A balloon is being inflated to its full extent by heating the air inside it 6. 6. In the final stages of this process, the volume of the balloon changes from 4.00x10 L to 4.50x10 L by the addition of 1.3x10 Jof energy as heat Assuming that the balloon expands against a constant pressure of 1.0 atm, calculate AE for the process To convert between L· atm and J, use 1L· atm = 101.3 J

A balloon is being inflated to its full extent by heating the air inside it 6. 6. In the final stages of this process, the volume of the balloon changes from 4.00x10 L to 4.50x10 L by the addition of 1.3x10 Jof energy as heat Assuming that the balloon expands against a constant pressure of 1.0 atm, calculate AE for the process To convert between L· atm and J, use 1L· atm = 101.3 J

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.39P: The tip of a soldering iron consists of a 0.6-cm- diameter copper rod, 7.6 cm long. If the tip must...

See similar textbooks

Similar questions

A piston-cylinder assembly initially contains 100 kPa of pressure and 2 Liter of air at 25 ° C. Then the air is compressed to 620 kPa pressure and 160 ° C. The useful work done for compression is 1.22 kJ. Assuming that the ambient pressure and temperature are 100 kPave 25 ° C, respectively, a) Calculate the availability of air in the initial and final states, b) the minimum work required for the compression process, c) the second-law efficiency of the process change.
An insulated evacuated tank having a volume of 50 ft3 is attached to a constant pressure line containing steam at 50 psia superheated by 10F. Steam is allowed to flow into the tank until the pressure has risen to 50 psia. Assuming the tank to be insulated and to have a negligible heat capacity, how many lbm of steam will enter the tank?
Calculate the amount of heat which enters or leaves 1kg of steam initially at 0.5MPa and250OC, when it undergoes the following processes: a. It is confined by a piston in a cylinder and is compressed to 1MPa and 300OCas the piston does 200 kJ of work on the steam.b. It passes in steady flow through a device and leaves at 1MPa and 300OCwhile, per kg of steam flowing through it, a shaft puts in 200 kJ of work. Nochanges in KE and PE.c. It flows into an evacuated rigid container from a large source which ismaintained at the initial condition of the steam. Then 200 kJ of shaft work istransferred to the steam, so that its final condition is 1MPa and 300OC.
1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. What is h1 in kJ/kg?
A piston-cylinder assembly initially has 100 kPa pressure and 2 Liter air at 25 ° C. The air is then compressed to 620 kPa pressure and 160 ° C. Useful work for compression is 1.22 kJ. Assuming that the ambient pressure and temperature are 100 kPa and 25 ° C respectively, a) Calculate the availability of air in the initial and final states, b) the minimum work required for the compression process, c) Calculate the second law efficiency of the state change.
A piston-cylinder assembly initially contains 100 kPa pressure and 2 liters of air at 25°C. Then the air is compressed to a pressure of 620 kPa and a temperature of 160 ° C. The useful work done for compression is 1.22 k). Considering that the ambient pressure and temperature are 100 kPa and 25°C respectively, a) Calculate the usability of air in the initial and final states., b) Calculate the minimum work required for the compression process. c) Calculate the second-law efficiency of the state change. (Please solve in detail and according to engineering rules. ) Thermodynamics
Draw the PV and TS Diagram of this problem. Steam at 5 MPa and 400 °C expands polytropically to 1.0 MPa according to pV 1.3=C.Determine the work of nonflow and steady flow, the heat transferred, Δh, and Δs.
One mole of carbon dioxide is to be compressed adiabatically from 1 bar and 25⁰C to 10 bar. Because of irreversibilities and poor design of the compressor, the compressor work required is found to be 25 % greater than that in a well-designed (reversible) compressor. Compute the outlet temperature of the carbon dioxide and the work that must be supplied to the compressor for both the reversible and irreversible compressors. Assume carbon dioxide is an ideal gas with the constant-pressure heat capacity (in J/mol.K) given below. (Please write assumptions) ??(?) = 22.243 + 5.977 ∗ 10^-2∗ ? − 3.499 ∗ 10^-5∗ ?2 + 7.464 ∗ 10^-9∗ ?3
One mole of carbon dioxide is to be compressed adiabatically from 1 bar and 25⁰C to 10 bar. Because of irreversibilities and poor design of the compressor, the compressor work required is found to be 25 % greater than that in a well-designed (reversible) compressor. Compute the outlet temperature of the carbon dioxide and the work that must be supplied to the compressor for both the reversible and irreversible compressors. Assume carbon dioxide is an ideal gas with the constant-pressure heat capacity (in J/mol.K) given below. (Please write assumptions) (Hint: You can either use Matlab or Octave to solve for T numerically or you can use a trial-error procedure.)
Box the final answer. Write legibly. Steam flows into a turbine at a rate of 3.5 kg/s and ¾ MW of heat are lost from the turbine. Ignoring elevation and kinetic energy effects, calculate the power output from the turbine in KW? Steam pressure entering the turbine is 62 Bar at 440ºC and leaves at 74 Kpa.
Superheated steam at a pressure of 40 bar and a temperature of 500 0C enters a steam turbine. The exhaust steam leaves the turbine at a pressure of 0.2 bar with a dryness fraction of 0.85. If the steam flow rate is 150,000 kg/hr and the rate of heat loss from the turbine is 800 kW, find the power developed by the turbine. Also determine the volume flow rate of steam at inlet to and exit from the turbine. (Hint: 1 bar = 100 kPa , dryness fraction = quality of steam)
Steam at 5 MPa and 400 °C expands polytropically to 1.0 MPa according to pV 1.3=C.Determine the work of nonflow and steady flow, the heat transferred, Δh, and Δs. Draw PV and TS diagram