A-B+C (D E-F) Write program to evaluate the arithmetic statement X = with three address instructions. using a general register computer G+H*K

Q: 1. Explain what happens when the instruction sequence below is executed. LAHF MOV [BX+DI], AH

A: 1.  LAHF : Copies flag register's lower byte into AH register MOV[BX+DI],AH : This will move the…

Q: 53. Write an instruction sequence that generates a byte-size integer in the memory location defined…

A: Write an instruction sequence that generates a byte size integer in the memory location defined as…

Q: write the below expression in the form of three, .two, one, and zero address instructions .x=a+b*c-d

A: According to the information given:- we have to write expression in the form of three two , one and…

Q: B part if do able A         Instruction Set Architecture A.1        Instruction set We present a…

A: An assembly language is a low-level programming language designed for a specific type of processor.…

Q: 53- write an instruction sequence that generate a byte-size integer in the memory location defined…

A: (RESULT) = (AL). (NUM1) + (AL).(NUM2---) + (BL) NOT [NUM2] ;(NUM2) <-- (NUM2---) MOV CL, AL AND…

Q: Write Assembly instructions to perform below given operation: X = A* 2D / B Where assume that A is a…

A: Assembly Language : It is a low level language designed for the particular processor. It uses…

Q: 2. a) List the internal registers in 8085 microprocessor, their abbreviations and lengths(bits) b)…

A: Give question is based on microprocessor 8085 and 8086

Q: Function X = (A-B)(C-DE) Create a programme that computes the function using the following address…

A: The Answer is in given below steps

Q: 0S Let the clock cycles required for various operations be as follows: Register to trom memory…

A: The answer for total number of clock cycles is

Q: 1. Explain what happens when the instruction sequence below is executed. LAHF MOV [BX+DI] , AH

A: Solution: LAHF : copies flag register's lower computer memory unit into AH registerMOV[BX+DI],AH :…

Q: Q4/ a- Write a program to moving a block of 160 bytes of data. Where the source memory blocks start…

A: ANSWER:-

Q: Q3: The original contents of CX, AX, memory location Beta, and carry flag (CF) are FFE116, 11AB16,…

A: Answer: I have given answered in the handwritten format

Q: Assembly to Binary 2 An LC-3 assembly language program contains the instruction LEA R6, Z The symbol…

A: Explaination, As we know that the value stored at Y ie at x3005 will be the 16 bit binary code for…

Q: (d) Assume that a, b, c, x are stored in registers $s1-$s4. Translate the fol- lowing high-level…

A: MIPS stands for "Million instruction per second". MIPS assembly language is simply assembly code or…

Q: Write the following assembly language codes: a) Write a single instruction to add the carry flag to…

A: According to guidelines, I can only solve three parts. a) ADC AH, AH ADC is used for addition with…

Q: Microprocessors Fundamentals ENT 237 Homework 1 Problem2: For the following memory requirements,…

A: a) Using equation  Number of bits required = Log2(48) + 10 Number of bits required = 6 + 10 Number…

Q: A-Develop an assembly program that transfer a block of 100H bytes from memory location A00h to…

A: The register used here are C,H,A,D . MVI instruction is used to move the data .

Q: Write all the possible Opcodes of Memory-reference instruction in basic computer (write Opcodes in…

A: Memory-reference istruction: The basic computer has 16-bit instructionregister (IR) which can denote…

Q: Convert the following assembly language program into machine code by using Motorola 6800 data sheet.…

A: The Answer is in Below Steps

Q: write the below expression in the form of three, two, one, and zero address instructions. x=a+b*c-d.

A: Given that  x= a+b*c-d

Q: c) Design and write an assembly language program for the 68000 Microprocessor that can give an…

A: 68000 processor has 16 registers that are directly accessible by the user. Those are: 8…

Q: Q1. An instruction is stored at location 300 with its address field at location 301. The address…

A: The address is used for storing the variable and data initialized to that it is like a box where the…

Q: A-B+C (D E-F) Write program to evaluate the arithmetic statement X = with three address…

A: The Answer is in below Steps

Q: The memory unit of a computer has 2M words of 32 bits each. The computer has an instruction format…

A: Given :            Memory Unit = 2M words                                   = 2 x 220…

Q: The term endian refers to a computer architecture's: O address modes. O ability to find the end of…

A: The correct answer is (d) byte order.

Q: (b) Two 16-bit numbers are to be subtracted: $2762- $1296. Assume R16 = ($62) and R17 = ($27). Place…

A: Answer: We explain  code in easy way and simple

Q: Loading One's Location Enter the bit pattern of an instruction which loads its address into register…

A: I Have answered this question in step 2.

Q: Assume AL=23h; CL=05. Write the content of AL after ROL AL, CL - showing the calculation steps.…

A: solution :STC − Used to set carry flag ##CF to 1ROL − Used to rotate bits of byte/word  _towards the…

Q: 1) Write simple instructions (simple program) that will add two consecutive bytes of data storied…

A: In Direct addressing mode, we directly give the address of the location, where we want to retrieve…

Q: Given a 8-bit number at memory location 2050H. Write 8085 instruction to move the value stored at…

A: Given 8-bit number at memory location 2050H. The instruction to move the value to the required…

Q: y= B*A - C²+ CB-A/B -C] write a program segment to show the equation above using O address and…

A: We need to write program segment to compute the mentioned expression.

Q: The states of the instruction cycle involve operand address calculation which means that the…

A: Algorithms and algorithmic problem resolving that can concern as a central place in computer science…

Q: 6. (1) (Please explain why a branch delay slot is needed after a branch instruction. (2)) Please…

A:

Q: A. Ox4000 and Ox40000, respectively. Store the result in the $s0 register. NOTE: You must use real…

A: The MIIPS program is given below:-

Q: 4] Using the ASC instruction set, write a program to perform: IF A B THEN X A-B ELSE X - A+B. Assume…

A: ASC: ASC stands for Advanced Scientific Computer. It is a supercomputer manufaxtured by Texas…

Q: Assume AL=23h; CL=05. Write the content of AL after ROL AL, CL- showing the calculation steps.…

A: STC instruction will set the carry flag initially.

Q: Instruction Description LD RI, 45(R2) Read data from memory and store in R1. Memory address is…

A: Answer:-

Q: 8 Find the physical address of the memory locations referred in the following instructions if…

A: 8086, via its 20 bit address bus, can address 220 = 1,048,576 or 1 MB of different memory locations.…

Q: 6. Identify the addressing mode for the following instructions: a) MUL CL b) OUT DX, AL c) MOV [BX],…

A: Dear Student, In the Question - MUL CL - Register Addressing Mode , as register is the one that is…

Q: 2. Write the assembly language program code for the following flowchart. b) Sketch a diagram showing…

A: Find the required assembly language code given as below :

Q: Translate the following high-level codes into assembly language. f=(g-h)+(i-j)    Assume…

A: An assembly language is a low-level programming language designed for a specific type of processor.…

Q: Explain in detail What are 1 byte, 2 byte and 3 byte instructions in 8085 microprocessor.Give one…

A: Actually, 8085 microprocessor is a 8-bit data bus.

Q: Q2/ Write an instruction sequence that generates a byte-size integer in the memory location defined…

A: Actually, 1 byte= 8 bits.

Q: 8. Performance of microprocessor is measured in what is called million instructions they can execute…

A: 8.Clock speed 9..Destination index 10.The address part of instructions holds the begining base…

Q: 2. Assume that these registers contain the following: A=F0,B=55, and R1-90. Perform the following…

A:

Q: 2. Assume that there are the positive numbers in memory locations from x3000 to x300F. Write a…

A: According to the question, we have to find the maximum even value and then display this value using…

Q: Q8/Assume that the microprocessor can directly address 64K with a R/W' and 8 data pins The memory…

A: Given: Assume that themicroprocessor can directlyaddress 64K with a R/W' and 8 data pins The memory…

Q: B) The 8-bit registers A, B, C & D are loaded with the value (F2) hes. (FF) hes. (B9) hes and (EA)…

A: Lets us calculate the value of the registers , A= (F2)hex= (11110010) B= (FF)hex= (11111111) C=…

Q: Q5) A basic computer system has four registers R, to R4, an accumulator AC, and memory unit. For the…

A: Answer is given below .