Sketch these thermodynamic process on a PV diagram Problem 1. At point A in a Carnotcycle, 2.34 mol of a monatomic idealgas has a pressure of 1400 kPa, avolume of 10.O L, and a temperatureof 720 K. It expands isothermally topoint B, and then expandsadiabatically to point C where itsvolume is 24.0 L. An isothermalcompression brings it to point D,where its volume is 15.0 L. Anadiabatic process returns the gas topoint A.

For a Carnot cycle Process A-B is an isothermal expansion Process B-C is an adiabatic expansion…

Answered: Sketch these thermodynamic process on a…

Engineering

Mechanical Engineering

Sketch these thermodynamic process on a PV diagram

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Sketch the T-S Diagram and label each region.

Q: Steam at 2.0 kPa is saturated at 17.5C. In what state will the steam be at 40C if the pressure is…

Q: Find these set of values in the steam table: Saturated Steam Enthalpy:(h) 4.@ 50inHg 5. @1000 Torr…

A: Pressure: h= 50 in HgP= 1000 TorrT=100CT= 200C

Q: A 2.5m3 rigid container contains saturated vapor at 2MPa. Determine the temperature and the mass of…

Q: Calculate the data from the table of thermodynamic properties of CO2 as an ideal gas

A: For an ideal gas ( enthalpy and internal energy are linear function of temperature only )

Q: Methane gas (CH) behaves like an ideal gas with y 1.306. Determine the molar heat capacity at…

Q: Refrigerant R-134a vapor in a piston-cylinder assembly, it is increased to 50°C under constant…

Q: Give an example for each of the following and provide explanation based from what you learned about…

A: Equilibrium process: The state of a thermodynamic system when the properties does not change with…

Q: 16. What is the most nearly the combined volume of 1.0g of hydrogen gas and 7.0g of helium gas when…

Q: Sketch a PV diagram and find the work done by the gas during the following stages. (a) A gas is…

A: Correct graph is option C Unit conversions: 1 atm = 1.013*105 Pa 1 liter = 0.001 m3 a) Pressure, P…

Q: One-quarter Ibmol of oxygen gas (O2) undergoes a process from p1 = 20 lb/in?, T1 = 500°R to p2 = 150…

Q: For adiabatic process, pressure before and after the process are 4000000 N/m2 and 2 bar…

Q: 2) One mole of an ideal gas is heated slowly so that it goes from the PV state (Pi , Vi ) to (3Pi ,…

Q: One-quarter Ibmol of oxygen gas (O2) undergoes a process from p1 = 20 lbf/in?, T1 = 500°R to p2 =…

Q: First law of thermodynamics introduces the property of O a. Mass Pressure O C. Enthalpy O d.…

A: First law of thermodynamics says that energy can never be created nor be destroyed. It only can be…

Q: Explain the calculation of entropy balance in a thermal system

A: Solution: The Entropy conservation pf a thermal system is shown below:

Q: Given the pressure - volume diagram (pp1.png). Assume ideal gas undergo cyclic process. Path AB is…

A: A cyclic process is the process in which initial and final states are same.An adiabatic process in…

Q: Complete the following table of thermodynamic properties for water:

Q: Define the Property diagrams of a pure substance.

A: A substance is said to be a pure substance if it is of homogenous chemical balance. Various…

Q: Draw the pv and Ts diagram of four different thermodynamic processes keeping one constant at a time.…

A: To draw: PV and TS diagram for four different thermodynamics process. Explanation: Constant volume…

Q: A closed cylinder is divided into two parts by a friction-free piston restricted from motion by a…

Q: 1 kg of Oxygen has initial volume of 2 x 106 cm3 is heated at Isobaric process from 298 K to 200°C.…

A: Given data: The mass of the oxygen is m=1 kg The initial volume is V1=2×106 cm3=2 m3 The initial…

Q: Write down any one type of energy term apart from ‘pV work’, which might be encompassed by the…

Q: Explain different thermodynamic processes with the help of Pv and Ts diagrams. Write thermodynamic…

Q: Two kilograms of Methane gas underwent an isopiestic process from 200C to 300C. Find the change in…

Q: 5 moles of monatomic gas undergoes two stages of thermodynamic processes. In the first stage, the…

Q: An airtight container with piston at 100 psi pressure and 70 °F temperature. When 100 Btu heat is…

A: Given that , Pressure at pistonP1=100psitemperatureT1 =70°Fheat transfferedQ =100Btuintial volumeV1…

Q: 10 mol of ideal gas are taken through the process illustrated on the pV diagram below. What is the…

A: Given:- n = 10 mol R = 0.010 kJ/kmol To Find:- Maximum temperature (T)

Q: THERMODYNAMICS Question An Ideal gas (molecular weight 30, ratio of specific heats 1.5) has a…

Q: What are the disadvantage of the Maxwell model and Kelvin model for the viscoelastic models?

A: Kelvin model: The spring and dashpot are placed parallel in the Kelvin model. In this model, the…

Q: Compute the mass of a 2m3 oxygen at 280 kPa and 40°C

Q: When the compositions and phases of a fluid reached equilibrium, it called thermal equilibrium Ture…

A: Given Statement:- When the compositions and phases of a fluid reached equilibrium, it called…

Q: ind these set of values in the steam table: Saturated Steam Enthalpy:(h) 8.@200F 9.@500K 10@ 1000R

A: To determine the enthalpy of saturated steam at given conditions.

Q: 1) Air contained in a piston-cylinder assembly undergoes the power cycle shown in the figure.…

Q: 1. Methane gas (CH4) behaves like an ideal gas with y = 1.306. Determine the molar heat capacity at…

Q: Explain about availability in thermodynamics in detail.. like formulas and when it's applicable and…

Q: Krypton (ideal monatomic gas) is confined in one-fourth of a 48-litre container. The other part of…

A: Given that, When the partition is removed i.e. condition after removal of partition.

Q: Define property. Explain with neat diagrams, the types of thermodynamics properties. Give at least 2…

Q: For a system to be in thermodynamic equilibrium, do the temperature and pressure have to be same…

A: A system is said to be in thermodynamic equilibrium it has to be in mechanical equilibrium, chemical…

Q: In the relation ∆u = mcv ∆T, what is the correct unit of cv — kJ/kg-°C or kJ/kg-K?.

Q: Ethylene is compressed according to pV1.15 = C from 1.5 MPa and 500°K to 2.8 MPa. The mass of…

A: Given data, m = 3 kg Process PV^1.15 = C P1 = 1.5MPa T1 = 500 K P2 = 2.8 MPa Find T2, W, Q

Q: What is the unit of adiabatic constant? A. Jkg B. Unit less, pure number C. J/kg D. J/kgk

A: Let us discuss about adiabatic constant.

Q: Complete the property table for water below. Use only the Thermodynamic Property Table for Water…

Q: the help of Pv and Ts diagrams. Write thermodynamic properties (P, v, T

Q: Given the pressure - volume diagram in figure below. Assume ideal gas undergo cyclic process. Path…

A: The molecules in an ideal gas doesn't interact with each and they continuously undergo collisions…

Q: Find the total heat in kJ required for ice at -15°C to become vapor at 120°C.

Concept explainers

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.

Question

Sketch these thermodynamic process on a PV diagram

Problem 1. At point A in a Carnot
cycle, 2.34 mol of a monatomic ideal
gas has a pressure of 1400 kPa, a
volume of 10.O L, and a temperature
of 720 K. It expands isothermally to
point B, and then expands
adiabatically to point C where its
volume is 24.0 L. An isothermal
compression brings it to point D,
where its volume is 15.0 L. An
adiabatic process returns the gas to
point A.

Science that deals with the amount of energy transferred from one equilibrium state to another equilibrium state.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At t = 350 degrees celcius and x = 88%. Determine Enthalpy, Internal Energy and Entropy with the used of steam tables.
CO2 needs to be compressed from p1=1bar, t1=300k to p2=40bar to transport it to remote sites for sequestration. what is the minimum energy requirement per kg of CO2 for the compressor? Should the compressor operate adiabatically or isothermally for the best energy efficiency? The environment is at Tenv=300k. Use accurate thermodynamic data for CO2 in this problem.
An ideal gas at an initial state of 4.1, atm.38°C is expandedirreversibly to a final state of 2 atm, 4.4oCAssuming the specific heats of the gas to be C= 0.5150 and Cv= 0.3098 kJ/kg-°K calculate the change in entropy.
IS IT TRUE THE ENTROPY CHANGE OF IDEAL GASES
REAL-WORLD APPLICATION, of Entropy of mixing in Idea Gases
Give only typing answer with explanation and conclusion Water vapor enters a continuous flow adiabatic turbine at 10 MPa pressure, 450°C temperature and 80 m/s velocity, and exits at 50 m/s velocity at 10 kPa pressure and 92 percent dryness. What is the enthalpy of the water vapor at the turbine inlet, in kJ/kg?
Determine entropy change of the gas, asap please
Select the correct relation for the isentropic process of ideal gases_________ A. B. C. D.
Thermodyanamics (Ideal Gas) air enters an ideal nozzle at a pressure of 45 psig with a temperature of 1,340F. The pressure at the nozzle exit is 14.925 psia. Determine the increase of kinetic energy of 1lb of air produced by an isentropic expansion through nozzzle, Btu/lb?
A gas turbine with reheat has a TIT of 1230°C, a compressor pressureratio of 16, and compressor and turbine efficiencies of 0.88 and 0.91,respectively. The pressure ratios of both the HP and LP turbine stages arethe same. The reheat occurs up to a temperature of 1230°C. The compressor inlet conditions are 20°C and 1.01 bar. The fuel mass flow rate may beignored.Determine (a) the pressures and temperatures at all real states of thecycle, (b) the turbine and compressor specific works and their ratio, and(c) the cycle thermal efficiency.
The isentropic equation of state for air as an ideal gas, gives
p89#9. a certain ideal gas whose R=278.6J/kgm.K and Cp=1.015kJ/kgm.K expands isentropically from 1517 kPa,288 degree celsius to 965kPa. fro 454gmm/s of this gas detrmine,(a)Wnf,(b) V2,(c) change of internal energy and (d) change in enthalpy.