A A. The weight of the crate B. The internal force in rod AC 60° -60° C For the figure above, rods AC and BC are used to support the crate at point C. If the crate has a mass of 350 kilograms, determine the following: B C. The required diameter of rod BC if the normal stress of the rod cannot exceed 2300 kPa. Round to two decimal places. D. If pin A is in single shear, and the shear stress of the bolt should not exceed 60 MPa, what is the required diameter of the bolt in pin A?

A A. The weight of the crate B. The internal force in rod AC 60° -60° C For the figure above, rods AC and BC are used to support the crate at point C. If the crate has a mass of 350 kilograms, determine the following: B C. The required diameter of rod BC if the normal stress of the rod cannot exceed 2300 kPa. Round to two decimal places. D. If pin A is in single shear, and the shear stress of the bolt should not exceed 60 MPa, what is the required diameter of the bolt in pin A?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
Determine the shear stress (in Mpa) in the 20.75-mm-diameter pin at A that support the beam if P = 28.96 kN, a = 2.12 m, and b = 5.72 m. Round off the final answer to three decimal places.
The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the vertical displacement of point C if the stress in the steel rod is limited to 29.16 ksi, X = 2.87 ft, and Y = 4.08 ft. Neglect the weights of the members.
The hinge support at A and steel rod at B support the horizontal rigid bar (neglect the weight of the bar) as shown. Determine the maximum vertical force P that can be applied at the end of the bar at C if the allowable stress in the steel rod is 35 ksi and the vertical displacement at C is limited to 0.21in.Use 2 decimal places.
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
For the shaft shown, a. Determine the maximum stress on the shaft and the maximum angle of twist of end D relative to end A. b. If the stress in every section must not exceed 25 MPa, what should be the uniform diameter of the shaft? dAB = 100mm, dbc = 80mm, dcd = 50mm G for the shaft is 80GPa. Consider clockwise torques as negative.
Determine the maximum absolute bending strain in the following tubular shaft if di = 160 mm and do = 200 mm. (E = 154 GPa)
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15,000 ksi] rods, and a solid steel [E = 30,000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.500 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.360 in. If all bars are unstressed before the load P is applied, determine the normal force in steel rod (2) after a load of P = 36 kips is applied.
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , and L1 = 6 m , and supports two lateral loads P1 = 10 kN and P2 = 12 kN . The area of column AE is 40 cm2 and the area of column BF is 80 cm2 . a) Use the cantilever method to determine the axial force at G. Gy = ? b) What is the horizontal reaction from the ground on the base of the column at A? Let a positive reaction be pointing to the left. Ax = ? c) What is the horizontal reaction from the ground on the base of the column at B? Let a positive reaction be pointing to the left. Bx = ?