A balloon structure weighing 5 kN carries a reinforcing steel bars weighing 10 kN . Determine the volume in cubic meter of gas compartment if helium is used. Unit weight of air is 0.021 kN/m3 and relative density f helium is 2.0 x 10-4 .

A balloon structure weighing 5 kN carries a reinforcing steel bars weighing 10 kN . Determine the volume in cubic meter of gas compartment if helium is used. Unit weight of air is 0.021 kN/m3 and relative density f helium is 2.0 x 10-4 .

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 3P: An astronaut has a mass of 68 kg. What is the weight of the astronaut on Earth at sea level? What...

See similar textbooks

Related questions

Q: Cars A and B approached each other on a straight road from points 457 meters apart. A has an initial…

Q: Solve the Ff. pNbloms A Pitot- státic tube (c, 1.6) is used to measure air speed with water…

Q: Use W27 x 84 as a flexural member with Fy = 50 ksi and Cb = 1.0, Use both methods, LRFD(Design…

A: Fy = 50ksi Md = moment due to dead load ML = moment due to live load [Note : moment capacity or…

Q: The rectangular bin with an inclined gate AB is filled with water to the depth shown. Determine the…

Q: 3. A company bought a new equipment costing P520,000 which will have a life of 10 years. Salvage…

A: step 1-

Q: 5-15 $-30 8=20 X-17-5 kN/m3 A-75" 20 5m

Q: 17 18 19 20 L The parabolic cable shown carries a uniform load of 90 kN/m. The lowest point of the…

Q: 16. The truss carries the loads shown. The support reaction at G is 7500 lbs going up. Draw a FBD to…

Q: • A steel shaft 50 mm diameter and 500 mm long is subjected to a twisting moment of 1100 N-m, then…

Q: An L- shape section composed of two 20 mm by 30mm rectangles. What is the section modulus of the…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

A: Given: shaft 1 Length Diameter Thickness Torque Shaft 2 Length Diameter Thickness Torque

Q: 4. For the beam and loading shown, determine the tension in the cable and the support reactions at…

A: As per guidelines we can solve one question at a time , please upload separately,Thanks Calculate…

Q: 20 kN 20 kN 20 kN 20 kN B 60° –3 m- – 3 m--3 m--3 m--3 m- 8 kN Prob. 2–19 →H

Q: The sewage from an area of 400 acres is to be carried by a circular sewer at a velocity not less…

A: Manning's equation : Manning's equation is an empirical equation that is a function of the channel…

Q: mm² in compression. 200

Q: Determine shear and moment equations of the beam shown. Neglect horizontal reactions since there are…

Q: For the beam and loading shown, determine the tension in the cable and the support reactions at…

Q: Structural Design 3.) Design a rectangular section to carry a load of p =32 kN/m over its whole span…

A: ASKED: To design a rectangular section for given beam. Given, Distributed load on the beam (p) =…

Q: ). A dense silt has the following properties: Void ratio (e) = 0.40, Specific 6. ( Gravity (Gs) =…

Q: A reinforced concrete beam has a width of 0.331m and an effective depth of 0.49m. f'c = 30MPa, Fy =…

A: Asmax = 0.85 * β * bd EuEu + Etf'cfy Where ; β = 0.85 b = 0.331 m = 331 mm d = 0.490 m = 490 mm Eu =…

Q: Find the design base shear for a 10-story steel special moment-resisting fra building, given the…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: The I-section displayed is made up of five boards (four 40x40mm and one 40x380mm). If the allowed…

Q: A wooden circular board 1-m diameter is being submerged vertically in a liquid having SG=1.15. Its…

Q: 2. The maximum amount of solid waste collected per day for one week is presented below. All the…

A: Given, Municipal waste to energy combustion =100 tonsday

Q: How are Steel Formed from start to finish? Provide a thorough discussion.

Q: 500 N -2 m 1 m 1 m- 100 N/m A.

Q: Determine the work of the force when it displaces 2 [m]. 500 N 2 m (a) 98.1 N 2 m (b) 2 m F- (6 s) N…

Q: Determine shear and moment equations of the beam shown. Neglect horizontal reactions since there are…

Q: A reverse curve connects two tangents which converged at an angle 30°. The direction of the second…

Q: ) Determine the support reactions and 1) Sketch the axial load, shear force and bending moment…

Q: 4. A soil strata can be described as 6 meters of sand underlain by 4 meters of clay with the water…

A: step 1-

Q: D

Q: In figure shown, use left end of the beam as reference and assume the upward reaction provided by…

Q: Classify each of the following as statically determinate, statically indeterminate or unstable.

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: 6. The eastings and northings of the corners of a closed area are taken as follows: A(0,0);…

Q: An L- shape section composed of two 20 mm by 30mm rectangles. What is the section modulus of the…

Q: Determine the design flexural strength in ft kips of a W10X26 of A242 (Fy = 50ksi) steel subject to…

Q: Design a rectangular section to carry a load of p =32 kN/m over its whole span of 3 m, including the…

Q: A vertical rectangular gate 1.8 m wide and 4.2 m high is submerged in oil (SG=0.88) with its top…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

Q: Refer to the diagram and consider that the pressure in each chamber is equal. Determine the…

A: Calculate the force due to pressure exerted on each of the pistons. Then compare the magnitude with…

Q: ASAP NEED IN 1 HOUR I'LL GIVE UPVOTE Design a 3.66 m simply supported slab to carry a uniform dead…

Q: 4. Find the moment of inertia about the x-axis of a thin plate bounded by the parabola X = y - y and…

Q: A rectangular concrete beam 260 mm wide and 381 mm deep is simply supported over a span of 11.57 m.…

Q: What is the specific weight of water at standard condition? If the local gravity is 9.75 mps2, the…

A: Data Available: Standard Condition Local gravity = 9.75 mps2 Asked: Specific weight of water at…

Q: Determine the warping stresses at interior edge and corner region in a 32 cm thick concrete pavement…

Q: For the beam shown, draw the shear diagram and bending moment diagram

Q: A plan drawn to a scale of 1:3000 was measured by mistake by a scale of 1:4000. The percentage error…

Q: Determine shear and moment equations of the beam shown. Neglect horizontal reactions since there are…

Q: .) Determine shear and moment equations of the beam shown. Neglect horizontal reactions since ther…

Concept explainers

Pressure and Stress

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the pressure required to decrease the volume of the oil by 2%?
A cylindrical tank 1m in diameter and 3m tall weighs 3.86kN. Given: ylead = 100kN/m3. Which of the following most nearly gives the weight of the lead that must be placed inside the tank to make the tank float vertically with 2.50m submerged in water?
A hollow cylinder 2.46-m in diameter and 7-m long weighs 3,159 N. How many cubic meters (m3) of metal weighing 112 kN/m3 must be placed inside the cylinder such that 2.9 m. of the cylinder is protruding above the liquid surface? The hollow cylinder is submerged in a liquid that has a specific gravity of 2.3. Round off to four decimal places.
Step by step A cylinder with a specific weight of 40 lb/ft^3 and floats in water (62.4 lb/ft^3) as shown below. If the cylinder has a diameter of 0.5 ft and a total height of 3 ft, calculate (a) the buoyant force on the cylinder , and (b) the depth that cylinder is submerged in the water.
Calculate the pressure decrease (in psi) when you climb from an elevation of 660 ft to a mountain top 1640 ft above mean sea level. Assume that the unit weight of air is constant at 0.07967 lb/ft^3.
The volume of the fluid inside the upright conical tank is 0.8 ft3.(a) Determine the needed volume to fill up the entire container.(b) Determine the height of the air from the peak and base of the tank.(c) If the mass of the fluid is 40 kg, determine its density. Use 2 decimal places.
Suppose that one such tank is cylinder shaped, 50ft high with a radius of 20ft. If we assume that water is pumped out of the tank via a pipe directly on top of the tank and that the tank is filled to a depth of 30ft, how much work (in ft-lbs) would be done by a pump to empty the tank? You may take the density of water to be 62.4 lbs/ft3
A hollow cylinder 1.55m in diameter and 7m long weighs 3,055N. How many cubic meters of metal weighing 105 kN/m3 must be placed inside the cylinder such that 2.6m of the cylinder is protruding above the liquid surface? The hollow cylinder is submerged in a liquid that has a specific gravity of 2.8.
What is the pressure of the air in the tank if z = 40 cm, y =100 cm, and x = 80 cm?
An object with a volume of 150 cm³ is weighed on an equal-arm balance. The standard mass required for balance is 0.433 kg and has a volume of 10 cm’. Calculate the required correction factor that necessary for air buoyancy.
A student with a mass of 80.0 kg runs up three flights of stairs in 12.0 sec. The student haa gone a vertical distance of 8.0m. Determine the amount of work done by the student to elevate his body to this height. Assume that his speed is constant.
Convert: 350 lb/ft^3 to kN/m^3, 200 lb·ft to N·m, and 8 ft/h to mm/s ?