A balanced, star connected three-phase system is directly connected to an unbalanced load, with a solid neutral connection. The line-to-neutral voltage Van on the load side and per phase load impedances (i.e., Za, Zb and Zc) are as below: ?an = 240∠0 ? ?? = 10 + 3? Ω ?? = 16 + 3? Ω ?? = 10 + 3?Ω Draw the circuit diagram and calculate the sequence currents and neutral curren

A balanced, star connected three-phase system is directly connected to an unbalanced load, with a solid neutral connection. The line-to-neutral voltage Van on the load side and per phase load impedances (i.e., Za, Zb and Zc) are as below: ?an = 240∠0 ? ?? = 10 + 3? Ω ?? = 16 + 3? Ω ?? = 10 + 3?Ω Draw the circuit diagram and calculate the sequence currents and neutral curren

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.24MCQ: It is stated that (i) balanced three-phase circuits can be solved in per unit on a per-phase basis...

See similar textbooks

Similar questions

A three-phase overhead line has a load of 30MW, the line voltage is 33kV and power factor is 0.85 lagging. The receiving end has a synchronous compensator, 33kV is maintained at both ends of the line. (i)Calculate the MVAr of the compensator given that the line resistance is 6.5Ω per phase and inductance reactance is 39Ωper phase. (ii)Repeat your calculation using the short-circuit current at node method. Compare and explain the difference between the results.
1. A 69-kV, three-phase short transmission line is 16 km long. The line has a per phase series impedance of 0.125+j0.4375 Ω per km. Determine the sending end voltage, voltage regulation, the sending end power, and the transmission efficiency when the line delivers (a) 70 MVA, 0.8 lagging power factor at 64 kV. (b) 120 MW, unity power factor at 64 kV. Use lineperf program to verify your results. 2. A three-phase, 765-kV, 60-Hz transposed line is composed of four ACSR, l,431,000-cmil, 45/7 Bobolink conductors per phase with flat horizontal spacing of 14 m. The conductors have a diameter of 3.625 cm and a GMR of 1.439 cm. The bundle spacing is 45 cm. The line is 400 km long, and for the purpose of this problem, a lossless line is assumed. (a) Determine the transmission line surge impedance Zc, phase constant ß, Wavelength, the surge impedance loading SIL, and the ABCD constant. b) The line delivers 2000 MVA at 0.8 lagging power factor at 735 kV. Determine the sending end quantities and…
I need all steps answer A 3-phase overhead transmission line delivers a load of 80 MW at 0.8 pf legging 220 KV between the lines. Its total series impedance per phase and shunt admittance per phase is 200∠80° ohms and 0.0013 ∠90° mhos per phase respectively. Using nominal T method determine (i)A,B,C,D constants of the line (ii) Sending end voltage (iii) Sending end current (iv) Sending end power factor (v) Transmission efficiency of the line.
single circuit three-phase line, 60 Hz, 18 km has a total resistance and inductive reactance of 4.242 ohm and7.451 ohm per phase respectively. The line delivers 2500 kW to a balanced load at 11 kV. (1) determine the sending-end voltage when the power factor is (i) 80% lagging, (i) unity, and (ii) 90 % leading, (2) draw the phasor diagrams of the line at the above (3) determine the voltage regulation of the line at the above power factors.
A balanced, positive-sequence, Y-connected voltage source with Eab = 480∠0o volts is applied to abalanced-∆ load with Z∆ = 30 ∠40o Ω. The line impedance between the source and load is ZL = 1 ∠850 Ω.for each phase. Calculate the line currents, the ∆ -load currents, and the voltages at the load terminals.Recall that ZY = Z∆/3
A 400V three-phase, four wire system has the following loads connected: Phase 3: load impedance Z3 = 15 – j20 Ω Draw the circuit diagram and determine: The line and phase voltages for phase 3 (including phase angles) The line and phase currents for for phase 3 (including phase angles) The neutral current (including phase angle)
6. An abc-sequence, three-phase, 4-wire, 380-V supply is connected to an unbalanced load having phase impedances of: Za = 8 + j6 ohms, Zb = 8 - j6 ohms and Zc = 5 ohms. Impedance of the neutral wire is 0.5 + j1 ohms. Line impedance is 1+ j2 ohms per phase. Find the value of the neutral current in polar form.
A 220 kV, 50 Hz, three-phase transmission line is 60 km long. The resistance per phase is 0.15 ohms/km and the inductance per phase is 1.3 mH per km and the shunt capacitance is negligible. Use the short line model to determine; i) the voltage and power at the sending end ii) voltage regulation and efficiency when the line is supplying a three-phase load of 350 MVA, 220 kV at a power factor of 0.85 lagging.
Q1: The parameters of a three-phase line 200 km long are resistance/km-0.15 0, inductivekm -0.5 and capacitive susceptancekm-2x 10° U. The transmission line is delivering 50 MVA at 132 kV with power factor 0.85 lagging. Use nominal T method to determine; 1) sending end voltage 2) sending end current 3) sending end power factor 4) transmission efficiency and 5) voltage (4 points) regulation
hallo A 69-kV, three-phase short transmission line is 16 km long. The line has a per phase series impedance of 0.125 + j0.4375 ohm per km. Determine the sending end voltage, voltage regulation, the sending end power, and the transmission efficiency when the line delivers 70 MVA, 0.8 lagging power factor at 64 kV. 120 MW, unity power factor at 64 kV. Use lineperf program to verify your results.
A single phase transmission line is delivering 470 kVA load at 14 kV. Its resistance is 4 Ω and inductive reactance is 8 Ω. If the load power factor is 0.9 lagging. Determine the 1Current through the line: 2Sending end voltage: 3Sending end power factor: 4Regulation of transmission line: 5Efficiency of transmission line:
This wind farm needs a 250 km connection laid to Sommerville. The choice is either a 3 phase system or a bipolar dc system at 400 kV and ±400 kV at the receiving end respectively. (i) The 3-phase system has resistive losses per phase of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (ii) The bipolar dc system has resistive losses of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (iii) Calculate the efficiencies of the two systems. (iv) Comment on which system you would choose to use and why.