A bar having the cross section shown in Figure 2 has been formed by securely bonding brass and aluminum stock. Using the data given below, determine the largest permissible bending when the composite bar is bent about the hotizontal axis. Modulus of elasticity Allowable Stress Aluminum 70 GPa 100 MPa Brass 105 GPa 160 MPa

A bar having the cross section shown in Figure 2 has been formed by securely bonding brass and aluminum stock. Using the data given below, determine the largest permissible bending when the composite bar is bent about the hotizontal axis. Modulus of elasticity Allowable Stress Aluminum 70 GPa 100 MPa Brass 105 GPa 160 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.6.1P: A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned...

See similar textbooks

Similar questions

The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A square aluminum bar with pinned ends carries a load P = 25 kips acting at distance e = 2,0 in. from the center (sec figure). The bar has a length E = 54 in. and modulus of elasticity E = 10,600 ksi. If the stress in the bar is not to exceed 6 ksi, what is the minimum permissible width bminof the bar?
A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression is 400 MPa. The total load P that may be supported by the pad is 900 kN. Using a factor or safely 3.0 with respect to ultimate strength, determine the outer diameter of the pier if the thickness, is of the cross section is 12 mm.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
The cross sectional area of the bar is 5cm^2. Use E = 70GPa for aluminum, and E = 200 GPa for steel a. What is the elongation in segment AB (Aluminum)? b. What is the elongation in segment BC (Steel)? c. What is the elongation in segment CD (Aluminum)? d. What is the total elongation of the bar? -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
The cross sectional area of the bar is 5cm^2. Use E = 70GPa for aluminum, and E = 200 GPa for steel What is the elongation in segment AB (Aluminum)? a. 7.8571 x10^-3 m b. 6.8571 x10^-3 m c. -7.8571 x10^-3 m d. -6.8571 x10^-3 m What is the elongation in segment BC (Steel)? a. -3x10^-3 m b. 3x10^-3 m c. 2 x10^-3 m d. -2 x10^-3 m What is the elongation in segment CD (Aluminum)? a. -6.8571 x10^-3 m b. 6.8571 x10^-3 m c. -2.8571 x10^-3 m d. 2.8571 x10^-3 m What is the total elongation of the bar? a. 5 x10^-3 m b. 6 x10^-3 m c. 4 x10^-3 m d. -6 x10^-3 m -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
Applying the flexure formula, how can we determine the position of the absolute maximum bending stress that occur?
A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the data given below, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis.Modulus of elasticity 70 GPa,105 GPa Allowable stress100 MPa,160 MPa
a) i) The numerical value of plastic section modulus of the solid rectangular section is mm^3 ii) The numerical value of plastic moment of the solid rectangular section is N.mm b) The numerical value of ?t can be calculated as mm