A bowling ball is dropped from a boat so that it strikes the surface of a lake with a speed of 15 ft/s. Assuming the ball experiences a downward acceleration of a =10 - 0.01v when in the water, determine the velocity of the ball when it strikes the bottom of the lake.

A bowling ball is dropped from a boat so that it strikes the surface of a lake with a speed of 15 ft/s. Assuming the ball experiences a downward acceleration of a =10 - 0.01v when in the water, determine the velocity of the ball when it strikes the bottom of the lake.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A particle is projected from a horizontal plane and has an initial speed of 50m/s at an angle of 30 degrees above the horizontal. For how long is the particle at least 20 m above the level of the plane? Hint: You may use the formulas for the horizontal x(t) and vertical y(t) displacement of the particle: x(t) = ucos(α)t, y(t) - usin(α)t - ½gt2 , g = 10m/sec2.
A chemical storage tank ruptures at a point 2 m hove the ground. Chemical leaves the tank in a jet inclined at 15 degrees to the horizontal, travelling at 10 m/s. If the flight of the chemical is ballistic and effects of air resistance are ignored, how far from the base of the tank does the jet reach? (Take g = 9.8 m/S^2). (A) 9.23 m (B) 5.10 m (C) There is not enough information to calculate the answer D) 7.61 m
In humans, blood flows from the heart into aorta, from which it passes into major arteries These branch into the small arteries (arterioles), which in turn branch into myriads of tiny capillaries. The blood returns to the heart via the veins. The radius of the aorta is about 1.2 cm, and the blood passing through it has a speed of about 40 cm / s. A typical capillary has a radius of about 0.0004 cm, and blood flows through it at a speed of about 0.05 cm / s. Estimate the number of capillaries that are in the body
A jet of water whose diameter is 5cm strikes a fixed cup with a velocity of 9.45m/s and is deflected by 165 degree. The jet leaves with a velocity of 30m/s . if the cup offers a reactive force of 26.5N to the jet when the flow rate was 980 N/min. Determine the ratio of a) Actual to theoretical forces of the jet. b) Velocities at outlet and inlet. Assume any missing data.
A horizontal 5-cm-diameter water jet with a velocity of 18 m/s impinges normally upon a vertical plate of mass 1000 kg. The plate rides on a nearly frictionless track and is initially stationary. When the jet strikes the plate, the plate begins to move in the direction of the jet. The water always splatters in the plane of the retreating plate. Determine (a) the acceleration of the plate when the jet first strikes it (time 5 0), (b) the time it takes for the plate to reach a velocity of 9 m/s, and (c) the plate velocity 20 s after the jet first strikes the plate. For simplicity, assume the velocity of the jet is increased as the cart moves such that the impulse force exerted by the water jet on the plate remains constant.
As a young engineer, you have been tasked to select the location of a wind turbine based on the details of the location and relevant specification below:Air densityAverage air velocityDiameter of wind turbine bladesLOCATION A1.29 kg/m3 54 km/h 70 mLOCATION B1.21 kg/m3 63 km/h 60 m By comparing the amount of power generated (in MW) at Location A and Location B, determine the location that will give the optimum wind power generation.9 kg of Refrigerant 134-a is initially at 26.69°C with enthalpy of 100 kJ/kg. Heat is transferred to the refrigerant under a constant-pressure process until the entropy of the refrigerant reaches 0.9795 kJ/kg.K.(i) Determine the final temperature of the refrigerant(ii) Calculate the boundary work, Wb, in kJ.Assist your answer with a proper P-v diagram indicating the properties,process, and boundary work region clearly.(iii) Explain the reason behind the high amount of boundary work obtained in (ii).Assist your explanation with relevant sketching.
A block of mass m slides along a horizontal surface lubricated with a thick oil which providesa drag force proportional to the square root of velocity.F_d=-bv^1/2If v = v0 at t = 0, determine v as a function of time
A gun is on the same horizontal level as a target 484 meters away. A bullet is fired from the gun with a muzzle velocity of 154m/s. At what angle of elecation should the muzzle of the gun be set in order to ensure the bullet hits the target? Hint: You may use the formulas for the horixzontal x(t) and vertical y(t) displacement of the particle: x(t) = ucos(α)t, y(t) - usin(α)t - ½gt2 , g = 10m/sec2.
Fluid Mechanics A horizontal jet of water exits a nozzle with a uniform velocity of Vj = 20 m/s and area of Aj= 3 cm^2, and strikes a flat plate that moves to the right at velocity of Vc = 15 m/s. Upon impinging the plate, the jet splits into an equal upward and downward half-jet. (i.e. A1 = A2 = 0.5Aj). Neglecting gravity and viscous forces, determine the force (in both x - and y - directions) required to keep the plate moving at a constant velocity.
When rowing downstream consider the following scenario. The current of the water is moving at 2 m/s in the direction you are rowing. The coefficient of drag between your boat and the water is 1.2, the area in contact with the water is 0.1 m2 and the density of the water is 1000 kg/m3. You are moving at a velocity of 4 m/s into a head wind of 4 m/s. Your coefficient of drag between you and the air is 1.4, the area in contact with the air is 0.4 m2 and the density of the air is 1.2 kg/m3. Your goal is to create a net force moving downstream that is equal to 100 N. How much force must you exert with the oar and in what direction to achieve this net force downstream?
A 50. 95mm diameter horizontal jet of water strikes a plate. .Determine the velocity of the jet if 50N of horizontal force is required to move the plate at 2.95m/s at the same direction as that of jet. Choices: 7.90 9.70 79.0 0.97 Note: please help me in this sample problem and please base your answer on the choices given thanks for the help
Fast pls i will give u like for sure solve this question correctly in 5 min pls Consider a solid bar of length L with variable cross-sectional area given by A(x) , where x ∈ [0, L] is distance along the bar. If the sides of the bar are insulated and if A(x) varies slowly, it is reasonable to make an approximation in which the heat flows only in the x direction. Consider the rate of change of the total thermal energy between arbitrary positions x = a and b to derive a heat equation for the bar in terms of the temperature u(x, t) . You may assume the density, heat capacity and thermal conductivity are constant (i.e. constant thermal properties) and that there is no heat source.