A beam ABCDE is continuous over four supports and carries the loads shown in the following Figure. Determine the values of the fixing moment at each support and hence draw the shear force and bending moment diagrams for the beam. 1 kN/m m 20 kN 3kN/m 13-1 -am B 3m 10 KN E Ro

A beam ABCDE is continuous over four supports and carries the loads shown in the following Figure. Determine the values of the fixing moment at each support and hence draw the shear force and bending moment diagrams for the beam. 1 kN/m m 20 kN 3kN/m 13-1 -am B 3m 10 KN E Ro

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.15P: Determine the fixed-end moments (MAand MB) and fixed-end forces (R4and Rs) for a beam of length L...

See similar textbooks

Related questions

Q: Determine the steady state time response x(t) of a viscously damped system subjected to harmonic…

A: The mass is .The damping coefficient is .The spring stiffness is .The base excitation is

Q: What is the stress in a rectangular rod that is 20 mm by 30 mm in cross-section if is supporting a…

A: Given data:- load =1000 Ncross-section area =20 mm 30 mmTo find:-the stress in a rectangular rod (…

Q: What is the vertical component of the force?

Q: P8-2. The internal loadings act on the section. Show the stress that each of these loads produce on…

A: The state of stress at a point symbolizes the total number of independent stresses acting on the…

Q: Consider the flow field V = (ay+dx)i + (bx-dy)j + ck, where a(t), b(t), c(t), and d(t) are time…

A: To prove that the density is constant following a fluid particle, we need to show that the material…

Q: CHI) plane Cho use your knowledge of Geometry and the Vale a = (7-92 X1000) cm to determine the Sur…

A: There are three half spheres and three 60 degree angle spheresIt is asked to find the surface…

Q: Describe the role of microchips in the automotive industry, including applications in advanced…

A: Microchips are essential in modern vehicles, controlling everything from engine performance to…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: Problem 14.66 The girl has a mass of 50 kg and center of mass at G. (Figure 1) Figure 1 B of 1 2 m A…

Q: 10 AN 2.5 m 153.2 R 38 5 m 20 KN 2 m 20 kN 2 m

Q: e the challenges and strategies for ensuring reliability in autonomous vehicles.

A: Autonomous vehicles are an advanced mode of vehicle driving. From the name auto means self and…

Q: Assessment 11.0: Welding processes Produce a short report with diagrams (min 300 words) on the…

A: Given:• Alumino-thermic• Flash butt welding

Q: For the control volume shown below, use Eq. 4.16 with the parameter bequal to the velocity to…

Q: Assume a system receives 10 kJ of heat, but then sheds half of it back to the environment. It also…

Q: Find the enthalpy change for vaporizing 1 kg of water at 125°C and 232.1 kpa. What is the latent…

Q: 3.1 3.2 Determine the location of the centroid for the cross-section shown below and draw a scaled…

Q: Determine the support reactions: T 4 m + 4 m 150 KN 6 m 25 kN/m -10 m-

Q: Problem 4 A long 1.5 km pipeline with size of 300 mm laid between two reservouirs having difference…

Q: Find the factor of safety using the distortion energy theory. The diameter of the shaft is 20 mm. F1…

A: The properties of cold steel AISI 1006 are,

Q: The solid shaft shown below is in equilibrium, supported at two bearings A and B. The pulleys C and…

Q: The particle shown is constrained to move along the slotted path defined by the horizontal…

A: Given data:Angular position is Angular velocity is Angular acceleration is Equation of spiral path…

Q: Given: 8 = 880 Kg/m³ m = 10 kg/s = 88.9mm 3.5x25.4= 88.9x10³m - 1 &in = 1.625in = 1.625x25.4 =…

A: Density, ρ=880kg/m3Mass flow rate, m˙=10kg/sDiameter,…

Q: Structure and Injecting Energy

A: The concepts of "Structure" and "InjectingEnergy" These terms can have various meanings depending…

Q: The transformation of position from polar to Cartesian coordinates is given by: x=rcose y=rsin 0…

Q: Your company is drilling a deep oil well in Texas. Fluids pressure encountered in that well at 15000…

A: Depth of the oil well: Pressure encountered: (pounds per square inch gauge)Acceleration due to…

Q: A cylinder disk is being rotate as shown in the figure below with an axis of rotation going through…

Q: A journal of diameter 150 mm runs in a bearing 300 mm long. The lubricant used has a density of 855…

Q: Which is more efficient the Diesel Cycle or the Otto cycle

A: Otto cycle.1. The Otto cycle is the thermodynamic cycle used in spark-ignition gasoline engines.1.…

Q: onsider an electrical motor with mass M = 117 kg located at the tip of a rigid beam pivoted at point…

A: Total machine massSpring constantDamping coefficientLength of the beamUnbalance massEccentricityThe…

Q: beam shaped as a rectangle, with a width represented by b and heightindicated by h, bears a centered…

A: Here,

Q: Determine the force in each member of the loaded truss. All triangles are isosceles. Forces are…

A: Determine the force in each member of the loaded truss.All triangles are isosceles.Forces are…

Q: The 2-kg block is held in equilibrium by the system of springs. Draw a free-body diagram for the…

Q: The following data refers to an axial flow compressor: B1 = 60°, turning angle = 30°, degree of…

A: An axial flow compressor-β1 = 60°, turning angle = 30°, degree of reaction = 50%, speed N = 36000…

Q: Provide a real life example of BERNOULLI'S EQUATION OF MOTION

A: Bernoulli's equation describes the relationship between pressure, fluid velocity, and elevation in a…

Q: a.) Determine the reaction force at B and C b.) if average shear stress is not to exceed 160 MPa…

A: Draw the schematic diagram for the system.

Q: Quest-5 b, The distance between two parallel shafts connected by Oldham's coupling is 25 mm. The…

Q: Water is pumped through a pipeline to a height of 10 m at the rate of 0.1 m³/s, friction and other…

A: Height h = 10 mflow rate Q = 0.1 m³/sLosses L = 5 mSo the hydraulic head representing the water to…

Q: Start a new Part in SolidWorks. Make a 1" diameter x 5" tall cylinder. Put a 0.5" diameter hole…

A: Given that-Diameter of cylinder = 1'' = 1 inchHeight of cylinder = 5'' = 5 inchDiameter of hole at…

Q: Give the expression for the shear force, V = V(x), and the bending moment, M = M(x), as a function…

A: Given a simply supported beam with loads as shown in the figurethe objective is to determine…

Q: Q4) Determine the moment of inertia of the cross-sectional area about the x and y axes. 20 mm t 20…

Q: In a gas turbine plant, air enters the compressor at ambient conditions of 100 kPa and 25°C with a…

Q: 25.18 The following is an initial-value, second-order differential equation: dx ²+(5x) + (x +7) sin…

A: To decompose the given second-order differential equation into a system of first-order differential…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: The angular velocity of AB is .

Q: Q- The reduction of speed from 360 rpm to 120 rpm is desired by the use of a chain drive. The…

A: The reduction of speed from 360 rpm to 120 rpm,So, speed N1=360 rpm,N2=120 rpm,The driving sprocket…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: According to the given data We need to findThe angle

Q: Derive Hamilton's equations governing and 0.

A: collar is attached to the vertical shaft by fork and clevis , so the angle of inclination , of AB…

Q: For the spring system shown in the above figure, determine the displacement of each node. In the…

A: The given spring system can be represented as individual spring elements with joints 'i' and 'j' as…

Q: Two rotating rods, AE and BP, in the vertical plane are connected by a slider block, P, of…

Q: If the resultant (single equivalent force) of the two forces and couple M passes through point O,…

Q: 1.33 Figure P1.33 shows a storage tank holding natural gas. In an adjacent instrument room, a U-tube…

Question

mecha

Exercise 2:
A beam ABCDE is continuous over four supports and carries the loads shown in the following Figure.
Determine the values of the fixing moment at each support and hence draw the shear force and bending
moment diagrams for the beam.
20 KN
HH
3m
Re
Rc
1 kN/m
-5 m
3 kN/m
am
10 kN
Ro
Im

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: A continuous beam

VIEW

Step 2: Step-2;

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The beam ABC shown in the figure is simply supported at A and B and has an overhang from B to C Draw the shear-force and bending-moment diagrams for beam ABC. Note: Disregard the widths of the beam and vertical arm and use centerline dimensions when making calculations.
Determine the fixed-end moments (MAand MB) and fixed-end forces (R4and Rs) for a beam of length L supporting a triangular load of maximum intensity q0(see figure). Then draw the shear-force and bending-moment diagrams, labeling all critical ordinates.
A beam of length L is designed to support a uniform load of intensity q (see figure). If the supports of the beam are placed at the ends, creating a simple beam, the maximum bending moment in the beam is qL2/8. However, if the supports of the beam are moved symmetrically toward the middle of the beam (as shown), the maximum bending moment is reduced. Determine the distance a between the supports so that the maximum bending moment in the beam has the smallest possible numerical value. Draw the shear-force and bending-moment diagrams for this condition. Repeat part (a) if the uniform load is replaced with a triangularly distributed load with peak intensity q0= q at mid-span (see Fig. b).
The simple beam ACE shown in the figure is subjected to a triangular load of maximum intensity q0= 200 lb/ft at a = 8 ft and a concentrated moment M = 400 Ib-ft at A. Draw the shear-force and bending-moment diagrams for this beam, Find the value of distanced that results in the maximum moment occurring at L/2. Draw the shear-force and bending-moment diagrams for this case. Find the value of distance a for which Mmaxis the largest possible value.
A beam supporting a uniform load of intensity q throughout its length rests on pistons at points A, C and B (sec figure). The cylinders are filled with oil and are connected by a tube so that the oil pressure on each piston is the same. The pistons at A and B have diameter d1and the piston at C has diameter D2. (a) Determine the ratio of d2to d1so that the largest bending moment in the beam is as small as possible. Under these optimum conditions, what is the largest bending moment Mmaxin the beam? What is the difference in elevation between point C and the end supports?
Find expressions for shear force V and moment M at v = L/2 of beam AB in structure (a). Express V and M in terms of peak load intensity q0and beam length variable L. Repeat for structure (b) but find Fand M at m id-span of member BC.
Find expressions for shear force V and moment M at x = x0of beam AB in terms of peak load intensity q0and beam length variable L. Let x0= L/2.
Cantilever beam AB carries an upward uniform load of intensity q1from x = 0 to L/2 (see Fig. a) and a downward uniform load of intensity q from x = L/2 to L. Find q1in terms of q if the resulting moment at A is zero. Draw V and M diagrams for the case of both q and qtas applied loadings. Repeat part (a) for the case of an upward triangularly distributed load with peak intensity q0(see Fig. b). For part (b), find q0, instead of q1
Draw the shear-force and bending-moment diagrams for a cantilever beam AB acted upon by two different load cases. A distributed load with linear variation and maximum intensity q0(see figure part a). A distributed load with parabolic variation and maximum intensity q0(see figure part b).
A propped cantilever beam is subjected to two triangularly distributed loads, each with a peak load intensity equal to q0(see figure), lind the expressions for reactions at A and C using superposition. Plot shear and moment diagrams.
At a full d raw, an archer applies a pull of 130 N to the bowstring of the bow shown in the figure. Determine the bending moment at the midpoint of the bow.
A beam with a sliding support at B is loaded by a uniformly distributed load with intensity q. Use the method of superposition to solve for all reactions. Also draw shear-force and bending-moment diagrams, labeling all critical ordinales.