A B C a b.

Q: 3. Determine the components of the resultant force and the magnitude of the resultant. x = 20 m, y…

A: A20,15,0B-6,4,0C16,-18,0D0,0,24Postion vectors are rDA=20i+15j-24krDB=-6i+4j-24krDC=16i-18j-24k

Q: For the overhanging beam loaded as shown, determine the maximum values of flexural stress and…

A: For the equilibrium of the beam (i) ∑MA = 0 (cw +ve, ccw -ve) (720 x 8 x 4) + [ 0.5 x 720 x 2.25 x…

Q: For the overhanging beam loaded as shown, determine the maximum values of flexural stress and…

A:

Q: Find the support reactions and joint force of the construction, shown on the figure, if: P=12 kN, q…

A: Finding out support reactions.

Q: 09 a) Calculate the vertical and horizontal reactions in the frame below (Figure 3), assume a 7…

A: Taking Moment at E point ∑ME=0VA×11+1.4×4×1+42=4.2+3.2×112×114+5.2cos35×2 11VA+16.8=111.925+8.52…

Q: 2. A sign with dimensions of 2.0 m x 1.2 m is supported by a hollow circular pole having an outer…

A:

Q: he pressure distribution over the base of a concrete (S =2.4) dam varies linearly, as shown in…

A: Pressure distribution over Base of concrete varies linearly (S = 2.4) It has been asked in the…

Q: 2. Determine the magnitude of the resultant of the two forces shown. F13 kN 30 5=7 kN

A:

Q: The overhanging beam supports the loads as shown in the figure. Determine the maximum shear stress…

A:

Q: Identify the loading diagram for the given shear force diagram. 9.60 kN 5.6 kN -4.40 kN 3 m 2 m 5 m

A:

Q: look for and show complete solution: a. Reactions b. Shear and Moment Diagram c. Maximum Moment d.…

A: For the beam shown below, the reactions, SFD, BMD, maximum moment and equations have to be…

Q: A 1.10-in.-diameter solid shaft is subjected to an axial force of P = 3300 lb, a horizontal shear…

A: Given: The diameter of the shaft is 1.1 in. The axial force P is 3300 lb. The horizontal shear force…

Q: nd force P =500 KN. Compute the moment of Force F@ points E. * E A P C F D

A:

Q: Determine the values of a and 0 so that the forces shown will be in equilibrium. A=30 kN, B=40 kN,…

A:

Q: 3. Treating the force at B as an upward load B, determine its value using superposition. E= 200 GPa…

A:

Q: Calculate the components of the forces at B and C. A P B D Given: P = 20 kN a = 1.1 m b = 1.3 m c=…

A:

Q: Determine the shear force (V) in kN at point D for the beam as loaded in Figure 3.2a10. Givena =…

A: Given:- a beam as shown below

Q: Determine the magnitude of the vertical reaction force at B. Assume a = 4.3 ft, b = 8.6 ft, c= 17.2…

A:

Q: Replace the 4.4-kN force by an equivalent force-couple system at (a) point O and (b) point B. Give…

A:

Q: Determine the shear stress in point D in beam shown in Figure 5. 150 kN 2 m 20 kN/m b 75 mm D. h A B…

A: Solution:-

Q: For the dam shown in the figure , assuming the width of the dam (into the page) is 1 ft. Determine…

A:

Q: For the overhanging beam loaded as shown, determine the maximum values of flexural stress and…

A: Given A beam and it's cross section  Required  Maximum flexural stress and shear stress

Q: For the section shown, if d = 200 mm, horizontal shear force = 100 kN to the right and torque = 15…

A: To find out the total shear stress at B.

Q: Problem 3 A force system is shown below. 280 kN 40% 30° 150 kN a. Determine the x-component of the…

A:

Q: STRESSES 1. Compute the maximum shear stress and maximum flexural stress of the beam shown in the…

A:

Q: B A b Calculate the support and joint reactions, draw the free-body diagram! Input data: P = 10.00…

A:

Q: If the beam is subjected to a bending moment of M = 27 kN. m , determine the maximum bending stress…

A: The given data is shown below:

Q: The vertical shear force acting on the cross section shown is 1000+2(37)lb. Determine the shear…

A: Given data V=1000+237   =1074lbThe sides are given in the figure above

Q: b) Figure Q1 (b) shows a log with 1.2 m of diameter and 4 m of width is located between the two…

A: step 1-

Q: Q.2) Determine the magnitudes of forces P and Q acting on the block so that the resultant of all…

A:

Q: Determine the magnitude of the vertical reaction force at B. Assume a = 4.3 ft, b = 8.6 ft, c = 17.2…

A:

Q: beam is subjected to a torque of 1 kNm at its free end, plot the angle of twist of the beam at 500…

A: At free end,b = Width =  50 mmd = Depth = 150 mmT = Torque = 1 KN.mG = Modulus of rigidity = 25000…

Q: S. A rectangular beam 10 cm wide, is subjected to a maximum shear force of 50,000 N, the…

A:

Q: 30 kN 3 m 20 kN 3 m 10 kN 3 m 3.6 m 5 m

A:

Q: The three forces shown are equivalent to a 50-kN upward force at A and a 200-kN.m counterclockwise…

A:

Q: P=2,900 kN (parabolic) P=1,100 kN 0.05 0.45 m. 0.30 0.15 0.45 m. A' 0.075 EO E 0.45 m. 6.0 m. 6.0 m.…

A: Given force in Parabolic tendon, P=2900KN                   force in Linear tendon, P=1100KN,…

Q: A 1.10-in-diameter solid shaft is subjected to an axial force of P = 1800 lb, a horizontal shear…

A:

Q: Calculate the horizontal shear stress TA at point A,

A: Solution: Shape Width b (mm) Height h (mm) Area Ai (mm2) yi (from bottom) (mm) yiAi (mm3) Left…

Q: 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using…

A:

Q: From the figure shown, 10' kN H 3 m 20 kN 5 m 3 m 5 m В a. Determine the axial force of girder GH.…

A: Portal method will be used for this given question. Assumptions in portal method :- A) point of…

Q: From the gerber beam below, calculate the support reactions and draw diagrams of soliciting stresses…

A:

Q: If the 60 mm diameter shaft is subjected to an axial force of 10 kN, determine the average shear…

A:

Q: Н.W 1. Calculate the angle of twist (0) for the bar using G = 85 x 10 N/mm? OG 100 mm 15 kN. m 2. If…

A:

Q: Using the Clayperon Method, Determine: 1. Support Reaction 2. Internal forces (Shear Force, Normal…

A: A structure is a body or a set of interconnected elements that supports a load. Buildings, bridges,…

Q: 27 kN 4 m 49 kN D E F 5 m H. K 6 m 4 m 8 m Determine the following: A Shear force for column DH. (

A:

Q: Given w=823 kN/m, find: (1) reaction forces at support A and B. (2) the internal forces 4m to the…

A: A UDL of 823 kN/m for 6 m.  A point load of 100 kN acting downward. To determine support reactions…

Q: The uniform sign has a weight of 7.5 kN and is supported by the pipe AB, which has an inner radius…

A:

Q: 2. A sign with dimensions of 2.0 m x 1.2 m is supported by a hollow circular pole having an outer…

A:

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.