A bar is subjected to fluctuating tensile load from 20 KN to 100 kN. The material has yield strength of 240 MPa and endurance limit in reversed bending is 160 MPa. According to the Soderberg principle, the area of cross-section in mm2 of the bar for a factor of safety of 2 is
Q: 1. What is the main function of a flywheel in an engine? 2. In what way does a flywheel differ from ...
A:
Q: Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the m...
A:
Q: A 9 ft A = 0.5 in.2 12 ft C A = 16 in.?
A: Find the stresses in each member
Q: (S) Sonic wave of air kg) "M2s 413 = Z (to a longer liquid KG (M3 950) and quickly sound) 's cm 7500...
A: Given Data,Zair=413 kg m2/sϕL=950 kgm2VL=750 m/s
Q: A slab of size 300 x 300 x 50 mm is require to be cast from a molten steel using a top riser of 170 ...
A:
Q: Determine optimum velocity ?
A: Given: Rotor diameter,d=9 mSpeed,N=2700 rpmNozzle angle,α=300Optimum velocity: It is defined as t...
Q: A flat steel bar 6 in wide by 1.5 in thick has axial loads applied with 1.250-in diameter pins in do...
A: Find stresses at required sections
Q: new temperature scale called the N-scale is to be defined using the ice point, at 0°C as 50°N and th...
A:
Q: In a concentrated solar power plant, molten salt tank is used to store the thermal energy from the s...
A:
Q: A steel rod of length L and uniform cross sectional area A is secured between two walls, as shown. U...
A:
Q: 62.A stone weighs 460 N in air. When submerged in water, it weighs 300N. Find the volume and specifi...
A:
Q: determine: a) the pressure, volume and temperature for each state, b) the work done between 1 and 3,...
A:
Q: A composite beam is constructed using a steel plate(0.5 in.x 6 in.) with two wood beams (3in. X 6 in...
A: Given Data The length of the steel plate is: l=0.5 in The breadth of the steel plate is: b=6 in The...
Q: The device shown is used to mix soils in order to provide in-sity stabilization. If the mixer is con...
A:
Q: A person is pushing on a uniform block of wood as shown in the figure and parameter table. The block...
A:
Q: Can you make it for me?(image below)just screenshot the result after you make the shape on the autoc...
A: Given 3D model To find View
Q: An infinitely long cylindrical container has a cross section area of radius R, and is placed horizon...
A: Pressure is caused by the force pressing on an area, according to physics. The weight operating on a...
Q: A medium size power station is used to produce 30 MW net power for a refinery. The station uses stea...
A: Given that, PH=35 bar,PL=0.4 bar, From the steam table, At P=35 bar,TH=242.5 °C,At P=0.4 bar,TL=75.8...
Q: Question 63 The dimensions of a solid rectangular beam sections (assume solid and homogeneous) are s...
A:
Q: A circular plate of diameter 3 m is immersed in water in such a way that its least and greatest dept...
A:
Q: temperature -20°C. Determine the condition of refrigerant at the end of the expansion ( outlet of ca...
A:
Q: One kilogram of air is compressed from a volume of 1.0 m and a pressure of 100 kPa to a volune of D....
A: Here diven Mass of the air m=1 kgInitial volume =V1=0.547 m3Initial pressure P1=400kpaFinal volume V...
Q: What does normal strain measure? Sum of elongation of different material original length per unit e...
A:
Q: Find the Pr number of a fluid having v = 0.001 ft2/s, k = 0.08 Btu/ft h F, cp = 0.45 Btu/lbm⋅F, and ...
A: Given Data- v = 0.001 ft2/s, k = 0.08 Btu/ft h F, cp = 0.45 Btu/lbm⋅F, and ρ = 58 lbm/ft3. We have t...
Q: 4. State 10 mechanical properties and their definition.
A: When we apply external force to the material, mechanical properties define how material will behave ...
Q: The specific gravity of mercury relative to water is 13.55. What is most nearly the specific weight ...
A: Specific gravity of Mercury, SGHg=13.55The specific weight of water, γw=62.4 lbf/ft3
Q: Consider a simple ideal Rankine cycle that operates between the pressure limits of 6 Mpa and 20 kPa....
A: Given:High pressure, P1=P4=6 MPaLow pressure, P2=P3=20 kPaTemperature of steam entering in turbine, ...
Q: An oil radiator has an outside surface area of 0.18 m2 and operates at a surface temperature of 85 d...
A: GIVEN DATA- AREA A=0.18m2 T1=85'C T2=16'C h=38.25 W/m2K
Q: E G 100 kN 3 m to 200 kN 3 m B 4 m
A: Force in member BC is 375 kN [Compression] and force in member CG is 125 kN [Tension].
Q: 150 kN 50 kN/m 20 kNm B 25 m 5 m 5 m
A:
Q: A 16mm Solid carbide tool with two teeth is used to machine Aluminium using the cutting speed of 275...
A:
Q: The type of braking method useful only as a means of lowering loads is A. plugging B. regenerative b...
A: “Since you have asked multiple question, we will solve the first question for you. If you want any s...
Q: The air in an automobile tire with a volume of 1.23 ft3 is at 72°F and 0.5 bar. Determine the amount...
A:
Q: Air compressor takes air of mass flow rate (9kg/min) at (100kPa) and (300K). Air leaves the compress...
A:
Q: food department is kept in an environment at 30°C. The total heat gain to the food department is est...
A: Write the given data in the problem. Q˙L=3300 kJ/hQ˙H=4800 kJ/h TL=-12°C+273 =261 KTH=30°C+273 ...
Q: For the series circuit in Fig. (1): a. Find the total resistance RT. b. Determine the source current...
A: a.Here all the resistances are in series connection. hence total resistance is given by RT = R1 + R2...
Q: Calculate the hourly heating load of a house in which all exterior surfaces have a thermal resistanc...
A: Given Thermal resistance, R = 14 ft2.h.oF/Btu Temperature, T1 = 65oF ...
Q: Determine the length of the fillet weld lap joint shown in the figure below. The weld has to resist ...
A:
Q: A 20 in. 30° 30 in. B A) Draw a FBD of the 150 Ib cylinder. B) Find the reactions on the cylinder. C...
A: Draw free body diagram and also find reactions Given data- Weight of cylinder = 150 lb
Q: The Rankine cycle with one closed feedwater heater (CFWH). Superheated water vapor enters the turbin...
A:
Q: 1) A simple vapour compression system using R12 as a refrigerant. The refrigerant enters the compres...
A: VCRS is a refrigeration cycle works on the principle of Rankine cycle in order to achieve the refrig...
Q: A person stands in front of a fire at 650°C in a room where air is at 5°C. Assuming the body tempera...
A: Answer: The net heat flow from the body is 291.1 W.
Q: A horizontal bracket ABC consists of two perpendicular arms AB of a length 0.75 m and BC of a length...
A: Dimeter of bar, d=65 mm=0.65 m,Length of arm (AB), b2=75 mm=0.75 m,Length of arm (BC), b1=50 mm=0.5 ...
Q: internal energy of the gas during the process.
A: Given: Work required in a cylinder is compressed,Work required for compression being=7500 kJDuring t...
Q: ɢɪᴠᴇɴ ᴀ ꜱʜᴇᴀʀ ꜱᴛʀᴇꜱꜱ ᴏꜰ ʀxʏ = 5000 ᴘꜱɪ ᴀɴᴅ ᴀ ꜱʜᴇᴀʀ ᴍᴏᴅᴜʟᴜꜱ ᴏꜰ ɢ = 1.15 x 10^7 ᴘꜱɪ, ꜰɪɴᴅ ᴛʜᴇ ꜱʜᴇᴀʀ ꜱᴛ...
A:
Q: 3- Air compressor compresses (7.8m/min) of air at (27°C) and (100kPa) to (925kPa). Determine the pow...
A:
Q: An inventor claims to have perfected an engine that will produce energy by absorbing heat from a fue...
A: Temperature of heat source, TH=300oC=300+273=573 KTemperature of surroundings, TL=15oC=288 KThermal ...
Q: Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load ...
A: Answer: The stress in each of the two vertical rods are: (a) Steel : 185.9158 MPa (Tensile stress). ...
Q: Given: A part is made of ductile material and subjected to principal stresses ơ1, 02, 03 . It is sta...
A: GIVEN: TO FIND:
Q: 15. A pump operating at 660 hp delivers water, from a large pressurized supply tank to a large press...
A: Given: The pump power, P = 660 hp The water flow rate, Q = 150 ft^3/s The total length, H = 1000 ft ...
Step by step
Solved in 4 steps
- An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
- A prismatic bar with a length L = 1 m and cross-sectional area A = 1200 mm2 is supported at the ends. The bar is then subjected to a temperature increase ?T = 25°C. Calculate the complete stale of stress acting on an inclined section .rs that is cut through the bar at an angle ?? = 45*. Use E = 200 GPa and the coefficient of thermal expansion a = 12×10-6/?.A W 8 × 28 beam of a length 10 ft is held between immoveable supports. The beam has a modulus of elasticity E = 29,000 ksi and coefficient of thermal expansion a = 6.5 ×10-6 /?. If the temperature of the beam is raised uniformly by an amount AT = 20°F, calculate the thermal stress aTin the beam.A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
- A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi..17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.
- Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.A metal bar AB of a weight Ills suspended by a system of steel wires arranged as shown in the figure. The diameter of the wires is 5/64 in., and the yield stress of the steel is 65 ksi. Determine the maximum permissible weight W max for a factor of safety of 1.9 with respect to yielding.A copper rod of length L = 18.0 in. is to be twisted by torques T (see figure) until the angle of rotation between the ends of the rod is 3.0°. (a) If the allowable shear strain in the copper is 0.0006 rad, what is the maximum permissible diameter of the rod? (b) If the rod diameter is 0.5 in., what is the minimum permissible length of the rod?