A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.41 from the support. (MPa) Properties: Beam width = 206 mm Beam height = 495 mm Pu = 66.2 kN Span of the beam = 11 m Prestressing force = 335 kN eccentricity = 105 mm

A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.41 from the support. (MPa) Properties: Beam width = 206 mm Beam height = 495 mm Pu = 66.2 kN Span of the beam = 11 m Prestressing force = 335 kN eccentricity = 105 mm

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

A propped cantilever beam of length ? = 1 m, with an inner hinge at point B, carries a uniformly distributed load ?, as shown in Figure Q1 (a). The beam is made from a circular hollow section with an inner radius of ?? = 5 cm and a thickness of ? = 2 cm (refer to Figure Q1 (b)). The maximum allowable longitudinal stress of the beam is 150 N/mm2.
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at top of the beam section at 3.09 from the support. (MPa) Properties: Beam width = 259 mmBeam height = 447 mmPu = 63.85 kNSpan of the beam = 10 mPrestressing force = 502 kNeccentricity = 96 mm
A beam has a uniform concentrated load (Pu) at midspan and has a fixed support at both end. If the beam properties are given below, what is the stress at bottom of the beam section at 2.76 from the support. (MPa)
A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and carries a concentrated load of 25 KN at the midspan. What is the maximum flexural stress of the beam? Blank 1 (use two decimal places)
The girder of a simple log bridge supports a wheel load W acting at any position along the span. In addition, the weight of one log and the planks it supports is equivalent to a uniform load of 850 N/m acting on the log. Determine the maximum permissible wheel load W (in kN) based on an allowable shear stress of 0.75 MPa if the maximum shear stress on circular sections is 4/3 of the shear force divided by the cross-sectional Choices: 28.9 38.7 77.4 30.2 Note:please help me in this sample problem thank you
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
The major and minor principal stresses acting at a point are 50 Pa compression and 10 Pa compression, respectively. Draw the Mohr’s circle for this stress combination, and determine the magnitude of shear and normal stress on one of the planes where shear is a maximum.
For the overhanging beam loaded as shown, determine the maximum values of flexural stress and horizontal shearing stress developed
If M=6kip.ft, determine the maximum tensile stress in the beam shown in the figure below
A girder has a uniform T cross-section with a flange 250 mm × 50 mm and web 220 mm × 50 mm. At a certain section of the girder, there is a shear force of 360 kN.Plot neatly to scale the shear-stress distribution across the section, stating the values:(a) where the web and the flange of the section meet.(b) at the neutral axis.
Determine the shear stress at points A and B on the beam if it is subjected to ashear force of V = 400 kN. Represent the state of stress on a volume element of these points.