A barber’s chair with a person in it weighs 2150 N. The output plunger of a hydraulic system begins to lift the chair when the barber’s foot applies a force of 70 N to the input piston. Neglect any height difference between the plunger and the piston. What is the ratio of the radius of the plunger to the radius of the piston?

Q: One end of a hydraulic lift is a car weighing 9000 N. The other end contains a block with mass m.…

A:

Q: A cylindrical water tower is filled to a depth of 6.00 m, and has the dimensions shown in the…

A:

Q: The diameters of the large and small cylinders of a hydraulic press are 2.4 cm and 48.0 cm,…

A: As per Pascal’s law, the pressure on both the cylinder of the hydraulic press is the same, thus,…

Q: A fluid of a constant density flows through a reduction in a pipe. Find an equation for the change…

A: Given a fluid a constant density flows through a reduction in a pipe we have to find the an equation…

Q: A pipe of diameter 0.3 m increases to a diameter of 0.84 m. If the fluid is traveling at 4.6 m/s in…

A:

Q: In a hydraulic brake, a force of 100N is applied to a piston with area of 4 cm^2. a. What is the…

A: a) By the definition of the pressure we have P =F/A   = 100/4cm2 = 25N/cm2 P  = 25 N/cm2.(100cm/1m)2…

Q: †1m 2 m 4 m he flat surface shown is submerged vertically in water. Find the fluid force against the…

A: Given, The flat surface shown is submerged vertically in water. ρ = 9810 N/m3 Height , h = 2m Area =…

Q: Figure shows the effect of tube radius on the height to which capillary action can raise a fluid.…

A: The height of water in the capillary tube is

Q: A hydraulic lift has two pistons: a small one of cross-sectional area 5.00 cm- and a large one of…

A: Given: area of small piston, a = 5 cm2  area of large piston, A = 300 cm2 mass on large piston, M =…

Q: A container of cross-sectional area 122 cm2 contains liquid of density 1.75 g/cm3 to a height of…

A:

Q: An object with density of 418kg/m³ floats on a fluid. If only a third of the volume of the object is…

A:

Q: The Venturi tube shown in the figure below may be used as a fluid flowmeter. Suppose the device is…

A:

Q: The radius of the small piston is 5 cm, where the radius of the large piston is 30 cm .if a force of…

A:

Q: What force (in N) must be exerted on the master cylinder of a hydraulic lift to support the weight…

A: Given Data: The mass of the car is m = 2100 kg The diameter of the master cylinder is dm = 2.40 cm…

Q: A force of 150N is applied to a hydraulic jack piston that is 0.04 m in diameter. If the piston…

A:

Q: The ratio of the diameters of the two pistons in a hydraulic press is 1:4. What is the area ratio,…

A: We have, Given that ratio of diameters of two pistons in a hydraulic press is 1:4. Ratio of the…

Q: 1.2 kg lead mass rests on the bottom of a pool. (The density of lead is 11.3 x 10³ kg/m³ and the…

A: According to archemede's principle  Buoyant force =weight of liquid displaced

Q: An object of density p=816 kg/m3 floats face down in fluid of density pF1,381 kg/m³. It is observed…

A: Given, density of object , ρ = 816 kg/m3 density of fluid ,ρf = 1381 kg/m3 Let the full height of…

Q: In the diagram below, the vertical heights holl and hwater are 3.00 cm and 3.00 cm. The diameter of…

A:

Q: A hose has a radius r=3 cm is filling a storage dam that can accommodate a volume V=919 liters. The…

A: V=Volume of water=919 LA=Area=πr2r=Radius of hose=3 cmt=Time taken=7 minutesv=Velocity of…

Q: A force of 343 N is applied to a hydraulic jack piston that is 0.0388 m in diameter. The second…

A:

Q: In the hydraulic system, the piston on the left hasa diameter of 5.1 cm and a mass of 2.3 kg. The…

A: Write the expression for the pressure at left.

Q: Two pistons of a hydraulic lift have diameters of 60 cm and 5 cm. What is the maximum mass the…

A:

Q: In a hydraulic garage lift, the small piston has a radius of 4.0 cm and the large piston has a…

A: Given:

Q: The diameters of the large and small cylinders of a hydraulic press are 2.4 cm and 48.0 cm,…

A: Given Diameters of the large and small cylinders of a hydraulic press are d1= 2.4 cm and d2= 48.0…

Q: What force (in N) must be exerted on the master cylinder of a hydraulic lift to support the weight…

A:

Q: A force of 295 N is applied to a hydraulic jack piston that is 0.026 m in diameter. The second…

A: GivenF1 = 295 Nd1 = 0.026 md2 = 0.19 m

Q: A very simple way of measuring the depth of a fluid in a gas station's underground gasoline tank is…

A: Given that                   The density of the gasoline is (ρ) = 700kg/m3                    The…

Q: A force of F1 = 374 N is applied to a hydraulic jack pump piston with a diameter of D1 = 0.0192 m.…

A:

Q: An aquarium was filled with salt water at a depth of 0.5 m. What is the pressure due to the liquid?…

A:

Q: As shown in the figure below, a hydraulic system has two pistons of different diameter and uses a…

A:

Q: A force of F1 = 397 N is applied to a hydraulic jack pump piston with a diameter of D1 = 0.0183 m.…

A: In this question we have to find the magnitude of the output force F2. Please give positive feedback…

Q: In a car service station, a force of 130 N is required to raise the car on the hydraulic lift. If…

A: Given: The applied force is 130 N. The diameter of the hydraulic lift is 21 times as radius of…

Q: A hydraulic lift consists of a circular input piston of diameter 20 cm coupled to a circular output…

A: Given:input piston diameter, di = 20 cm = 0.2 moutput piston diameter, do = 5.0 mfluid used is…

Q: In a simple hydraulic system piston 1 has a cross section area of 0.000050 m2 , and piston 2 has a…

A: Given: The cross-section area of piston 1 is 0.00005 m2. The cross-section area of piston 2 is…

Q: A hydraulic jack is used to lift a load of weight 1000 N. The load-bearing cylinder has a radius of…

A: Hydraulic jack works on Pascal law. F1A1=F2A2F1=F2A2×A1 F1 and F2 are the forces on smaller and…

Q: An automobile of mass 600 kg is supported by a hydraulic lift having a large piston of…

A: (a)          Since the pressure is same at all points, The pressure applied to the piston and pedals…

Q: The diameters of the pistons on a hydraulic press are 5.0 cm and 40 cm. When a force of 50 N is…

A: Given data:  Diameter of smaller piston (d1) = 5.0 cm = 0.05 m Diameter of larger piston (d2) = 40…

Q: Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on…

A: Given:  P = 80 kPa d (mercury) = 13600 kg/m3 d (water) = 1000 kg/m3

Q: A square metal sheet 2.8 cm on a side and of negligible thickness is attached to a balance and…

A:

Q: A force of F1 = 345 N is applied to a hydraulic jack pump piston with a diameter of D1 = 0.0168 m.…

A:

Q: A car of mass 800 Kg is hoisted on the large cylinder of a hydraulic press. The area of the large…

A: Given data: Mass of the car (m) = 800 kg Area of large piston (A2) = 0.35 m2 Area of small piston…

Q: The pressure at the bottom of a cylindrical container with a cross-sectional area of 49.0 cm? and…

A:

Q: A hydraulic jack has an input piston of area 0.0560 m2 and an output piston of area 0.750 m2. How…

A: input area, a = 0.056 m2  output area, A = 0.75 m2  Output force, F = 1.4 x 104 N

Q: What is the flow rate of water (in m3/s) hose that can fill 1.75 L bottle in 5 seconds? Group of…

A: Given, Volume of water = 1.75 L = 1.75×10-3 m3 Time = 5s  Flow rate = Volume filledTime taken

Q: The small piston of a hydraulic lift (see figure below) has a radius of r1= 1.00 cm, and its large…

A: Please see the answer in step 2