A belt 200 mm wide and 7 mm thick drives a pulley at belt speed of 25 m/s. The density of the belt is 980 kg/m3 and the coefficient of friction between the belt and pulley is 0.23. Given that the angle of contact of pulley is 2π/3 and the allowable stress of the belt is 1.8 MPa, determine the tension on the slack side of the belt (T2) in N

A belt 200 mm wide and 7 mm thick drives a pulley at belt speed of 25 m/s. The density of the belt is 980 kg/m3 and the coefficient of friction between the belt and pulley is 0.23. Given that the angle of contact of pulley is 2π/3 and the allowable stress of the belt is 1.8 MPa, determine the tension on the slack side of the belt (T2) in N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
.Two pulleys which are 270 mm in diameter and which are run at 1030 rpm are connected by a V-belt with an angle of groove of 30°. The cross-section area (b x t) of the belt is 750 mm2 and the maximum tensile stress in the material is 4.8 MPa. Determine the power transmitted between the pulley in kW if the centrifugal tension of the belt is 439 N and the coefficient of friction between belt and pulley is 0.19.
A flat belt connects pulley A to pulley B. The coefficients of friction are μs = 0.25 and μk = 0.20 between both pulleys and the belt. Knowing that the maximum allowable tension in the belt is 4 kN, determine the largest torque which can be exerted by the belt on pulley A. The radius of the bigger pulley A is R = 203 mm and the radius of the smaller pulley B is r = 25.4 mm. Calculate the resulting bearing force in A.
....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
A belt drive is required to transmit 10 kW from a motor running at "600 rpm. The belt is 12 mm thick -and -has a mass density of 0.001 g/mm3. Safe stress in the belt is not to exceed 2.5 N/mm2. Diameter of the driving pulley is 250 mm, whereas the speed of the driven pulley is 220 rpm. The two shafts are 1.25 m apart. The coefficient of friction is 0.25. Determine the width of the belt.
A 600-lb safe rolls on four 2-in.-diameter steel wheels. The wheels rotate on 1/4 in.-diameter axles. If the coefficient of friction between the wheel and the axle is 0.45, determine the force necessary to push the safe and the ratio of the rolling friction to the axle friction.
A 20 kg block is held in place on an incline plane as shown by a rope that passesover a frictionless pulley at B and then over a fixed cylinder at C where thecoefficient between the rope and the fixed cylinder is 0.2. Given an angle ofincline, A = 25°, if a force of P = 200 V is applied to the end of the rope,(a) Will the block move if the coefficient of static friction between the block and theinclined surface is M, = 0.56?(b)If impending motion exists, will the block tip or slip?
The weight of the motorcycle is 151 kg and the weight of the driver is 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m Determine the required frictional force.
A 85-kg man starts climbing a ladder that leans against a wall as shown in Figure Q1. If the ladder is 5 m long and weighs 10 kg. Determine the normal reaction (in N) at the vertical surface if the coefficient of friction is 0.25 at the top vertical surface and 0.4 at the bottom horizontal surface.
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimension l1 = 0.31 m and l2 = 0.23 m Determine the required coefficient of friction