The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the vertical displacement of point C if the stress in the steel rod is limited to 29.16 ksi, X = 2.87 ft, and Y = 4.08 ft. Neglect the weights of the members. Round off the final answer to four decimal places. ... L = 4 ft |A = 0.5 in.2 E = 29 ×10° psi B A

The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the vertical displacement of point C if the stress in the steel rod is limited to 29.16 ksi, X = 2.87 ft, and Y = 4.08 ft. Neglect the weights of the members. Round off the final answer to four decimal places. ... L = 4 ft |A = 0.5 in.2 E = 29 ×10° psi B A

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KN Solve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters. You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
If FA = 7 kN and FB = 5 kN, represent the force system acting on the corbels by a resultant force, and specify its location on the x–y plane.
Calculate the forces and stresses in members AB, DF, and BD. Given: d = 0.05 m
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
The normal and shear stresses on a plane are 120 psi (C) and 25 psi respectively. On an orthogonal plane, the respective stresses are 40 psi (C) and 25 psi. Draw Mohr's circle and determine the angle between minor principal plane makes with the 120 psi stresses.
QUESTION 2) A bending moment of M=4 kNm, tan alpha (α)=0.577, acts on the section in the figure. Unbiased Determine the position of the axis and draw the stress distribution in the section
For the frame in Figure P8.33, compute the horizontal and vertical displacements at joint B. Given: I = 150 in.4 , E = 29,000 kips/in.2 . Consider only the flex- ural deformations.
If the beam is subjected to a bending moment of M = 5 kN # m, determine the bending stress developed at point A and sketch the result on a differential element at this point.
Determine the horizontal displacement of joint B. You can assume that joint B displaces to the left. The length of the truss AB, BC, AC, L, is 1,760 mm. The applied force at point C, P, is 60 kN. The diameter of the trusses, D, is 16 mm. The elastic modulus of the three trusses , E, is 200 GPa.
The hinge support at A and steel rod at B support the horizontal rigid bar (neglect the weight of the bar) as shown. Determine the maximum vertical force P that can be applied at the end of the bar at C if the allowable stress in the steel rod is 35 ksi and the vertical displacement at C is limited to 0.21in.Use 2 decimal places.