A B D When the CD temperature rises by 60 ° C, calculate the internal force of the column with a diameter of 75mm. At the beginning, there is no gap between the column and the beam, and the beam is in light contact. The column is made of A-36 steel, and the moment of inertia of the beam is i=255 [10^6) mm^4 C 3 m

A B D When the CD temperature rises by 60 ° C, calculate the internal force of the column with a diameter of 75mm. At the beginning, there is no gap between the column and the beam, and the beam is in light contact. The column is made of A-36 steel, and the moment of inertia of the beam is i=255 [10^6) mm^4 C 3 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.12P: A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the...

See similar textbooks

Similar questions

The fr a me A BCD shown in the heure is squeezed by two collinear forces P acting at points A and D. What is the decrease ê in the distance between points A and D when the loads P are applied? (The flexural rigidity EI is constant throughout the frame,) Note: Disregard the effects of axial deformations and consider only the effects of bending due to the loads P.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E = 10.6 × 106 ksi. The defied ion at the top is limited to 2.0 in.
-7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the weight density of steel.
A heavy flywheel rotating at n revolutions per minute is rigidly attached to the end of a shaft of diameter d (see figure). If the bearing at A suddenly freezes, what will be the maximum angle of twist <£of the shaft? What is the corresponding maximum shear stress in the shaft? (Let L = length of the shaft, G = shear modulus of elasticity, and / = mass moment of inertia of the flywheel about the axis of the shaft. Also, disregard friction in the bearings at Sand Cand disregard the mass of the shaft.) Hint: Equate the kinetic energy of the rotating flywheel to the strain energy of the shaft.
Thank u Find the Moment of Inertia (based on Carbon, change the E-Glass to Carbon), I, for the section shown. Calculate by using the Face Sheets only, do not include the foam. Given: E-Glass, E = 3,000,000 psi; Carbon, E = 9,000,000 psi; Cross-Section of the sheet; w (width) = 24” T1 = 0.6”; T2 = 10”; T3 = 1.4” NA = ________ in Moment of Inertia, I =______________________ in4
A 37.5-mm-diameter rod 6 mlong elongates 12 mm under a load 236 KN. Thediameter of the rod decreases 0.025 mm during theloading. Determine the following properties of thematerial: (a) Poisson’s ratio.(b) Young’s modulus(c) The modulus of rigidity.
Determine the equivalent stiffness of a cantilever beam which is loaded transversely on its end and has a length in 5000 mm and an annular cross section with inner and outer diameters of 25 mm and 22 mm, respectively. The modulus of elasticity of the beam is 72x109 N/m2. Use moment of inertia I=π(D4o−D4i)/64 and spring constant is (k= 500 N/m). Answer must be in three decimal places.
A vertical shaft 25 mm diameter and 0.75 m long is mounted in long bearings and carries a pulleyof mass 10 kg midway between the bearings. The centre of pulley is 0.5 mm from the axis of theshaft. Find (a) the whirling speed, and (b) the bending stress in the shaft, when it is rotating at 1700r.p.m. Neglect the mass of the shaft and E = 200 GN/m2.
Find the Young’s modulus (Y) of the steel rod of 1 m long and a cross sectional area of 0.05 cm2, elongates 2% when supported by a 120 kg load, hung from the other end.
Find the amount of depression in mm at the midpoint of the bar AB.Mo = 1kNm, L = 1m, E = 200 GPa, I=1x106 mm4
Find the amount of depression in mm at the midpoint of the bar AB. Mo= 1kNm, L = 1m, E = 200 GPa, I=1x106mm4