A block of wood has a mass of 3.67 kg and a density of 669 kg/m³. It is to be loaded with lead (1.13 x 10“ kg/m³) so that it will float in water with 0.806 of its volume submerged. What mass of lead is needed if the lead is attached to (a) the top of the wood and (b) the bottom of the wood? (a) Number i 52 Units (b) Number i Units

A block of wood has a mass of 3.67 kg and a density of 669 kg/m³. It is to be loaded with lead (1.13 x 10“ kg/m³) so that it will float in water with 0.806 of its volume submerged. What mass of lead is needed if the lead is attached to (a) the top of the wood and (b) the bottom of the wood? (a) Number i 52 Units (b) Number i Units

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter4: Mechanical Processes

Section: Chapter Questions

Problem 4.16P

See similar textbooks

Similar questions

If a 5-kg steel plate is attached to one end of a 0.1m x 0.3m x 1.2m wooden pole, what is the length of the pole above the water? Use density of wood 0.50. Neglect buoyantforce on steel.
A cylindrical tank, 1m in diameter and 2m high weighs 1090 Newtons. The tank is to float in water with a draft of 1.7m. Unit weight of lead is 110 kN/m^3. How much lead is required if it is to be placed inside the tank?
A plank of wood 200 mm thick is floating in seawater withspecific gravity of 1.03. Find the minimum area of a block whichwill support a package weighing 80 kg. Assume that the plank iscompletely submerged but floating.
A 1.2-ft3 block of aluminum is tied to a piece of cork (SG=0.22), as shown. What volume of cork is required to keep the aluminum (SG=2.7) from sinking in castor oil (SG=0.96)?
A 1.22mdiameter sphere floats half submerged in salt water (γ = 10.05 kN/ ). What minimum weight of concrete (γ = 23.56 kN/ ) used as an anchor will submerge the sphere completely?
Situation 2. A hollow cylinder 1.0 m in diameter and 2.0 m long weighs 3285 N. a. How many kN of lead weighing 110 kN/m³ must be fastened to the outside bottom to make the cylinder float vertically with 1.50 m submerged in fresh water? b. How many kN of lead weighing 110 kN/m³ must be placed inside the cylinder to make the cylinder float vertically with 1.50 m submerged in fresh water? c. What additional load must be placed inside the cylinder to make the top of the cylinder flush with the water surface?
A solid wood cylinder has diameter 0f 2.0 ft and a height of 4.0 ft. The specific gravity of the wood is 0.60. If the cylinder is placed vertically in oil (s.g. = 0.85), would it be stable? Given: γwood = 37.44 Ib/ft3 , γoil = 53.04 Ib/ft3
A freshly cut log floats with one-fourth of its volume protruding above the water surface. determine the specific weight of the log.
A block of wood 0.6m x 0.6m x “h” meters in dimension was thrown into the water, if floatswith 0.18m. Projecting above the water surface. The same block was thrown into a container of a liquid having a sp.gr. Of 0.90 and it floats with 0.14m projecting above the liquid surface. A. Determine the value of “h”.B. Determine the sp.gr. of the block.C. Determine the weight of the block.
The deep submersible vehicle ALVIN weighs approximately36,000 lbf in air. It carries 800 lbm of steel weightson the sides. After a deep mission and return, two 400-lbmpiles of steel are left on the ocean fl oor. Can you explain,in terms relevant to this chapter, how these steel weightsare used?
A hollow cylinder 1 m in diameter and 2 m long weighs 3825 N. Determine the weight of lead having a density of 110 kN/m^3 must be placed inside to make the cylinder float vertically with 1.5 m submerged in fresh water. a. 6.75 kN b. 8.56 kN c. 7.73 kN d. 8.05 kN
A block of wood with an area of 1.50 m^2 is floating in an oil. The specific gravity of wood is 0.64 while theat of oil is 0.80. Find the volume of the wood in cubic meter which will support a box on the wood weighing 30kg.