlight…

Q: In solving a network, what rule must you observe when writing KCL equations? Why?

A: Given: Rules for KCL equations is shown as:

Q: Q1: If PMMC meter have internal resistance of 250n and half scale current of 5mA. Design an Ayrton…

Q: Q3. a)Design and calculate Series Type Ohmmeter uses a full scale current deflection, internal…

A: Note: Design parameters for ohmmeter are not given. We are designing for meter full scale deflection…

Q: A resistance of 2/(t + 20) Ω and inductance of 4 H are connected in series to a battery of unknown…

A: Apply KVL in the loop to get differential equation in terms of time t . Now differential equation is…

Q: Question-2: Determine Vout and Ip for the following three cases (draw the circuit for each case): A-…

A: As per company guidelines we can solve only first three sub parts kindly post another parts…

Q: 1.what are your comments on the future R&D directions for further improvement of NMH batteries? 2.…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: d'Arsonval movement with internal resistance of 1402 and Jeflection of 1.5 mA used to obtain the…

A: In this question we have to construct voltmeter multiplier.. A d'Arsonval basic meter movement is…

Q: For the circuit shown in the diagram below determine the emf of the battery and the potential drop…

A: To find the value of E, first, we need to find the total input current. Find the current in each…

Q: (i) Draw a circuit diagram of a DC analog ammeter with a current range of 1 A, 5 A and 10 A using an…

Q: .) A resistor has a resistance value of 20.0 ohms. a.) If it can handle a maximum of 5.00 watts of…

Q: Justify the reason, why the true value of a circuit is changed into reduced measured value because…

A: Solution:- An ideal voltmeter is assumed to have infinite resistance and due to which when it is…

Q: 3) Calculate the reşistance of a cross-sectional area A Od mmt) and resistivity of(50xl0- FR the…

Q: QI. Describe A- Dual-slope digital voltmeter. B- Electrical Standards.

A: A. DUAL SLOPE DIGITAL VOLTMETER The double incline incorporating type DVM coordinates the…

Q: 2- A battery supplies a current I to a resistor R with a potential difference E, the percentage…

Q: 6. a. The potential difference across the terminals of a battery is 8.5 V when there is a current of…

A: Kirchhoff's voltage law: It states that in any closed circuit or loop, the total voltage around the…

Q: The basic ohmmeter circuit shown is R1+Rm = 15KQ2, battery %3D voltage 1.5 V. If the meter has a…

Q: B! A shunt type ohmmeter uses a basic meter with a full scale current of 2mA and an internal…

Q: Q5/A- Design a series- type ohmmeter, consist of movement requires 0.5mA for full scale deflection…

A: Given: Full scale deflection current, IFSD=0.5 mAInternal resistance, Rm=50ΩVoltage, E=V=3VRh=3000Ω…

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

Q2: Design series ohmmeter using PMMC of 1002 internal resistance and 0.4ma full-scale
deflection current. The required half-scale deflection is equal to 9k0.juse a battery of 9v).
Sketch the internal circuit diagram of the ohmmeter. Sketch also roughly the scale of the
designed meter.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2: Design series ohmmeter using PMMC of 100Ω internal resistance and 0.4ma full-scale deflection current. The required half-scale deflection is equal to 9kΩ.[use a battery of 9v]. Sketch the internal circuit diagram of the ohmmeter. Sketch also roughly the scale of the designed meter.
1. A PMMC instrument has internal resistance of 1.7kΩ andgives full scale deflection for 50μA. Calculate the required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage ranges of 10V, 50V and 100V.
Five years ago, when the relevant cost index was 120, a nuclear centrifuge cost $40,000. The centrifuge had a capacity of separating 1500 gallons of ionized solution per hour. Today, the boss wants to build a centrifuge with capacity of 4500 gallons per hour, but the cost index now is 300. Assuming a power-sizing exponent of 0.75, determine the approximate cost in today's dollars of the new, larger reactor
The value of the multiplier resistance for a dc voltmeter, having 50 V range with 5 kohm/V sensitivity, employing a 200 micro.amp meter movement having internal resistance is 100 ohm, is given by
Define three clockwise mesh current from the circuit and employ the supermesh technique to obtain a numerical value for each??
Trying to solve this MOSFET exercise but not sure how.(Given Answer- R1 = 422 kohm R2 = 248 KOHM RD = 2.84 kohm, not sure if theres any error)
A specification sheet of a smart meter states that its rated current is 100 A and power dissipation is 3 W. It employs a current-sensing resistor of 200 μ. When the load current is at the rated value of the meter, calculate the power dissipation in all the other components of the meter.
S3) Calculate the current IB, IC and voltage VCE in the circuit in the figure and examine whether it is conduction or not? (VBE=0,7V , β=80)
Discuss solar energy and it's advantages . How solar energy can be converted into other forms of energy
Suppose a 8-V battery has an internal resistance of 0.3 ohm. What is the current that flows through the battery, if the battery terminals are momentarily shorted together? What is the terminal voltage if the battery delivers 0.25 amps to a circuit?
Explain (in your own words) what is meant by the terms, effective current andeffective voltage.
A 30-Wp SHS has a charging current of 1.7A at 1000 W/m2 irradiance. When the irradiance is decreased to 800W/m?, how much charging current is expected?