A bar has a length of 8 in. and cross-sectional area of 12 in² Part A Determine the modulus of elasticity of the material if it is subjected to an axial tensile load of 10 kip and stretches 0.005 in. The material has linear-elastic behavior. Express your answer to three significant figures and include the appropriate units. HÅ 1333.28 kips Submit Previous Answers Request Answer Provide Feedback X Incorrect; Try Again; 8 attempts remaining Next >

A bar has a length of 8 in. and cross-sectional area of 12 in² Part A Determine the modulus of elasticity of the material if it is subjected to an axial tensile load of 10 kip and stretches 0.005 in. The material has linear-elastic behavior. Express your answer to three significant figures and include the appropriate units. HÅ 1333.28 kips Submit Previous Answers Request Answer Provide Feedback X Incorrect; Try Again; 8 attempts remaining Next >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Experiments were conducted in a tension testing machine to evaluate the material properties of two metallic rods both having diameter equal to 10 mm. First rod having modulus of rigidity of the material equal to 400 tonnes/cm2 when subjected to an axial tensile force of 6 kN, the change in its diameter was observed to be 0.0018 cm. The value for the bulk modulus of the second metallic rod is same as that of the first one but modulus of elasticity 18% more. Based on the material properties calculate and compare the values of different moduli as well as Poisson’s ratio for both metallic rods. Justify your answer with reasons.
The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mmdiameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stressstrain diagram determine the followings properties of the material (Poisson’s ratio of the material is 0.32) : a) Modulus of elasticityb) Yield strengthc) Toughnessd) Resiliencee) Shear modulusf) Bulk modulusg) Ductility as described bypercent change in length
A steel column is a cylinder 6.8 m long and 0.35 m in diameter. What is the change in length of the column when it experiences a tensile stress resulting from the application of a 3600 N force? The elastic modulus for steel is 20 × 1010 Nm2/kg2. ΔL = m
Question 1 In the strength of material, the section of the body involved is taken into consideration unlike the mechanics of materials. What is the force applied to a material divided by the area? a. normal strain b. normal stress c. strength d. shear stress e. external force Question 2 An 5.40 meter steel bar is loaded with a tensile load of 250 KN, determine the diameter of the steel bar if the elongation is limited to 4.8mm and E = 200 GPa. Choose the nearest answer. a. 42.50 mm b. 45.00 mm c. 90.00 mm d. 37.20 mm e. 105 mm
A cylindrical bar of metal having a diameter of 18.8 mm (A=278 mm^2) and a length of 198 mm is deformed elastically in tension with a force of 49400 N. Given that the elastic modulus and Poisson's ratio of the metal are 67.1 GPa and 0.34, respectively, determine the amount by which this specimen will elongate (in mm) in the direction of the applied stress.
Consider the modulus of elasticity of aluminum to be 10,000 lb / in2.Verify homogeneity in the units. An aluminum block of rectangular cross section is subjected to an axial compressive force, if the side measuring 1.5 in changes in length to 1.500132 in, determine the poisson's ratio and the new length of the side measuring 5 cm.
The deck of a bridge is made up of 12 mm thick steel plates 2 m long by 1·2 m wide. Under load, the plate is subject to tensile forces of 7·5 kN longitudinally and 6 kN across the width. Determine the change in the thickness of the plate under this load regime. Modulus of elasticity = 210 GN/m² and Poisson’s ratio = 0·3
A cylindrical bar of metal having a diameter of 20.0 mm and a length of 190 mm is deformed elastically in tension with a force of 50800 N. Given that the elastic modulus and Poisson's ratio of the metal are 61.4 GPa and 0.34, respectively, determine the following: (a) The amount by which this specimen will elongate in the direction of the applied stress. (b) The change in diameter of the specimen. Indicate an increase in diameter with a positive number and a decrease with a negative number.
A tensile test was conducted on a mild steel& the following data was obtained as follows. Diameter of the steel bar = 3 cm,Gauge length of the bar = 20 cm. Load at elastic limit = 250 kN . Extension at a load of 150kN = 0.21 mm . Maximum load = 380 kN . Total extension = 60 mm . Diameter of the rod at failure = 2. 25 cm Determine: (a) Young’s modulus (b) stress at elastic limit (c)the percentage of elongation (d) Percentage decrease in area.
A cylindrical structural element is made of steel. The element must withstand an axial load of 160 kN. Determine the diameter of its cross section so that it does not have plastic deformation. What is the load that this element resists if it is 80 cm long and suffers an elongation of 200 micrometers? Consider an elastic modulus of 200 G Pa. And a yield stress of 340 M Pa. Use a factor of safety of 3/5 with respect to the yield stress.
A mild steel bar went through a tensile test conducted at the University of San Carlos Mechanical Engineering Laboratory. The following data was obtained from the test: i. Diameter of the steel bar = 30 mm ii. Gauge length of the bar = 200 mm iii. Load at the elastic limit = 250 kN iv. Extension at a load of 150 kN = 0.21 mm v. Maximum load = 380 kN vi. Total extension = 60 mm vii. Diameter of the rod at the failure = 22.5 mm Determine the Young’s modulus, the stress at the elastic limit, the percentage elongation, and the percentage decrease in area.
In a standard tensile test a steel rod of 7/8 in. in diameter is subjected to a tension force of 17 kips. Determine the ratio of the shear modulus to the modulus of elasticity of a material whose Poisson's ratio is 0.25.